Six precursors were evaluated for use as in situ electron beam-induced deposition capping layers in the preparation of atom probe tomography specimens with a focus on near-surface features where some of the deposition is retained at the specimen apex. Specimens were prepared by deposition of each precursor onto silicon posts and shaped into sub-70-nm radii needles using a focused ion beam. The utility of the depositions was assessed using several criteria including composition and uniformity, evaporation behavior and evaporation fields, and depth of Ga+ ion penetration. Atom probe analyses through depositions of methyl cyclopentadienyl platinum trimethyl, palladium hexafluoroacetylacetonate, and dimethyl-gold-acetylacetonate [Me2Au(acac)] were all found to result in tip fracture at voltages exceeding 3 kV. Examination of the deposition using Me2Au(acac) plus flowing O2 was inconclusive due to evaporation of surface silicon from below the deposition under all analysis conditions. Dicobalt octacarbonyl [Co2(CO)8] and diiron nonacarbonyl [Fe2(CO)9] depositions were found to be effective as in situ capping materials for the silicon specimens. Their very different evaporation fields [36 V/nm for Co2(CO)8 and 21 V/nm for Fe2(CO)9] provide options for achieving reasonably close matching of the evaporation field between the capping material and many materials of interest.

Confocal microscopy was used to image stages of equine zygote development, at timed intervals, after intracytoplasmic sperm injection (ICSI) of oocytes that were matured in vivo or in vitro. After fixation for 4, 6, 8, 12, or 16 h after ICSI, zygotes were incubated with α/β tubulin antibodies and human anticentromere antibody (CREST/ACA), washed, incubated in secondary antibodies, conjugated to either Alexa 488 or Alexa 647, and incubated with 561-Phalloidin and Hoechst 33258. An Olympus IX81 spinning disk confocal microscope was used for imaging. Data were analyzed using χ2 and Fisher’s exact tests. Minor differences in developmental phases were observed for oocytes matured in vivo or in vitro. Oocytes formed pronuclei earlier when matured in vivo (67% at 6 h and 80% at 8 h) than in vitro (13% at 6 and 8 h); 80% of oocytes matured in vitro formed pronuclei by 12 h. More (p=0.04) zygotes had atypical phenotypes, indicative of a failure of normal zygote development, when oocyte maturation occurred in vitro versus in vivo (30 and 11%, respectively). Some potential zygotes from oocytes matured in vivo had normal phenotypes, although development appeared to be delayed or arrested. Confocal microscopy provided a feasible method to assess equine zygote development using limited samples.

Combined oral contraceptive (COC) use is a risk factor for venous thrombosis (VT) and related to the specific type of progestin used. VT is accompanied by inflammation and pathophysiological clot formation, that includes aberrant erythrocytes and fibrin(ogen) interactions. In this paper, we aim to determine the influence of progesterone and different synthetic progestins found in COCs on the viscoelasticity of whole blood clots, as well as erythrocyte morphology and membrane ultrastructure, in an in vitro laboratory study. Thromboelastography (TEG), light microscopy, and scanning electron microscopy were our chosen methods. Our results point out that progestins influence the rate of whole blood clot formation. Alterations to erythrocyte morphology and membrane ultrastructure suggest the presence of eryptosis. We also note increased rouleaux formation, erythrocyte aggregation, and spontaneous fibrin formation in whole blood which may explain the increased risk of VT associated with COC use. Although not all COC users will experience a thrombotic event, individuals with a thrombotic predisposition, due to inflammatory or hematological illness, should be closely monitored to prevent pathological thrombosis.

We present the first demonstration of a general method for the chemical characterization of small surface features at high magnification via simultaneous collection of mass spectrometry (MS) imaging and tandem MS imaging data. High lateral resolution tandem secondary ion MS imaging is employed to determine the composition of surface features on poly(ethylene terephthalate) (PET) that precipitate during heat treatment. The surface features, probed at a lateral resolving power of<200 nm using a surface-sensitive ion beam, are found to be comprised of ethylene terephthalate trimer at a greater abundance than is observed in the surrounding polymer matrix. This is the first chemical identification of PET surface precipitates made without either an extraction step or the use of a reference material. The new capability employed for this study achieves the highest practical lateral resolution ever reported for tandem MS imaging.

