Hostname: page-component-848d4c4894-8bljj Total loading time: 0 Render date: 2024-06-16T16:06:05.506Z Has data issue: false hasContentIssue false
  • English
  • Français

The Effect of Stress on the Nanomechanical Properties of Au Surfaces

Published online by Cambridge University Press:  15 February 2011

J. E. Houston
J. E. Houston*
Affiliation:
Sandia National Laboratories Albuquerque, NM 87185–1413
Get access

Abstract

Stress in thin films plays a critical role in many technologically important areas. The role is a beneficial one in strained layer superlattices where semiconductor electrical and optical properties can be tailored with film stress. On the negative side, residual stress in thin-film interconnects in microelectronics can lead to cracking and delamination. In spite of their importance, however, surface and thin-film stresses are difficult to measure and control, especially on a local level. In recent studies, we used the Interfacial Force Microscope (IFM) in a nanoindenter mode to survey the nanomechanical properties of Au films grown on various substrates. Quantitative tabulations of the indentation modulus and the maximum shear stress at the plastic threshold showed consistent values over individual samples but a wide variation from substrate to substrate. These values were compared with film properties such as surface roughness, average grain size and interfacial adhesion and no correlation was found. However, in a subsequent analysis of the results, we found consistencies which support the integrity of the data and point to the fact that the results are sensitive to some property of the various film/substrate combinations. In recent measurements on two of the original substrate materials we found a direct correlation between the nanomechanical values and the residual stress in the films, as measured globally by a wafer warping technique. In the present paper, we review these earlier results and show recent measurements dealing with stresses externally applied to the films which supports our earlier conclusion concerning the role of stress on our measurements. In addition, we present very recent results concerning morphological effects on nanomechanical properties which add additional support to the suggestion that near-threshold indentation holds promise of being able to measure stress on a very local level

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 440: Symposia CA – Structure and Evolution of Surfaces , 1996 , 177
Copyright
Copyright © Materials Research Society 1997

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Joyce, S. A., Thomas, R. C., Houston, J. E., Michalske, T. A. and Crooks, R. M., Phys. Rev. Lett. 68, 2790 (1992).Google Scholar
2. Thomas, R. C.,. Houston, J. E.,. Michalske, T. A. and Crooks, R. M., Science 259, 1883 (1993).Google Scholar
3. Tangyunyong, P., Thomas, R. C., Houston, J. E., Michalske, T. A., Crooks, R. M. and Howard, A. J., Phys. Rev. Lett. 71, 3319 (1993).Google Scholar
4. Tangyunyong, P., Thomas, R. C., Houston, J. E., Michalske, T. A., Crooks, R. M. and Howard, A. J., J. Adhes. Sci. Technol. 8, 897 (1994).Google Scholar
5. Timoshenko, S. P. and Goodier, J. N., Theory of Elasticity, McGraw-Hill, New York (1970), Chapt. 12.Google Scholar
6. Houston, J. E., Franklin, G. E. and Michalske, T. A. (In preparation).Google Scholar
7. See, for example: Hertzberg, R. W., Deformation and Fracture Mechanics of Engineering Materials, John Wiley and Sons, New York 1989, Chap. 2.Google Scholar
8. Pharr, G. M., Tsui, T. Y., Boshakov, A. and Oliver, W. C., Mat. Res. Soc. Proc. 338, 127 (1994).Google Scholar
9. Flexus, Inc., Sunnyvale, CA.Google Scholar
10. Digital Instruments Inc, 520 E. Montecito St. Santa Barbara, CA 93103.Google Scholar
11. Jarausch, K. F., Houston, J. E. and Russell, P. E. (In Preparation).Google Scholar
12. Hwang, R. Q., Kiely, J. D. and Houston, J. E. (In Preparation).Google Scholar
13. A program modification of the “Shoescan” STM softwary by B. S. Swartzentruber of Sandia National Laboratories.Google Scholar
14. See, for example: Alerhand, O. L., Vanderbilt, D., Meade, R. D. and Joannopoulos, J. D., Phys. Rev. Lett. 61, 1973 (1988); B. S. Swartzentruber, N. Kitamura, M. G. Lagally and M. B. Webb, Phys. Rev. B 47, 13432 (1993).Google Scholar