Hostname: page-component-848d4c4894-v5vhk Total loading time: 0 Render date: 2024-06-19T02:57:54.917Z Has data issue: false hasContentIssue false
  • English
  • Français

Etch Characteristics of GaN Using Inductively Coupled Cl2/HBr and Cl2/Ar Plasmas

Published online by Cambridge University Press:  10 February 2011

H. S. Kim ,
Y. J. Lee ,
Y. H. Lee ,
J. W. Lee ,
M. C. Yoo ,
T. I. Kim  and
G. Y. Yeom
H. S. Kim
Affiliation:
Department of Materials Engineering, Sung Kyun Kwan University, Suwon, 440–746, Korea
Y. J. Lee
Affiliation:
Department of Materials Engineering, Sung Kyun Kwan University, Suwon, 440–746, Korea
Y. H. Lee
Affiliation:
Department of Materials Engineering, Sung Kyun Kwan University, Suwon, 440–746, Korea
J. W. Lee
Affiliation:
Photonics Lab., Samsung Advanced Institute of Technology, Suwon, 440–600, Korea
M. C. Yoo
Affiliation:
Photonics Lab., Samsung Advanced Institute of Technology, Suwon, 440–600, Korea
T. I. Kim
Affiliation:
Photonics Lab., Samsung Advanced Institute of Technology, Suwon, 440–600, Korea
G. Y. Yeom
Affiliation:
Department of Materials Engineering, Sung Kyun Kwan University, Suwon, 440–746, Korea
Get access

Abstract

To fabricate GaN-based optoelectronic devices successfully, a reproducible etch process with high etch rates, vertical etch profile, and damage-free surface is required. In this study, GaN etching was performed using planar inductively coupled plasmas and the effects of process parameters such as inductive power, bias voltage, pressures and, gas combination on the characteristics of the plasmas were studied using Langmuir probe, optical emission spectroscope (OES), and quadrupole mass spectrometer (QMS). Gas combinations of Cl2/Ar and Cl2/HBr were used to etch GaN. GaN etch rates increased with the increase of chlorine radical and ion energy (bias voltage), and the etch rates close to 4000 Å/min could be obtained without substrate heating over 100 °C. The addition of HBr and Ar (more than 20%) generally reduced GaN etch rates. In our experimental condition, it appears that the chemical reaction between Cl and Ga in GaN affects more significantly to GaN etching compared to physical sputtering, and it was partially confirmed by the data measured by Langmuir probe and OES. Angle resolved XP S data showed the variation of surface Ga/N ratio depending on the process parameters, which influence the formation of low resistance ohmic contact.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 468: Symposium D – Gallium Nitride and Related Materials II , 1997 , 367
Copyright
Copyright © Materials Research Society 1997

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Zolper, J.C. and Shul, R. J., MRS BULLETIN/FEBRUARY, p36 (1997).Google Scholar
2. Vartuli, C. B., Pearton, S. J., Abernathy, C. R., Shul, R. J., Howard, A. J., Kilcoyne, S. P., Parmeter, J. E., and Hagerott-Crawford, M., J. Vac. Sci. Technol. A 14, 1011 (1996).Google Scholar
3. Pearton, J., Vartuli, C. B., Shul, R. J., and Zolper, J. C., Materials Sci. Eng. B31, 1 (1995).Google Scholar
4. Shul, J., McClellan, G. B., Pearton, S. J., Abernathy, C. R., Constantine, C., and Barratt, C., Electron. Lett. 32, 1408 (1996).Google Scholar
5. Ping, T., Schmitz, A. C., Asif Khan, M., and Adesida, I., J. Electron. Mat. 25, 825 (1996).Google Scholar
6. Adesia, I., Ping, A. T., Youtsey, C., and Dow, T., Khan, M., Olson, D. T., and Kuznia, J. N., Appl. Phys. Lett. 65, 889 (1994).Google Scholar
7. Nakamura, , Senoh, M., Nagahama, S. I., Iwasa, N., Yamada, T., Matsushita, T., Kiyoku, H. and sugimoto, Y., Jpn. J. Appl. Phys. 35, L74 (1996).Google Scholar
8. Donnelly, M., J. Vac. Sci. Technol. A 14, 1076 (1996).Google Scholar
9. Ping, A. T., Adesia, I., Khan, M., and Kuznia, J. N., Electron. Lett. 30, 1895 (1994).Google Scholar