Hostname: page-component-848d4c4894-nr4z6 Total loading time: 0 Render date: 2024-05-21T02:34:55.426Z Has data issue: false hasContentIssue false
  • English
  • Français

The Structure and Properties of MoSi2-Mo5Si3 Composites

Published online by Cambridge University Press:  15 February 2011

H. Kung ,
D. P. Mason ,
A. Basu ,
H. Chang ,
D. C. Van Aken ,
A. K. Ghosh  and
R. Gibala
H. Kung
Affiliation:
Department of Materials Science and EngineeringThe University of Michigan, Ann Arbor, MI 48109
D. P. Mason
Affiliation:
Department of Materials Science and EngineeringThe University of Michigan, Ann Arbor, MI 48109
A. Basu
Affiliation:
Department of Materials Science and EngineeringThe University of Michigan, Ann Arbor, MI 48109
H. Chang
Affiliation:
Department of Materials Science and EngineeringThe University of Michigan, Ann Arbor, MI 48109
D. C. Van Aken
Affiliation:
Department of Materials Science and EngineeringThe University of Michigan, Ann Arbor, MI 48109
A. K. Ghosh
Affiliation:
Department of Materials Science and EngineeringThe University of Michigan, Ann Arbor, MI 48109
R. Gibala
Affiliation:
Department of Materials Science and EngineeringThe University of Michigan, Ann Arbor, MI 48109
Get access

Abstract

The addition of Mo5Si3 as a reinforcing second phase in a MoSi2 matrix has been investigated for possible high temperature strengthening effects. MoSi2 with up to 45 vol % Mo5Si3 was fabricated using powder metallurgy (PM) and arc-casting (AC) techniques. Effects of processing routes, which result in different microstructures, on their mechanical properties are given. PM composites, which have an equiaxed microstructure, exhibit a limited increase in hardness. Higher hardnesses are observed in script-structured AC eutectics and Er-modifiedeutectics throughout the temperatures studied (25–1300°C). Crack propagation paths induced by indentation show long transphase cracks in the AC materials vs short intergranular and interphase cracks in the PM composites at high temperatures.

Transmission electron microscopy discloses that the interface in the AC composites has a low-index orientation relationship between the two phases and shows regularly faceted interfacial structures, while planar interfaces are found in the PM composites. These observations suggest the interface is stronger and lower in energy in the AC composites, which is consistent with the higher hardness values and long transphase cracks observed.

Dislocation analysis shows the presence of ordinary dislocations (<100>, <110> and 1/2<111>) in MoSi2 in the as-fabricated composites. These types of dislocation are also responsible for the high temperature plastic deformation in compression in both the monolithic MoSi2 and the composites. <331> types of dislocation are only found in MoSi2 either near the interface of the AC composites or in materials deformed below 1000°C.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 273: Symposium Q – Intermetallic Matrix Composites II , 1992 , 241
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Tuominen, S.M., J. Less-Common Met. 81, 249 (1981).Google Scholar
2. Aikin, R.M. Jr., Ceram. Eng. Sci. Proc. 12. 1643 (1991).CrossRefGoogle Scholar
3. Ashby, M.F., Blunt, F.J. and Bannister, M., Acta metall. 31, 1847 (1989).Google Scholar
4. Kung, H., Chang, H. and Gibala, R. in Interfacial Structure and Properties of Interfaces in Materials, edited by Clark, W.A.T., Dahman, U., and Briant, C.L., Mater. Res. Soc. Proc. 23, Pittsburgh, PA 1992, p. 599.Google Scholar
5. Gibala, R., Ghosh, A.K., Aken, D.C. Van, Srolovitz, D.J., Basu, A., Chang, H., Mason, D.P. and Yang, W., Proceedings, First High Temperature Structural Silicides Workshop, A.K. Vasudevan and J.J. Petrovic, eds., Mater. Sci. and Eng. A155 (1992).Google Scholar
6. Aikin, R.M. Jr., Scripta metall. mater. 26, 1025 (1992).Google Scholar
7. Li, W.B., Henshall, J.L., Hooper, R.M. and Easterling, K.E., Acta metall. mater. 32, 3099 (1991).CrossRefGoogle Scholar
8. Ghosh, A.K., Basu, A. and Kung, H., this meeting.Google Scholar
9. Unal, O., Petrovic, J.J., Carter, D.H. and Mitchell, T.E., J. Amer. Ceram. Soc. 73, 1753 (1990).Google Scholar
10. Umakoshi, Y., Sakagami, T., Hirano, T. and Yamane, T., Acta metall. mater. 38 909 (1990).CrossRefGoogle Scholar