Hostname: page-component-84b7d79bbc-tsvsl Total loading time: 0 Render date: 2024-07-26T17:44:07.567Z Has data issue: false hasContentIssue false
  • English
  • Français

Crack Dynamics and Grain Size

Published online by Cambridge University Press:  15 February 2011

John J. Gilman
John J. Gilman*
Affiliation:
UCLA, Department of Materials Science and Engineering, Boelter Hall, Los Angeles, CA 90024
Get access

Abstract

Two aspects of fast cracks are considered: 1. the terminal velocity, and corresponding relative kinetic energy; 2. the grain size dependence of the fracture. It is argued that this is determined by the kinetic energies of cracks when they have expanded enough to reach the boundaries of the grains in which they lie. This is more consistent with the observed facts than the more usual quasi-static models.

By considering the limiting conditions at the very tip of a moving crack, many complications are avoided in calculating the terminal velocity. The maximum transverse acceleration of material is limited by the maximum stress (cohesive) that can be applied. The resulting terminal velocity is: 0.4 vs, where vs is the longitudinal sound speed; compared with measured values which average about: 0.31 vs.

In polycrystals, microcracks are found when the applied stress exceeds the yield stress. However, the microcracks do not propagate in fine-grained specimens because they do not have enough kinetic energy to cross a typical grain boundary. This leads to the observed dependence of the fracture stress on the grain size.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 362: Symposium J – Grain-Size and Mechanical Properties--Fundamentals and Applications , 1994 , 91
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Lawn, B., Fracture of Brittle Solids - Second Edition, Cambridge University Press (1993).Google Scholar
2. Mott, N. F., Engineering, 165, 16 (1948).Google Scholar
3. Dulaney, E. N. and Brace, W. F., J. Appl. Phys., 31, 2233 (1960).Google Scholar
4. Marder, M., Physica D, 66, 125 (1993).Google Scholar
5. Stroh, A. N, Adv. Phys., 6, 418 (1957).Google Scholar
6. Gilman, J. J., J. Appl. Phys., 27, 1262 (1956).Google Scholar
7. Fineberg, J., Gross, S. P., Marder, M., and Swinney, H. L., Phys. Rev. B, 45, 5146 (1992).Google Scholar
8. Gilman, J. J., J. Appl. Phys., 27, 1262 (1956).Google Scholar
9. Low, J. R., Symposium on the Relation of Properties to Microstructure, p.153, Amer. Soc. Metals, Cleveland, Ohio (1953).Google Scholar
10. Greenwood, G. W. and Quarrell, A. G., J. Inst. Met., 21, 551 (1954).Google Scholar
11. McMahon, C. J. and Cohen, M., Acta Met., 13, 591 (1965).Google Scholar
12. Petch, N. J., J. Iron Steel Inst. London, 174, 25 (1953).Google Scholar
13. Gilman, J. J., Proc. First Int. Conf. Fracture - Vol.2, Sendai, Japan, p.733 (1966).Google Scholar
14. Hsia, K. J. and Argon, A. S., Materials Science and Engineering A, 176, 111 (1994).Google Scholar