Hostname: page-component-848d4c4894-pjpqr Total loading time: 0 Render date: 2024-06-22T06:15:01.926Z Has data issue: false hasContentIssue false
  • English
  • Français

Exploring Failure Mechanisms of Lubricated 52100 Steel Contacts in High Vacuum and Dry Air

Published online by Cambridge University Press:  28 February 2011

Michael T. Dugger  and
Yip-Wah Chung
Michael T. Dugger
Affiliation:
Department of Materials Science and Engineering and Center for Engineering Tribology, Northwestern University, Evanston, IL 60208
Yip-Wah Chung
Affiliation:
Department of Materials Science and Engineering and Center for Engineering Tribology, Northwestern University, Evanston, IL 60208
Get access

Abstract

A vacuum chamber was designed for studying tribological properties of materials under pressures of 5xlO8 Torr to one atmosphere. The chamber is equipped with a pin-on-disk tribometer, in-situ Auger\X-ray photoelectron spectroscopies, a sputter-ion gun and a windowless solid-state X-ray detector. In this paper, we present results of a study using 52100 steel balls sliding on flat disks of the same material in vacuum and in dry air as a function of normal load. The contacts were lubricated with a synthetic hydrocarbon oil (poly-a-olefin). Failure is defined as the point at which the coefficient of friction increases rapidly above the steady state value.

As expected, failure occurs much sooner in vacuum than in dry air. Surface analysis (Auger and XPS) shows direct evidence of the occurrence of high temperature flashes on the surface, which allows the formation and maintenance of a thick oxide in the presence of an adequate supply of oxygen. In addition, a brown film is formed in the vicinity of the wear track for tests performed in dry air, while this film is absent in vacuum. The brown film appears to be a combination of iron oxide and oxidized hydrocarbon from XPS measurements. Results of these studies suggest that the maintenance of an oxide is associated with extended contact life in these studies.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 140: Symposium S – New Materials Approaches to Tribology: Theory and Applications , 1988 , 423
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Shen, Y.S., PhD thesis, Pennsylvania State University, 1982.Google Scholar
2. Lim, S.C. and Ashby, M.F., Acta. Metall. 35, 1 (1987).Google Scholar
3. Lim, S.C., Ashby, M.F., and Brunton, J.H., Acta. Metall. 35, 1343 (1987).Google Scholar
4. Timoshenko, S. and Goodier, J.N., Theory of Elasticity (McGraw-Hill, New York, 1951).Google Scholar
5. Greenwood, J.A. and Williamson, J.P.B., Proc. Roy. Soc. Lond. A295, 300 (1966).Google Scholar
6. Stinton, H.C., Spikes, H.A., and Cameron, A., ASLE Trans. 25, 355 (1982).Google Scholar
7. Ali, A., Lockwood, F., Klaus, E.E., Duda, J.L., and Tewksbury, E.J., ASLE Trans. 22, 267 (1979).Google Scholar
8. Cho, L. and Klaus, E.E., ASLE Trans. 24, 119 (1981).CrossRefGoogle Scholar
9. Lockwood, F.E. and Klaus, E.E., ASLE Trans. 24, 276 (1981).Google Scholar
10. Lockwood, F.E. and Klaus, E.E., ASLE Trans. 25, 236 (1982).Google Scholar
11. Lahijani, J., Lockwood, F.E., and Klaus, E.E., ASLE Trans. 25, 25 (1982).Google Scholar
12. Pan, F.M. and Stair, P.C., J. Vac. Sci. Technol. A5, 1036 (1987).Google Scholar
13. Rhodes, K.L. and Stair, P.C., J. Vac. Sci. Technol. A6, 971 (1988).Google Scholar
14. Archard, J.F. and Kirk, M.T., Proc. Roy. Soc. 261A, 532 (1961).Google Scholar
15. Archard, J.F. and Cowking, E.W., Proc. Inst. Mech. Engrs. 180, Pt.3B, 47 (1965/1966).Google Scholar
16. Gohar, R., J. Lub. Tech. 93, 371 (1971).Google Scholar