Hostname: page-component-7479d7b7d-c9gpj Total loading time: 0 Render date: 2024-07-13T15:41:45.214Z Has data issue: false hasContentIssue false
  • English
  • Français

Properties of a Submicron-Honeycomb thin film

Published online by Cambridge University Press:  16 February 2011

R. C. Furneaux ,
J. S. Crompton  and
D. J. Fitchett
R. C. Furneaux
Affiliation:
Alcan International Limited, Banbury, Oxon, England 0X16 7SP
J. S. Crompton
Affiliation:
Alcan International Limited, Banbury, Oxon, England 0X16 7SP
D. J. Fitchett
Affiliation:
Alcan International Limited, Banbury, Oxon, England 0X16 7SP
Get access

Abstract

A method has been developed of separating the porous film produced by anodizing aluminium from its substrate. Such films have a honeycomb morphology with pores that open at both surfaces. They are composed of essentially anhydrous alumina doped with acid anion from the anodizing electrolyte, and are electron diffraction insensitive. A geometrical model has been developed that describes how the pore morphology is determined by the anodizing voltage. Using this model, expressions are derived that relate cell dimensions to voltage-determined parameters and bulk properties such as porosity.

The flexural modulus and tensile strength of honeycombs have been modelled by considering bending moments experienced by the cell walls. Thus, the properties were expressed in terms of cell dimensions. Here, the anodic film and honeycomb models are combined. These are used to analyze the mechanical properties of the films as determined by the anodizing parameters. A critical crack size is predicted and compared with the results of microstructural examinations. Good agreement is shown. Assumptions behind these findings and the implications arising are discussed.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 188: Symposium K – Thin Films: Stresses and Mechanical Properties II , 1990 , 281
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Furneaux, R.C., Rigby, W.R. and Davidson, A.P., Nature. 337, 147 (1989).Google Scholar
2. Furneaux, R.C. and Thornton, M.C., Brit. Ceram. Proc. 43, 93 (1988).Google Scholar
3. O'Sullivan, J.P. and Wood, G.C., Proc. Roy. Soc. Lond. A317, 511 (1970).Google Scholar
4. Furneaux, R.C., Philpott, R.W. and Jenkins, D.M., Proc. 1st Int. Conf. on Inorganic Membranes, Montpellier, June 1989, p.47.Google Scholar
5. Alvey, C.E., Thompson, G.E. and Wood, G.C., Proc. 10th World Congr. on Metal Finishing, Kyoto, Oct. 1980, p. 275.Google Scholar
6. Bradhurst, D.H. and Leach, J.S.L., Trans. Brit. Ceram. Soc. 62, 793 (1963).Google Scholar
7. Grosskreutz, J.C., Surface Sci. 8, 173 (1967).Google Scholar
8. Grosskreutz, J.C., J. Electrochem. Soc. 116, 1232 (1969).Google Scholar
9. Gibson, L.J. and Ashby, M.F., Cellular Solids: Structure and Properties (Pergamon Press, Oxford, 1988), pp. 69–119.Google Scholar
10. Furneaux, R.C., PhD thesis, Victoria University of Manchester, 1977.Google Scholar
11. Hertzberg, R.W., Deformation and Fracture Mechanics of Engineering Mechanics (J. Wiley, 1983).Google Scholar
12. Richardson, J.A., Wood, G.C. and Sutton, W.H., Thin Solid Films 16, 99 (1973).Google Scholar
13. Thompson, G.E., Proc. 10th World Congr. on Metal Finishing, Kyoto, Oct. 1980, p. 1.Google Scholar
14. Thompson, G.E., Furneaux, R.C. and Wood, G.C., Trans. Inst. Metal Finishing 55, 117 (1977).Google Scholar
15. Zahavi, J., Zangvil, A. and Metzger, M., J. Electrochem. Soc. 125, 438 (1978).Google Scholar
16. Thompson, G.E. and Wood, G.C., J. Electrochem. Soc. 126, 2042 (1979).Google Scholar
17. Thompson, G.E., Furneaux, R.C. and Wood, G.C., Trans. Inst. Metal Finishing 57, 123 (1979).Google Scholar