Hostname: page-component-848d4c4894-mwx4w Total loading time: 0 Render date: 2024-06-28T11:58:37.835Z Has data issue: false hasContentIssue false
  • English
  • Français

Unlubricated Sliding Properties of Ion Beam and Excimer Laser Mixed Fe-Ti-C Multilayered Films

Published online by Cambridge University Press:  25 February 2011

J-P. Hirvonen ,
M. Nastasi ,
T. R. Jervis ,
J. R. Tesmer  and
T.G. Zocco
J-P. Hirvonen
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545, USA
M. Nastasi
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545, USA
T. R. Jervis
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545, USA
J. R. Tesmer
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545, USA
T.G. Zocco
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545, USA
Get access

Abstract

Multilayered Fe-Ti-C films consisting of eleven sublayers were vacuum deposited onto an AISI 304 stainless steel substrate and subsequently mixed using either 400 key Xe ions or an excimer laser operating at a wavelength of 308 nm. Ion mixing was accomplished in a two step process: the multilayers were first irradiated with 1×1017 Xe/cm2 at 520°C, after which half of the sample was irradiated with 5×1015 Xe/cm2 at 0 °C. Laser mixing was carried out at both i.i and 1.7 J/cm2 with the number of pulses varied between 1 and 10. Pin-on-disc studies revealed only slight differences between the two kinds of ion beam mixed samples, whereas the dry sliding properties of laser mixed samples were strongly dependent on the total fluence used. In the optimum conditions, similar friction coefficients were obtained on both kinds of samples.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 128: Symposium A – Processing and Characterization of Materials Using Ion Beams , 1988 , 451
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Hirvonen, J-P., Nastasi, M., and Mayer, J.W., J. Appl. Phys. 60, 980 (1986).Google Scholar
2. Jervis, T.R., Nastasi, M., and Zocco, T.G., Mat. Res. Soc. Proc. 100, 621 (1988).CrossRefGoogle Scholar
3. Jervis, T.R., Nastasi, M., Zocco, T.G., and Martin, J.A., Appl. Phys. Lett. 53, 75 (1988).Google Scholar
4. Hirvonen, J-P., Nastasi, M., Phillips, J.R., and Mayer, J.W., J. Vac. Sci. Technol. A 4, 2997 (1986).Google Scholar
5. Hirvonen, J-P., Nastasi, M., and Mayer, J.W., Appl. Phys. Lett. 49, 1345 (1986).Google Scholar
6. Jervis, T.R., Hirvonen, J-P., and Nastasi, M., J. Mat. Res. Nov-Dec. (1988). In press.Google Scholar
7. Jervis, T. R., Hirvonen, J-P., Nastasi, M., Zocco, T.G., Martin, J.A., Pharr, G.M., and Oliver, W.C., this symposium.Google Scholar
8. Follstaedt, D.M., Knapp, J.A., Pope, L.E., Yost, F.G., and Picraux, S.T., Appl. Phys. Lett. 45, 529 (1984).CrossRefGoogle Scholar
9. Singer, I.L. and Jeffries, R.A., Appl. Phys. Lett. 43,925 (1983).CrossRefGoogle Scholar
10. Pethica, J.B., Hutchins, R., and Oliver, W.C., Nucl. Inst. Meth. 209/210, 995 (1983).CrossRefGoogle Scholar
11. Hirvonen, J-P., Nastasi, M., and Mayer, J.W., Mat. Res. Soc. Proc. 93, 335 (1987).CrossRefGoogle Scholar
12. Hirvonen, J-P., Nastasi, M., and Mayer, J.W., Nucl. Inst. Meth. B13, 479 (1986).Google Scholar
13. Nastasi, M., Tesmer, J.R., and Hirvonen, J-P., Mat. Res. Soc. Proc. 93, 215 (1987).Google Scholar
14. Hirvonen, J-P., Mayer, J.W., Nastasi, M., and Stone, D., Nucl. Inst. Meth. B23, 487 (1987).CrossRefGoogle Scholar