Hostname: page-component-84b7d79bbc-rnpqb Total loading time: 0 Render date: 2024-07-29T21:00:49.889Z Has data issue: false hasContentIssue false
  • English
  • Français

Measurement of the Triaxial Stress State of Confined Line Structures During Thermal Cycling

Published online by Cambridge University Press:  25 February 2011

M.A. Moske ,
P.S. Ho ,
D.J. Mikalsen ,
J.J. Cuomo  and
R. Rosenberg
M.A. Moske
Affiliation:
IBM Thomas J. Watson Research Center, Yorktown Heights, NY 10598
P.S. Ho
Affiliation:
IBM Thomas J. Watson Research Center, Yorktown Heights, NY 10598
D.J. Mikalsen
Affiliation:
IBM Thomas J. Watson Research Center, Yorktown Heights, NY 10598
J.J. Cuomo
Affiliation:
IBM Thomas J. Watson Research Center, Yorktown Heights, NY 10598
R. Rosenberg
Affiliation:
IBM Thomas J. Watson Research Center, Yorktown Heights, NY 10598
Get access

Abstract

A method based on the bending beam technique has been developed to measure the mechanical stresses of fine lines confined by a dielectric layer. This method has been employed to determine the thermal stress of AI(2at%Cu) lines passivated by a quartz overlayer between room temperature and 400ºC. The effect of quartz confinement was analyzed by matching the thermal strains at the metal/quartz interfaces and imposing a mechanical equilibrium condition on the structure. The analysis enables us to deduce the triaxial stress components of metal and quartz from measurements of the substrate bending parallel and perpendicular to the length direction of the lines. Results of the measurementshow a substantial stress enhancement as a result of the confinement, with the stress level significantly higher than that of a passivatecd blanket film. The magnitude of the stress depends on the line geometry, the layer deposition conditions and the extent of plastic deformation during thermal cycling. Results of this measurement are consistent with those determined using X-ray techniques.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 203: Symposium D – Electronic Packaging Materials Science V , 1990 , 77
Copyright
Copyright © Materials Research Society 1991

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Yost, F.G. and Campbell, F.E., IEEE, Circuits and Devices 6 (3), 40, (1990).Google Scholar
[2] Dunn, C.F. and McPherson, J.W., IEEE, Proc. Int. Re,. Phys. Symp., p.252,(1990).Google Scholar
[3] Groothuis, S.K. and Schroen, W.H., IEEE, Proc. Int. Rdl. Phys. Synup., p.1, (1987).Google Scholar
[4] Jones, R.E. Jr., and Basehore, M.L., Appl. Phys. Lett. 50, 725, (1987).Google Scholar
[5] Tezaki, A., Mineta, T., Egawa, H. and Noguchi, T., IEEE, Proc. IRPS, p.221, (1990).Google Scholar
[6] Korhonen, M., Paszkiet, C., Black, R.D. and Li, C.Y., Scripta Met. 24, 2297, (1990).Google Scholar
[7] Chen, S.T., Yang, C.H., Faupel, F. and Ho, P.S., J. Appl. Phys. 64, 6690, (1988).Google Scholar
[8] Sinha, A.K. and Sheng, T.T., Thin Solid Films 48, 117, (1978).Google Scholar
[9] Amer. Inst. of Phys. Handbook, ed. by GFay, E.D., McGraw Hill, New York (1972).Google Scholar
[10] Gardner, D.S. and Flinn, P.A., Mat. Res. Soc. Proc. 130, 69, (1989).Google Scholar
[11] Sinha, A.K., Levinstein, H.J. and Smith, T.E., J. Appl. Pys. 49, 2423, (1978).Google Scholar
[12] Doerner, M.F. and Nix, W.D., CRC 14,225 (1988).Google Scholar
[13] Feng, Z.C. and Liu, H.D., J. Appl. Pfiys. 54,83(1983).Google Scholar
[14] Moske, M. and Ho, P.S., to be published.Google Scholar