Hostname: page-component-848d4c4894-cjp7w Total loading time: 0 Render date: 2024-06-19T18:55:06.786Z Has data issue: false hasContentIssue false
  • English
  • Français

A Review of Creep of Silicides and Composites

Published online by Cambridge University Press:  25 February 2011

K. Sadananda  and
C.R. Feng
K. Sadananda
Affiliation:
Materials Science and Technology Division, Naval Research Laboratory, Washington D.C. 20375
C.R. Feng
Affiliation:
Materials Science and Technology Division, Naval Research Laboratory, Washington D.C. 20375
Get access

Abstract

A review of creep behavior of molybdenum disilicides and their composites is presented. Creep rates of these silicides are compared with those of other high temperature materials such as superalloys, ceramic-ceramic composites, intermetallics including aluminides (nickel and titanium), berylides (vanadium and niobium), and refractory metals(molybdenum and tungsten). Creep rates of silicides are shown to be very sensitive to grain size even in the power-law creep regime with grain size exponent of the order of five and above. In addition, the results show that with increase in volume fraction of reinforcements there is a decrease in creep rates for volume percentages less than 25%. To achieve significant improvement in creep strength volume percentages of reinforcements greater than 25% are required. This weakening effect at low volume percentages is related to accompanying decrease in grain size with the addition of reinforcements. Addition of carbon to MoSi2 eliminated the silica present at grain boundaries and converted it to SiC. The SiC thus formed, inhibited grain growth during hot pressing. Thus although addition of carbon enhanced creep resistance, its effect is masked by the accompanying decrease in grain size. Thus, grain size plays a dominant role in the creep of molydisilicide composites. It is shown that among all the materials molybdenum disilicides possess very high creep resistance comparable to ceramic-ceramic composites.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 322: Symposium F – High-Temperature Silicides and Refractory Alloys , 1993 , 157
Copyright
Copyright © Materials Research Society 1994

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Sadananda, K., Jones, H., Feng, J., Petrovic, J. J., and Vasudevan, A.K., Ceram. Eng. Sci. Eng. Proc., 12, 1671–1678 (1991).Google Scholar
2. Sadananda, K., Feng, C.R., Jones, H., and Petrovic, J.J., Mater. Sci. Eng., A155, 227–239. (1992)Google Scholar
3. Sadananda, K. and Feng, C.R.., in Proc. Processing, Fabrications, and Manufacturing of Composite Materials, edited by Srivatsan, T.S. and Lavernia, E.J., (American Society of Mechanical Engineers, New York) MID, 35, 23–245 (1992).Google Scholar
4. Sadananda, K. and Feng, C.R.., in Advanced Composites '93, edited by Chandra, T., Dingra, T.S., (TMS Publication, Warrendale, PA), 603–610 (1993).Google Scholar
5. Sadananda, K. and Feng, C.R., Processing and Fabrication of Advanced Materials for High temperature Applications - II, edited by Ravi, V.A. and Srivatsan, T.S.,(TMS publication, Warrendale PA), 331 (1993)Google Scholar
6. Sadananda, K. and Feng, C.R., in “Aspects of High Temperature Deformation and Fracture in Crystalline Materials, edited by Hosoi, et al. (Japan Institute of Metals, Tokyo) 391 (1993).Google Scholar
7. Sadananda, K. and Feng, C.R., Mater. Sci. Engrg., A170, (1993) 199–214.CrossRefGoogle Scholar
8. Sadananda, K. and Feng, C.R., Petrovic, J. J., in Int. Symp. on Structural Intermetallics, Seven Springs Symp. In Press (1993).Google Scholar
9. Weiderhorn, S.M., Gettings, R.J., Roberts, D.E., Ostertag, C. and Petrovic, J.J., Mat. Sci. Engrg., A 155, 217–226 (1992).Google Scholar
10. Bose, S., Mat. Sci. Engrg., A 155, 217–226 (1992).Google Scholar
11. Ghosh, A. K., and Basu, A., in Critical Issues in the Development of High Temperature Structural Materials, edited by Stoloff, N. S. et al. (TMS Publication, Warrendale) (1993)Google Scholar
12. Maxwell, W.A., Some Stress-Rupture and Creep Properties of Molybdenum Disilicide in the Range of 1600-20009F, NACA RME52D09, (1952).Google Scholar
13. Deve, H.E., Weber, C.H., Maloney, N., Mat. Sci. Engrg., A153, 668 (1992)CrossRefGoogle Scholar
14. Umakoshi, Y., Bull. Jpn. Inst. Metals. 30, 72 (1991).Google Scholar
15. Suzuki, M. and Nutt, S.R. and Aiken, R. M. Jr., Mater. Sci. Engrg., A162, 73 (1993).Google Scholar
16. Mason, D.P. and Aken, D.C. Van, in High Temperature Ordered Intermetallics, edited by Baker, I, Doralia, R., Whittenberger, J. D. and Yoo, M.H., (Mater. Res. Soc. Proc. 286, Pittsburgh, 1992) 1129–1134; D. K. Patrick D.C. Van Aken, ibid., pp 1135-1141;Google Scholar
17 French, J. D. and Weiderhorn, S. M., Presented at the 1993 MRS Fall meeting, Boston, MA 1993 Google Scholar
18 Ashby, M. F. and Brown, L. M., “Perspectives in Creep Fracture”, Pergmon Press, Oxford, 1983).Google Scholar
19 Hokey, B.J., Weiderhorn, S.M., Liu, W., Baldoni, J.G. and Buljan, S.T., J. Mater. Sci. 26, 1991, 3931 Google Scholar
20. Donachie, M.J. (ed) “Superalloys - Source Book”, American Society of Metals, Metals Park, OH, 1984.Google Scholar
21. Bieler, T.R., Whittenberger, J.D. and Luton, M.J., in High Temperature Ordered Intermetallics. edited by Baker, I., Doralia, R., Whittenberger, J. D. and Yoo, M.H., (Mater. Res. Soc. Proc. 286, Pittsburgh, 1992) pp 1149–1154; C.R. Feng and K. Sadananda, ibid., pp. 1155-1160.Google Scholar
22. Nieh, T.G., Wadsworth, J., Grensing, F.C., Yang, J.M., J. Mater. Sci. 27 (1992) pp 2660–2664.Google Scholar
23. Nieh, T.G., Wadsworth, J., chou, T.C., Owen, D. and Chokshi, A.H., J. Mater. Res. 8, 757–763 (1993).Google Scholar
24 Pavlinov, L.V. and Bikov, V. N., Fiz. Met. i Metalloved, 18, 459, (1964)Google Scholar
25. Robinson, S.L., Sherby, O.D., Acta Met. 17, 109 (1969).CrossRefGoogle Scholar