Hostname: page-component-77c89778f8-rkxrd Total loading time: 0 Render date: 2024-07-17T17:04:46.505Z Has data issue: false hasContentIssue false
  • English
  • Français

In-Situ Tem-Investigation of Stress- and Electromigration- Induced Void Formation and Growth in Passivated Al-Interconnects

Published online by Cambridge University Press:  10 February 2011

Dirk Heinen  and
Herbert Schroeder
Dirk Heinen
Affiliation:
Institut für Festkörperforschung, Forschungszentrum Jülich GmbH, D-52425 Jülich, Germany
Herbert Schroeder
Affiliation:
Institut für Festkörperforschung, Forschungszentrum Jülich GmbH, D-52425 Jülich, Germany
Get access

Abstract

In-situ TEM observations on void formation and growth have been performed in passivated Al-lines in order to collect detailed microstructural data such as void number density, void size distribution, and growth rates as a basis for modelling stress relaxation and electromigration (EM) effects.

The samples were 0.5mm long lines of 200nm thick Al with different widths (0.8, 1.6 and 2.4μm) passivated with 200μm thick SiNx. Additional experimental parameters were average grain size (0.5μm to more than 3μm, i.e. nearly perfect bamboo structure in the lines), relaxation time (0.1 to 20h) and temperature (20 – 300°C) and electromigration current density (without current up to ∼2MA/cm2).

Measurements without current reveal that stress induced voids

– develop after a temperature step of 50°C during cooling from 450°C and above. Upon heating from RT they start shrinking at 150°C and disappear completely at 350°C.

– decrease in number and total relative volume but have constant mean void size with increasing number n of temperature cycles (n < 4)

– show a strong dependence of their total relative volume on the microstructure (grain size, bamboo structure) which is strongly dependent on the anealing temperature for T ≥450° C.

– show growth rates during isothermal annealing which are very dependent on relaxation time and temperature.

Additional measurement with an applied electrical current, i.e. during an EM-test, show that nearly all the preexisting stress-induced voids

– change their shapes and positions. This is dependent on electrical current density and time. Their frequently observed motion along the line (against the electron wind) was not neccessarily stopped by so-called blocking grains, i.e. grains without boundaries parallel to the line.

– slightly change their total number but nearly maintain their total relative volume which is independent of current density or time.

The collected statistical microstructural data are in good agreement with macroscopic stress relaxation results by wafer curvature and X-ray diffraction and recent in-situ stress measurement during an EM-test.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 473: Symposium J – Materials Reliability in Microelectronics VII , 1997 , 381
Copyright
Copyright © Materials Research Society 1997

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Flinn, P.A., Mat. Res. Soc. Symp., 130, (1989), 41 Google Scholar
[2] Witvrouw, A., Proost, J., Deweerdt, B., Roussel, Ph. and Maex, K., Mat. Res. Soc. Symp., 356, (1995), 441 Google Scholar
[3] Flinn, P.A., Mack, A., Besser, P. and Marieb, T., MRS Bulletin, 18, No. 12, (1993), 26 Google Scholar
[4] Venkatraman, R., Besser, T. R., Brennan, S., Bravman, J., Mat. Res. Soc. Symp., 239, (1992), 227 Google Scholar
[5] Burges, U., Eppler, I., Schilling, W., Schroeder, H., Trinkaus, H., Proc. of Third Int. Workshop on “Stress-induced Phenomena in Metallization” Stanford (USA), AIP Conf. Proc., 373, (1995), 3Google Scholar
[6] Eppler, I., Schroeder, H., Burges, U., Schilling, W., Mat. Res. Soc. Symp., 436, (1996)Google Scholar
[7] Flinn, P.A., Madden, M.C., Marieb, T.N., MRS Bulletin, (June 1994), 51 Google Scholar
[8] Riege, S.P., Hunt, A.W., Prybyla, J.A., Mat. Res. Soc. Symp., 391, (1995), 249 Google Scholar
[9] Heinán, D., Schroeder, H., Schilling, W., This volumeGoogle Scholar
[10] Burges, U., Doctoral Thesis, RWTH-Aachen, Germany (1995)Google Scholar
[11] Beckers, D., Doctoral Thesis, RWTH-Aachen, Germany (1996)Google Scholar
[12] Beckers, D., Schroeder, H., Eppler, I., Burges, U., Hönings, J., Schilling, W., Mat. Res. Soc. Symp., 436, (1996)Google Scholar
[13] Hönings, J., Diploma Thesis, RWTH-Aachen, Germany (1995)Google Scholar
[14] Roths, C., Hönings, J., Schroeder, H. and Schilling, W., This volumeGoogle Scholar
[15] Korhonen, M.A., Børgesen, P., Brown, D.D., Li, C.-Y., MRS Symp. Proc, 309, (1993), 121 Google Scholar
[16] Korhonen, M.A., Børgesen, P., Brown, D.D., Li, C.-Y., Sullivan, T.D., Totta, P.A., 2nd Workshop on “Stress-induced Phenomena in Metallization” Austin (USA), (1993), 15 Google Scholar