Hostname: page-component-848d4c4894-2xdlg Total loading time: 0 Render date: 2024-07-02T01:58:32.410Z Has data issue: false hasContentIssue false
  • English
  • Français

Tribological and Mechanical Properties of Fe/Ti Multilayered films

Published online by Cambridge University Press:  16 February 2011

M. Nastasi ,
J-P. Hirvonen ,
T. R. Jervis  and
S. N. Basu
M. Nastasi
Affiliation:
Los Alamos National Laboratory, Los Alamos, NM 87545
J-P. Hirvonen
Affiliation:
Los Alamos National Laboratory, Los Alamos, NM 87545
T. R. Jervis
Affiliation:
Los Alamos National Laboratory, Los Alamos, NM 87545
S. N. Basu
Affiliation:
Los Alamos National Laboratory, Los Alamos, NM 87545
Get access

Abstract

A 900 Å as-deposited multilayered structure of alternating Fe and Ti on hardened tool steel has been examined for tribological and mechanical properties. The multilayer in contact with a 52100 steel ball counter surface possessed a 0.16 friction coefficient and showed good wear character after 1000 cycles in pin-on-disk experiments. Nanoindentation experiments show a 20 % increase in hardness for material in the wear track. Electron microscopy data suggests that the as-deposited bcc-Fe plus hcp-Ti multilayer composite transforms to a nanocrystalline alloy plus bcc-Fe by solid state reaction during pin-on-disk friction and wear test. The low friction observed in these surface films is attributed to the formation of a hard nanocrystalline alloy and improved interlayer and film/substrate adhesion which result during solid state reaction.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 188: Symposium K – Thin Films: Stresses and Mechanical Properties II , 1990 , 301
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Singer, I.L. and Jeffries, R.A., Appl. Phys. Lett. 43, 925 (1983).Google Scholar
2. Follstaedt, D.M., Knapp, J.A., Pope, L.E., Yost, F.G., and Picraux, S.T., Appl. Phys. Lett. 45, 529 (1984).Google Scholar
3. Hirvonen, J-P., Nastasi, M., Phillips, J.R., and Mayer, J.W., J. Vac. Sci. Technol. A4, 2997 (1986).Google Scholar
4. Hirvonen, J-P., Nastasi, M., and Mayer, J.W., Appl. Phys. Lett. 49, 1345 (1986)Google Scholar
5. Jervis, T.R., Hirvonen, J-P., Nastasi, M., Zocco, T.G., Martin, J.A., Pharr, G.M., and Oliver, W.C., in New Materials Approaches to Triboloqy: Theory and Application, eds., Pope, L.E., Fehrenbacher, L.L., and Winer, W.O. (Materials Research Society, Pittsburgh, 1989) p. 189 Google Scholar
6. Hirvonen, J-P., Nastasi, M., Jervis, T.R., and Zocco, T.G., Thin Solid Films, in press.Google Scholar
7. Doerner, M.F. and Nix, W.D., J, Mater, Res. 1, 601 (1986).Google Scholar
8. Hirvonen, J-P., Nastasi, M., and Mayer, J.W., J. Appl. Phys. 60, 980 (1986).Google Scholar
9. Schwarz, R.B. and Johnson, W.L., eds., “Solid State Amorphizing Transformations”, Journal of the Less-Common Metals 140, (1988).Google Scholar
10. Hirvonen, J-P., Nastasi, M., Zocco, T.G., and Jervis, T.R., J. Appl. Phys., in press.Google Scholar
11. Hirvonen, J-P., Nastasi, M., and Jervis, T.R., in preparation.Google Scholar