Hostname: page-component-76fb5796d-wq484 Total loading time: 0 Render date: 2024-04-26T08:50:07.294Z Has data issue: false hasContentIssue false
  • English
  • Français

Preparation and Use of Mosaic Target for the Deposition of Ferroelectric Bismuth Titanate Thin Films

Published online by Cambridge University Press:  15 February 2011

P.K. Ghosh  and
M.E. Azimi
P.K. Ghosh
Affiliation:
Department of Electrical and Computer Engineering, Syracuse University, Link Hall, Syracuse, NY 13244
M.E. Azimi
Affiliation:
Department of Electrical and Computer Engineering, Syracuse University, Link Hall, Syracuse, NY 13244
Get access

Abstract

Ion beam sputter deposition using a Kaufman source is a well-established technique for fabricating thin films. This method has the capability for yielding smooth surfaces and depositing uniform films over a large area. We have used this technique, in the past, with a 5″ diameter target to deposit smooth ferroelectric bismuth titanate (Bi4Ti3O12) films. One of the major obstacles was fabricating the large target with the desired composition. To reduce cost by simplifying the target preparation process we developed a ‘mosaic’ target to deposit ferroelectric Bi4Ti3O12 films. Films were deposited at different substrate temperatures. Measurements show that the post-annealing of the deposited films results in measurable ferroelectric properties and enhanced low field dielectric behavior in the films. The discussion will include the target fabrication, the observed properties of the resultant films, and the effect of the deposition and post-annealing temperatures on the film properties.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 361: Symposium I2 – Ferroelectric Thin Films IV , 1994 , 39
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Cummins, S.E., J. Appl. Phys., Vol. 36, 1958 (1965).Google Scholar
[2] Cummins, S.E. and Cross, L.E., J. Appl. Phys., Vol. 39, 2268 (1968).Google Scholar
[3] Pulvari, C.F. and Dela Paz, A.S., J. Appl. Phys., Vol. 37, 1754 (1966).Google Scholar
[4] Takei, W.J., Formigoni, N.P., and Francombe, M.H., J. Vac. Sci and Tech., Vol. 7, No. 3, 442 (1969).Google Scholar
[5] Wu, S.Y., J. Appl. Phys., Vol. 50, No. 6, 4314 (1979)Google Scholar
[6] Wu, S.Y., Takei, W.J., Francombe, M.H. and Cummins, S.E., Ferroelectrics, Vol. 3, 217 (1972).Google Scholar
[7] Takei, W.J., Wu, S.Y. and Francombe, M.H., J. of Crystal Growth, Vol. 28, 188 (1975).Google Scholar
[8] Ghosh, P.K., Bhalla, A.S. and Cross, L.E., Proceeding of the Sixth IEEE International Symposium on Applications of Ferroelectrics, June 1986.Google Scholar
[9] Ramesh, R., et al. Appl. Phys. Lett., Vol. 57, No. 15, 1505 (1990).Google Scholar
[10] Buhay, H., et al. Appl. Phys. Lett., Vol. 58, No. 14, 1470 (1991).Google Scholar
[11] Azimi, M.E. and Ghosh, P.K., Ferroic Materials: Design Preparation and Charac, Ceramic Transactions, Vol. 43, 55 (1994).Google Scholar
[12] Kimura, T. and Yamaguchi, T., Ceramics Int., Vol. 9, No. 1, 13 (1983).Google Scholar
[13] Xu, J.J., Shaikh, A.S. and Vest, R.W., IEEE Trans. Ultr. Ferro, and Freq. Control, Vol. 36, No. 3, 307 (1989).Google Scholar
[14] Bufoot, J.C., Polar Dielectrics and their Applications, Berkeley: Univ. of Calif. Press, (1979).Google Scholar