Hostname: page-component-7479d7b7d-q6k6v Total loading time: 0 Render date: 2024-07-11T17:30:58.598Z Has data issue: false hasContentIssue false
  • English
  • Français

Mechanical Properties of Boron Doped Si and Si/SiO 2 Membranes

Published online by Cambridge University Press:  01 February 2011

Gabe Kuhn ,
Todd Myers ,
Susmita Bose  and
Amit Bandyopadhyay
Gabe Kuhn
Affiliation:
School of Mechanical and Materials Engineering Washington State University, Pullman, WA 99164-2920.
Todd Myers
Affiliation:
School of Mechanical and Materials Engineering Washington State University, Pullman, WA 99164-2920.
Susmita Bose
Affiliation:
School of Mechanical and Materials Engineering Washington State University, Pullman, WA 99164-2920.
Amit Bandyopadhyay
Affiliation:
School of Mechanical and Materials Engineering Washington State University, Pullman, WA 99164-2920.
Get access

Abstract

In our research, PZT film actuated micro-machined Si substrates are being developed for numerous applications in which membranes are actuated primarily in flexural mode. Silicon wafers, 3-inches in diameter, underwent boron doping in order to act as an etch stop. Approximately 200-nm of SiO2 was grown on the boron-doped side of the wafers. Photolithography and backside etching using EDP resulted in 2-μm thick membranes. Using reactive ion etching (RIE), beam structures resulted from the membranes. Nano-mechanical testing of the beams indicated that there were substantial residual tensile stresses in these structures. Initial calculations reveal a tensile stress of 57.7 MPa in the Si/SiO2 beams. The residual tensile stress subsequently caused the overall beam stiffness to be two orders of magnitude higher than it would be without stress. After stripping the oxide with a buffered oxide etchant (BOE), a residual stress of 26.5 MPa was measured, which is presumably caused from the remaining boron concentration. The aim of this paper is to understand influences of boron doping and processing variables on residual stresses.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 729: Symposium U – MEMS and BioMEMS , 2002 , U3.12
Copyright
Copyright © Materials Research Society 2002

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Leplan, H., Geenen, B., Robic, J. Y., and Pauleau, Y., J. Appl. Phys. 78 (2), 962 (1995).Google Scholar
2. Robic, J. Y., Leplan, H., Pauleau, Y., and Rafin, B., Thin Solid Films. 290-291, 34 (1996).Google Scholar
3. Bhushan, B., Murarka, S. P., and Gerlach, J., J. Vac. Sci. Technol. B. 8(5), 1068 (1990).Google Scholar
4. Blech, I., and Cohen, U., J. Appl. Phys. 53 (6), 4202 (1982).Google Scholar
5. Jaccodine, R. J. and Schlegel, W. A., J. Appl. Phys. 37 (6), 2429 (1966).Google Scholar
6. Schellin, R., Hess, G., Kuhnel, W., Thielemann, C., Trost, D., Wacker, J., and Steinmann, R., Sensors and Actuators A. 41-42, 287 (1994).Google Scholar
7. Temple-Boyer, P., Scheid, E., Faugere, G., and Rousset, B., Thin Solid Films. 310, 234 (1997).Google Scholar
8. Yi, T. and Kim, C. J., Meas Sci. Technol. 10, 706 (1999).Google Scholar
9. Ghandhi, S. K., VLSI Fabrication Principles, Silicon and Gallium Arsenide, 2nd Ed. John Wiley & Sons, Inc. 1994. pp. 19.Google Scholar
10. Roark, R. J., and Young, W. C., Formulas for Stress and Strain, 5th Ed. McGraw-Hill Book Company. 1975. pp. 96–153.Google Scholar
11. Barsoum, M., Fundamentals of Ceramics, McGraw-Hill Companies, Inc. 1997. pp. 402.Google Scholar