Hostname: page-component-848d4c4894-cjp7w Total loading time: 0 Render date: 2024-06-24T23:37:35.486Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructures of Stainless Steels Exhibiting Reduced Friction and Wear After Implantation with Ti and C*

Published online by Cambridge University Press:  25 February 2011

D. M. Follstaedt ,
F. G. Yost  and
L.E. Pope
D. M. Follstaedt
Affiliation:
Sandia National Laboratories, Albuquerque, NM 87185
F. G. Yost
Affiliation:
Sandia National Laboratories, Albuquerque, NM 87185
L.E. Pope
Affiliation:
Sandia National Laboratories, Albuquerque, NM 87185
Get access

Abstract

Implantation of Ti and C into stainless steel discs of Types 304, 15–5 PH, Nitronic 60 and 440C has previously been reported to reduce wear depths by up to ∼ 85% and friction by ∼ 50% in unlubricated pin-on-disc tests. Our earlier studies relating microstructure to friction and wear results in Type 304 are first summarized; these indicate that the improvements in the surface mechanical properties are due to an amorphous surface layer, similar to the amorphous layer observed in pure Fe implanted with Ti and C. We have now examined the other three implanted steels and found similar amorphous layers. These results strongly suggest that the amorphous surface alloy is responsible for reduced friction and wear in all the steels.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 27: Symposium E – Ion Implantation and Ion Beam Processing of Materials , 1983 , 655
Copyright
Copyright © Materials Research Society 1984

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

*

This work performed at Sandia National Laboratories supported by the U. S. Department of Energy under contract #DE-AC04-76DP00789.

References

REFERENCES

1. Pope, L. E., Yost, F. G., Follstaedt, D. M., Knapp, J. A. and Picraux, S. T., in Wear of Materials 1983, Ludema, K. C., ed., (Book No. H00254, ASME, New York, 1983), p. 280;Google Scholar
1a also in Mat. Res. Soc. Symp. Proc. 7, 261–268 (1982).Google Scholar
2. Singer, I. L., Carosella, C. A. and Reed, J. R., Nucl. Inst. and Meth. 182/183, 923 (1981).Google Scholar
3. Carosella, C. A., Singer, I. L., Bowers, R. C. and Gossett, C. R., in Ion Implantation Metallurgy, eds. Preece, C. M. and Hirvonen, J. K. (Met. Soc. of AIME, Warrendale, PA, 1980), p. 103.Google Scholar
4. Fischer, T. E., Luton, M. J., Williams, J. M., White, C. W. and Appleton, B. R., ASLE Trans. 26, 4, 466 (1983).Google Scholar
5. Bolster, R.N. and Singer, I.L., ASLE Trans. 24, 4, 526 (1981);Google Scholar
5a also Singer, I.L., Bolster, R.N. and Carosella, C.A., Thin Sol. Films 73, 283 (1980).Google Scholar
6. Follstaedt, D. M., Knapp, J. A. and Picraux, S. T., Appl. Phys. Lett. 37, 330 (1980);Google Scholar
6a also in Ref. 3, p. 152.Google Scholar
7. Follstaedt, D. M., Pope, L. E., Knapp, J. A., Picraux, S. T. and Yost, F. G., to appear in Thin Solid Films 107, 259 (1983).Google Scholar
8. Follstaedt, D. M., Yost, F. G., Pope, L. E., Picraux, S. T. and Knapp, J. A., Appl. Phys. Lett. 43, 358 (1983).Google Scholar
9. Pearson, W. B., Handbook of Lattice Spacings and Structures of Metals, Vol. 1, (Pergamon Press, New York, 1958) p. 918.Google Scholar
10. Yost, F. G., Picraux, S. T., Follstaedt, D. M., Pope, L. E. and Knapp, J. A., to appear in Thin Solid Films 107.Google Scholar
11. Pope, L. E., Yost, F. G., Follstaedt, D. M., Picraux, S. T. and Knapp, J. A., proceedings this symposium.Google Scholar