Two challenges exist in laser-assisted atom probe tomography (APT). First, a drastic decline in mass-resolving power is caused, not only by laser-induced thermal effects on the APT tips of bulk oxide materials, but also the associated asymmetric evaporation behavior; second, the field evaporation mechanisms of bulk oxide tips under laser illumination are still unclear due to the complex relations between laser pulse and oxide materials. In this study, both phenomena were investigated by depositing Ni- and Co-capping layers onto the bulk LaAlO3 tips, and using stepwise APT analysis with transmission electron microscopy (TEM) observation of the tip shapes. By employing the metallic capping, the heating at the surface of the oxide tips during APT analysis became more symmetrical, thereby enabling a high mass-resolving power in the mass spectrum. In addition, the stepwise microscopy technique visualized tip shape evolution during APT analysis, thereby accounting for evaporation sequences at the tip surface. The combination of “capping” and “stepwise APT with TEM,” is applicable to any nonconductors; it provides a direct observation of tip shape evolution, allows determination of the field evaporation strength of oxides, and facilitates understanding of the effects of ultrafast laser illumination on an oxide tip.

Over the past few decades, remarkable progress has been achieved in terms of understanding the molecular and cellular mechanisms of atherosclerotic vascular calcification and the important role of matrix vesicles in initiating and propagating pathologic tissue mineralization has been widely recognized. Despite these recent advances, however, no definitive data are currently available regarding the texture and composition of the minerals that grow in the vessel wall during the course of the disease. Using different electron microscopy imaging and analysis, we demonstrate that vascular cells can produce and secrete more than one type of matrix vesicles which act as sites for initial mineral deposition independently of their structural features. Our results reveal that apatite formation in the atherosclerotic lesions of the human aorta occur through the deposition of amorphous calcium phosphate that matures over time, transforms into crystalline hydroxyapatite, and radiates towards the lumen of the vesicles, finally forming the calcified spherules. Elemental and mineralogical analyses also demonstrate that the presence of mature and stable amorphous calcium phosphate deposits in the affected tissues is linked to the incorporation of magnesium, which probably delay the conversion to the crystalline phase. Though more rarely, the presence of calcium oxalate crystals has been also documented.

The great potential of scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX) is in detection of unusual chemical elements included in ancient human dental calculus to verify hypotheses about life and burial habits of historic populations and individuals. Elemental spectra were performed from archeological samples of three chosen individuals from different time periods. The unusual presence of magnesium, aluminum, and silicon in the first sample could confirm the hypothesis of high degree of dental abrasion caused by particles from grinding stones in flour. In the second sample, presence of copper could confirm that bronze jewelery could lie near the buried body. The elemental composition of the third sample with the presence of lead and copper confirms the origin of individual to Napoleonic Wars because the damage to his teeth could be explained by the systematic utilization of the teeth for the opening of paper cartridges (a charge with a dose of gunpowder and a bullet), which were used during the 18th and the 19th century AD. All these results contribute to the reconstruction of life (first and third individual) and burial (second individual) habits of historic populations and individuals.

The potential of electrospray deposition, for the controlled preparation of particles for imaging in electron microscopes, is evaluated on various materials: from mono-modal suspensions of spherical particles to multimodal suspensions and to real-world industrial materials. It is shown that agglomeration is reduced substantially on the sample carrier, compared with conventional sample preparation techniques. For the first time, it is possible to assess the number concentration of a tri-modal polystyrene suspension by electron microscopy, due to the high deposition efficiency of the electrospray. We discovered that some suspension stabilizing surfactants form artifact particles during electrospraying. These can be avoided by optimizing the sprayed suspension.

Secondary fluorescence, the final term in the familiar matrix correction triumvirate Z·A·F, is the most challenging for Monte Carlo models to simulate. In fact, only two implementations of Monte Carlo models commonly used to simulate electron probe X-ray spectra can calculate secondary fluorescence—PENEPMA and NIST DTSA-IIa (DTSA-II is discussed herein). These two models share many physical models but there are some important differences in the way each implements X-ray emission including secondary fluorescence. PENEPMA is based on PENELOPE, a general purpose software package for simulation of both relativistic and subrelativistic electron/positron interactions with matter. On the other hand, NIST DTSA-II was designed exclusively for simulation of X-ray spectra generated by subrelativistic electrons. NIST DTSA-II uses variance reduction techniques unsuited to general purpose code. These optimizations help NIST DTSA-II to be orders of magnitude more computationally efficient while retaining detector position sensitivity. Simulations execute in minutes rather than hours and can model differences that result from detector position. Both PENEPMA and NIST DTSA-II are capable of handling complex sample geometries and we will demonstrate that both are of similar accuracy when modeling experimental secondary fluorescence data from the literature.

