Hostname: page-component-5c6d5d7d68-sv6ng Total loading time: 0 Render date: 2024-08-07T22:34:10.269Z Has data issue: false hasContentIssue false
  • English
  • Français

Superplastic Deformation and Mechanisms of the Commercial Aluminium Alloy Al-4Cu-I.6Mg-0. 8Mn

Published online by Cambridge University Press:  16 February 2011

Yuwen Liu ,
Guang Yang ,
Jianshe Lian  and
Xianwen Zeng
Yuwen Liu
Affiliation:
Jilin University of Technology, Dept.of Metal Materials Engineering, Changchun, 130025, P.R. China
Guang Yang
Affiliation:
Jilin University of Technology, Dept.of Metal Materials Engineering, Changchun, 130025, P.R. China
Jianshe Lian
Affiliation:
Jilin University of Technology, Dept.of Metal Materials Engineering, Changchun, 130025, P.R. China
Xianwen Zeng
Affiliation:
Jilin University of Technology, Dept.of Metal Materials Engineering, Changchun, 130025, P.R. China
Get access

Abstract

The superplastic deformation behavior and mechanisms of commercial Al-4cu-1.6 Mg-0.0Mn have been studied, using tensile tests with microstructuraL observations being carried out by optical and transmission etectronmicroscopy. The results of tensile tests show that considerable superplasticflow can be obtained without any pretreatment to this atloy.The maximum elongaton achieved is 42096 and the strain rate sensitivity index, m, is 0.49. Microstructural analysis reveals that the dominant mechanism in the early stage of deformation is diffusion. As strain increases, grain-borundary sliding and grain rearrangment take the dominant part in thedeformation process, and diffusion becomes an accommodation mechanism. Second phase particles effectively restrict grain growth during deformation. Cavity initiation and growth during deformation are the direct cause of specimen failure.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 196: Symposium T – Superplasticity in Metals, Ceramics, and Intermetallics , 1990 , 391
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Paton, N.E. et at., J. Met, (August) (1982), 21Google Scholar
2. Backofen, W.A. et at., Trans.ASM, 57 (1964), 980 Google Scholar
3. Lioyd, D.J. and Moore, D.M., In Superplastic Forming of Structural Alloys, ed.Paton, N.E. and Hamilton, C.H.(AIME) New York,(1982),147 Google Scholar
4. Mcqueen, H.J. and Baudelet, B., Proceeding of the Fifth International Conference on the Strength of Metals And Alloys, l, ed.P. Heaasen et at.,(1979),329Google Scholar
5. Kayebiechive, O.A., Superpnasticity of Metals, Moscow,(1975)(In Russian)Google Scholar
6. Mohamed, F.A. et at.,Acta Metalt.,23(1975),1443 Google Scholar
7. Bricknell, R. H. and Benttey, A. P., J. Mater. Sci. 14(1979),2547 Google Scholar
8. Kuanfu, Ha, Mechanics Behaviour And Microstructure of Metats, Science Press,(1983),(In Chinese)Google Scholar
9. Hamilton, C. H. et at., In Superptastic Forming of Structural Attoys, ed. Paton, N. E. and Hamilton, C. H. (AIME.) New Youk,(1982),191 Google Scholar
10. Geckinil, A. E., Met. Sci. 17 (1983),12 Google Scholar