Hostname: page-component-7479d7b7d-qs9v7 Total loading time: 0 Render date: 2024-07-12T19:31:47.567Z Has data issue: false hasContentIssue false
  • English
  • Français

A Tribological Study of Mo/Al2O3 in Sliding Contact

Published online by Cambridge University Press:  28 February 2011

Hyun-Soo Hong  and
Ward O. Winer
Hyun-Soo Hong
Affiliation:
George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0405
Ward O. Winer
Affiliation:
George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0405
Get access

Abstract

This is Part II of a tribological study of metal/ceramic pair in a sliding contact. The tribological behavior of molybdenum against a single crystal A12O3 was investigated at bulk temperatures of 23ºC and 400ºC using a sliding speed of 4 m/s and loads from nine to twenty five Newtons. The role of oxidational wear was confirmed at both temperatures. The linear dependency of wear rate on load was identified at 23ºC tests. At 400ºC, there was a rapid increase of wear rate at a load of about 25 N possibly due to the volatilization of MoO3, which is the limitation of molybdenum oxide as a solid lubricant. However, this study showed that the out-of-contact oxide formation may have prevented the catastrophic oxidation during contact at the real area of contact. It also showed that in-situ formed molybdenum oxide has good lubricating properties (≃ 0.3) and a low wear rate (≃ 10-14 m3/m). Therefore, this molybdenum can be used for a large range of sliding speeds and loads.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 140: Symposium S – New Materials Approaches to Tribology: Theory and Applications , 1988 , 301
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Bhushan, B. and Sibley, L.B., ASLE Trans., 25, 417 (1982).Google Scholar
2. Akazawa, M., Kato, K., and Umeya, K., Wear, 110, 285 (1986).Google Scholar
3. Aronov, V. and Mesyef, T., J.Trib., 108, 16 (1986).Google Scholar
4. Ceramics in Advanced Energy Technologies, D. Reidel Publishing Co., 1984.Google Scholar
5. Advanced Ceramic Materials -Technological and Economic Assessment, Noyes Publication, 1984.Google Scholar
6. A Review of the State of the Art and Projected Technologies of Low Heat Rejection Engines, National Academy Press, 1987.Google Scholar
7. Winer, W.O., Wear, 10, 422 (1967).Google Scholar
8. Spalvins, T., ASLE Proceedings - 3rd International Conference on Solid Lubrication, 201 (1984).Google Scholar
9. Lancaster, J.K., J. Trib., 16, 221 (1987).Google Scholar
10. Fleischauer, P.D. and Bauer, R., ASLE Trans., 30, 160 (1987).Google Scholar
11. Lankford, J. and Wei, W., NASA CR-179475, 1987.Google Scholar
12. Hong, H. and Winer, W.O., J.Trib., ASME No. 88-Trib-48.Google Scholar
13. Sutor, P., Ceram. Eng. Sci. Proc., 5, 460 (1984).Google Scholar
14. Sliney, H.E., Trib. Inter., 13, 303 (1980).Google Scholar
15. Barry, H.F., Lubr. Eng., 33, 475 (1977).Google Scholar
16. Gardos, M.N., Trib. Trans., L1, 214 (1988).Google Scholar
17. Peterson, M.B., Florek, J.J., and Lee, R.E., ASLE Trans., 2, 101 (1960).Google Scholar
18. Lansdown, A.R., Lubrication, 1st ed. (Pergamon Press, Oxford, 1982), p. 138.Google Scholar
19. Smith, A.F., Wear, 96, 301 (1984).Google Scholar
20. Wilson, J.E., Stott, F.H., and Wood, G.C., R. Soc. Lond., A369, 557 (1980).Google Scholar
21. Jones, E.S., Mosher, J.F., Speiser, R., and Spretnak, J.W., Corrosion, 14, 20 (1958).Google Scholar
22. Kubashewski, O. and Hopkins, B.E., Oxidation of Metals and Alloys, 2nd Ed. (Butterworths, London, 1962), p. 225.Google Scholar