Hostname: page-component-848d4c4894-m9kch Total loading time: 0 Render date: 2024-04-30T15:34:31.297Z Has data issue: false hasContentIssue false
  • English
  • Français

Deposition and Characterization of Metalorganic Chemical Vapor Deposition ZrO2 Thin Films Using Zr(Thd)4

Published online by Cambridge University Press:  15 February 2011

Jie Si ,
Chien H. Peng  and
Seshu B. Desu
Jie Si
Affiliation:
Department of Materials Engineering, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061.
Chien H. Peng
Affiliation:
Department of Materials Engineering, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061.
Seshu B. Desu
Affiliation:
Department of Materials Engineering, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061.
Get access

Abstract

Excellent quality ZrO2 thin films were successfully deposited on single crystal silicon wafers by metalorganic chemical vapor deposition (MOCVD) at reduced pressures using tetrakis(2,2,6,6—tetramethyl—3,5—heptanedionato) zirconium, [Zr(thd)4]. For substrate temperatures below 530°C, the film deposition rates were very small (≤ 1 nm/min). The film deposition rates were significantly affected by: (1) source temperature, (2) substrate temperature, and (3) total pressure. As—deposited films are stoichiometric (Zr/O = 1/2) and carbon free. Furthermore, only the tetragonal ZrO2 phase was identified in as—deposited films. The tetragonal phase transformed progressively into the monoclinic phase as the films were subjected to high temperature post—deposition annealing. The optical properties of the ZrO2 thin films as a function of wavelength, in the range of 200 nm to 2000 nm, are reported. The measured value of the dielectric constant of the as—deposited ZrO2 films is around 19 in the frequency range of 5 kHz to 1000 kHz.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 250: Symposium R – Chemical Vapor Deposition of Refractory Metals and Ceramics II , 1991 , 323
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Krishna, M. Ghanashyam, Rao, K. Narasimha, and Mohan, S., Appl. Lett. 57(6), 557(1990).Google Scholar
2. Deshpandey, C. and Holland, L. in Proceedings of the 7th International Conference on Vacuum metallurgy, Iron Steel Institute of Japan, Tokyo, 1, 276(1982).Google Scholar
3. Tauber, R. N., Dumbri, A. C., and Caffrey, R.E., J. Electrochem. Soc., 118, 747(1971).Google Scholar
4. Desu, S. B., Tian, S., and Kwok, C. K., Mat. Res. Soc. Symp. Proc., 168, 349(1990)Google Scholar
5. Kwok, C. K. and Aita, C. R., J. Appl. Phys. 66(6), 2756(1989).Google Scholar
6. Farabaugh, E. N., Feldman, A., Sun, J., and Sun, Y. N., J. Vac. Sci. Technol. A 5(4), 1671 (1987).Google Scholar
7. Harrop, P. J. and Wankiyn, J. N., Brit. J. Appl. Phys., 18, 739 (1967).Google Scholar
8. Manifacier, J. C., Gasiot, J., and Fillard, J. P., J. Phys. E: Sci. Instrum., 9, 1002 (1976).Google Scholar