Coenzyme Q10 (Q10) plays an important role in the cellular antioxidant system by protecting the cells from free-radical oxidative damage and apoptosis. In the present study, we have investigated the effect of Q10 on the preimplantation development of porcine parthenogenetic embryos, as well as the underlying mechanism. The results showed that 100 μM was the optimal concentration of Q10, which resulted in significantly increased cleavage and blastocyst formation rates and improvement of blastocyst quality. Q10 improved the blastocyst hatching rate and cellular proliferation rate in hatching blastocysts and increased the expression of hatching-related genes. Furthermore, Q10 not only decreased reactive oxygen species production, DNA damage levels, and apoptosis in the blastocysts from H2O2-induced oxidative injury, but also maintained mitochondrial function. Taken together, these results indicate that Q10 has beneficial effects on the development of porcine parthenogenetic embryos by preventing oxidative damage and apoptosis.

Formation of a nanometer-scale oxide surface layer is common when a material is exposed to oxygen-containing environment. Employing aberration-corrected analytical transmission electron microscopy and using single crystal SnSe as an example, we show that for an alloy, a second thin amorphous layer can appear underneath the outmost oxide layer. This inner amorphous layer is not oxide based, but instead originates from solid-state amorphization of the base alloy when its free energy rises to above that of the metastable amorphous state; which is a result of the composition shift due to the preferential depletion of the oxidizing species, in our case, the outgoing Sn reacting with the oxygen atmosphere.

In 1994, a new type of atom probe instrument, named the scanning atom probe (SAP), was proposed. The unique feature of the SAP is the introduction of a small extraction electrode, which scans over a specimen surface and confines the high field, required for field evaporation of surface atoms in a small space, between the specimen and the electrode. Thus, the SAP does not require a sharp specimen tip. This indicates that the SAP can mass analyze the specimens which are difficult to form in a sharp tip, such as organic materials and biomolecules. Clean single wall carbon nanotubes (CNT), made by high-pressure carbon monoxide process are found to be the best substrates for biomolecules. Various amino acids and dipeptide biomolecules were successfully mass analyzed, revealing characteristic clusters formed by strongly bound atoms in the specimens. The mass analysis indicates that SAP analysis of biomolecules is not only qualitative, but also quantitative.

Fibrillar collagen in tendons and its natural development in rabbits are discussed in this paper. Achilles tendons from newborn (~7 days) to elderly (~38 months) rabbits were monitored in intact (ntendons=24) and microtome sectioned (ntendons=11) states with label-free second harmonic generation microscopy. After sectioning, the collagen fiber pattern was irregular for the younger animals and remained oriented parallel to the load axis of the tendon for the older animals. In contrast, the collagen fiber pattern in the intact samples followed the load axis for all the age groups. However, there was a significant difference in the tendon crimp pattern appearance between the age groups. The crimp amplitude (A) and wavelength (Λ) started at very low values (A=2.0±0.6 µm, Λ=19±4 µm) for the newborn animals. Both parameters increased for the sexually mature animals (>5 months old). When the animals were fully mature the amplitude decreased but the wavelength kept increasing. The results revealed that the microtome sectioning artifacts depend on the age of animals and that the collagen crimp pattern reflects the physical growth and development.

Vascular stenosis, the abnormal narrowing of blood vessels, arises from defective developmental processes or atherosclerosis-related adult pathologies. Stenosis triggers a series of adaptive cellular responses that induces adverse remodeling, which can progress to partial or complete vessel occlusion with numerous fatal outcomes. Despite its severity, the cellular interactions and biophysical cues that regulate this pathological progression are poorly understood. Here, we report the design and fabrication of a three-dimensional (3D) in vitro system to model vascular stenosis so that specific cellular interactions and responses to hemodynamic stimuli can be investigated. Tubular cellularized constructs (cytotubes) were produced, using a collagen casting system, to generate a stenotic arterial model. Fabrication methods were developed to create cytotubes containing co-cultured vascular cells, where cell viability, distribution, morphology, and contraction were examined. Fibroblasts, bone marrow primary cells, smooth muscle cells (SMCs), and endothelial cells (ECs) remained viable during culture and developed location- and time-dependent morphologies. We found cytotube contraction to depend on cellular composition, where SMC-EC co-cultures adopted intermediate contractile phenotypes between SMC- and EC-only cytotubes. Our fabrication approach and the resulting artery model can serve as an in vitro 3D culture system to investigate vascular pathogenesis and promote the tissue engineering field.

The Monte Carlo program PENEPMA performs simulations of X-ray emission from samples bombarded with both electron and photon beams. It is based on the general-purpose Monte Carlo simulation package PENELOPE, an elaborate system for the simulation of coupled electron-photon transport in arbitrary materials, and on the geometry subroutine package PENGEOM, which tracks particles through complex material structures defined by quadric surfaces. After a brief description of the interaction models implemented in the simulation subroutines and of the structure and operation of PENEPMA, we provide an overview of the capabilities of the program along with several examples of its application to the modeling of electron probe microanalysis measurements.