Hostname: page-component-848d4c4894-8bljj Total loading time: 0 Render date: 2024-06-17T15:35:07.305Z Has data issue: false hasContentIssue false
  • English
  • Français

Laminates From The Soy-Based Polyurethanes and Natural and Synthetic Fibers

Published online by Cambridge University Press:  14 March 2011

Zoran S. Petrovič ,
Wei Zhang ,
Ivan Javni  and
Andrew Guo
Zoran S. Petrovič
Affiliation:
Kansas Polymer Research Center, Pittsburg State University, Pittsburg, KS 66762
Wei Zhang
Affiliation:
Kansas Polymer Research Center, Pittsburg State University, Pittsburg, KS 66762
Ivan Javni
Affiliation:
Kansas Polymer Research Center, Pittsburg State University, Pittsburg, KS 66762
Andrew Guo
Affiliation:
Kansas Polymer Research Center, Pittsburg State University, Pittsburg, KS 66762
Get access

Abstract

Two polyols were prepared from soybean oil, one by epoxidation route and the other via hydroformylation. The polyol obtained by epoxidation has secondary groups and has a gel time of more than one hour when reacted with crude MDI to produce polyurethanes. Hydroformylated polyol has a gel time with MDI of several minutes and is more suitable for reinforced reaction injection molding (RRIM). The first group of polyurethanes had a glass transition close to 80 °C while the hydroformylated gave about 30 degrees lower Tg and comparable strength but higher elongation. Adding glycerin as the crosslinker could increase both Tg and strength. Two series of laminates were prepared using several types of glass fabric, carbon fiber, polyester, cotton and jute fabrics r as reinforcements. Hydroformylated polyol based polyurethane composites were softer, with lower Tg, modulus and strength. Composites with organic fibers were lighter and more flexible than the glass reinforced samples. For comparison glass reinforced epoxy and polyester were prepared and tested. Organic fibers gave lower stiffness and strength than the corresponding glass or carbon fiber. Although the neat polyester and epoxy resins had somewhat higher strengths than the polyurethanes from soybean oil, mainly due to the higher crosslinking density, the composites from the soy oil-based resin displayed comparable or better properties. Glass transition and mechanical properties of the soy-based polyurethanes was varied from about 70 °C to 140 °C with added crosslinkers. Processing time of the soy-polyurethanes resins was shorter than that of the other two resins.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 702: Symposium U – Advanced Fibers, Plastics, Laminates and Composites , 2001 , U4.5.1
Copyright
Copyright © Materials Research Society 2002

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Guo, A., Javni, I., and Petrovic, Z., J. Appl. Polym. Sci. 77, 467–73 (2000).Google Scholar
2. Guo, A., Javni, I., and Petrovic, Z., “Development of polymeric materials from soybean oil,” Abstr. of the 89th AOCS Annual Meeting & Expo, 50 (1998).Google Scholar
3. Petrovic, Z., Guo, A., and Javni, I., US.Pat.#6,107,433 (Aug.2000).Google Scholar
4. Petrovic, Z.S., Javni, I., and Guo, A., “Electroinsulating polyurethane casting resins based on soy oil and castor oil,” Proceedings of the Polyurethanes EXPO'98, 559–62 (1998).Google Scholar
5. Guo, A., Javni, I., and Petrovic, Z., ACS PMSE Preprints, 80, 503–4 (1999).Google Scholar
6. Javni, I., Petrovic, Z.S., Guo, A., and Fuller, R., J. Appl. Polym. Sci., accepted (1999).Google Scholar
7. Petrovic, Z.S., Guo, A., Fuller, R., and Javni, I., “Thermosetting resins from vegetable oils,” SPE Technical Papers Volume 45 (ANTEC'99), 888–91 (1999).Google Scholar
8. American Institute of Chemical Engineers, “Composite created from soybean oil,” Chem. Eng. Prog., 93, 19–20 (1997).Google Scholar
9. Crivello, J.V., Sternstein, S.S., and Narayan, R., “Mechanical characterization of glass fiber reinforced/UV cured resins from epoxidized linseed oil,” Proc. of the 1995 ASME Int. Mech. Eng. Congress and Expo. Part 1, 69–1, 175–80 (1995).Google Scholar
10. Crivello, J.V., Narayan, R., and Sternstein, S.S., J. Appl. Polym. Sci., 64, 2073–87 (1997).Google Scholar
11. Dahlke, B., Poltrock, R., Larbig, H., and Scherzer, H.D., J. Cell. Plast., 34, 361–79 (1998).Google Scholar
12. Materials Research Society, “Chemically modified soy oil replaces conventional resins in composite manufacturing processes,” MRS Bulletin, 23, 6 (1998).Google Scholar
13. United Soybean Board, “Deere Testing Reinforced Soy Plastics,” Feedstocks, 2, 2 (1998).Google Scholar
14. Warth, H., Muelhaupt, R., Hoffmann, B., and Lawson, S., Angew. Makromol. Chem., 249, 79–92 (1997).Google Scholar
15. Crivello, J.V. and Carlson, K.D., Macrom. Reports, 33, 251–62 (1996).Google Scholar
16. Crivello, J.V. and Narayan, R., Chem. Mater., 4, 692–9 (1992).Google Scholar
17. I. Ray Publishing, “Expanding applications reinforce the value of composites,” High Performance Composites, 5, 10–25 (1997).Google Scholar