Hostname: page-component-7479d7b7d-q6k6v Total loading time: 0 Render date: 2024-07-12T03:51:43.406Z Has data issue: false hasContentIssue false
  • English
  • Français

Effects of buried insulator-sensor interface on the lateral conduction of high fill factor aSi:H imagers

Published online by Cambridge University Press:  17 March 2011

M. Mulato ,
F. Lemmi ,
S. E. Ready ,
J. P. Lu ,
K. Van Schuylenbergh ,
R. A. Street ,
J. Ho ,
R. Lau  and
J. B. Boyce
M. Mulato
Affiliation:
Xerox Palo Alto Research Center, 3333 Coyote Hill Road, Palo Alto, CA
F. Lemmi
Affiliation:
Xerox Palo Alto Research Center, 3333 Coyote Hill Road, Palo Alto, CA
S. E. Ready
Affiliation:
Xerox Palo Alto Research Center, 3333 Coyote Hill Road, Palo Alto, CA
J. P. Lu
Affiliation:
Xerox Palo Alto Research Center, 3333 Coyote Hill Road, Palo Alto, CA
K. Van Schuylenbergh
Affiliation:
Xerox Palo Alto Research Center, 3333 Coyote Hill Road, Palo Alto, CA
R. A. Street
Affiliation:
Xerox Palo Alto Research Center, 3333 Coyote Hill Road, Palo Alto, CA
J. Ho
Affiliation:
Xerox Palo Alto Research Center, 3333 Coyote Hill Road, Palo Alto, CA
R. Lau
Affiliation:
Xerox Palo Alto Research Center, 3333 Coyote Hill Road, Palo Alto, CA
J. B. Boyce
Affiliation:
Xerox Palo Alto Research Center, 3333 Coyote Hill Road, Palo Alto, CA
Get access

Abstract

The pixel cross-talk is investigated in two-dimensional amorphous silicon (a-Si:H) imager arrays based on the new high fill factor design. In this configuration a continuous a-Si:H sensor extends over the whole surface of the imager, and a buried insulator material with low dielectric constant is used to separate the sensor from the underlying active matrix readout circuit. We find that the lateral conduction between neighboring pixels is mainly determined by the quality of the buried insulator-sensor interface, rather than the specific buried material itself. Minimum cross-talk values below 1% are obtained for different insulator materials including silicon oxynitride and thicker polymer based resins. The quality of this interface also affects trapping and recombination of the photogenerated carriers, influencing important imager properties such as sensitivity and image lag.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 609: Symposium A – Amorphous & Heterogeneous Silicon Thin Films – 2000 , 2000 , A12.8
Copyright
Copyright © Materials Research Society 2000

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Rahn, J. T., Lemmi, F., Weisfield, R. L., Lujan, R., Mei, P., Lu, J. P., Ho, J., Ready, S. E., Apte, R. B., Nylen, P., Boyce, J., and Street, R. A., Proc. of SPIE Conference on Physics of Medical Imaging 3659, San Diego, CA, Feb. 1999, p. 510.Google Scholar
2. Rahn, J. T., Lemmi, F., Mei, P., Lu, J. P., Boyce, J. B., Street, R. A., Apte, R. B., Ready, S. E., Schuylenbergh, K. F. Van, Nylen, P., Ho, J., Fulks, R. T., Lau, R., and Weisfield, R., MRS Symp. Proc. 557, 809, 1999.Google Scholar
3. Mulato, M., Lemmi, F., Lau, R., Lu, J. P., Ho, J., Ready, S. E., Rahn, J. T., and Street, R. A., Proc. of SPIE Conference on Physics of Medical Imaging 3977, San Diego, CA, Feb. 2000, (in press).Google Scholar
4. Lemmi, F., Rahn, J. T., and Street, R.A., Proc. 18th International Conference on Amorphous and Microcrystalline Semiconductors, Snowbird, UT, Aug.1999, Journal of Non-Crystalline Solids (in press).Google Scholar
5. Street, R. A., ‘Large Area Image Sensor Arrays’, in Technology and Applications of Amorphous Silicon, Editor Street, R.A., Springer Series in Materials Science 37, Springer-Verlag, Berlin, 2000, chapter 4, p.169.Google Scholar
6.BCB is a polymer-based CYCLOTENE Resin from The Dow Chemical Company, which is derived from B-staged bisbenzocyclobutene (BCB) monomers.Google Scholar
7.Kodak manufactured phosphor screen with phosphor density of 34 mg/cm2.Google Scholar