Hostname: page-component-7bb8b95d7b-495rp Total loading time: 0 Render date: 2024-09-18T12:15:50.854Z Has data issue: false hasContentIssue false

Calibration of the Raman effect in α–Al2O3 ceramic for residual stress measurements

Published online by Cambridge University Press:  03 March 2011

M.R. Gallas*
Affiliation:
Materials Science and Engineering Laboratory, National Institute of Standards and Technology, Gaithersburg, Maryland 20899
Y.C. Chu*
Affiliation:
Materials Science and Engineering Laboratory, National Institute of Standards and Technology, Gaithersburg, Maryland 20899
G.J. Piermarini
Affiliation:
Materials Science and Engineering Laboratory, National Institute of Standards and Technology, Gaithersburg, Maryland 20899
*
a)Permanent address: Instiuto de Fisica, Universidade Federal do Rio Grande do Sul, Porto Alegre, Brasil.
b)Permanent address: Department of Chemistry, Howard University, Washington, DC.
Get access

Abstract

The pressure shifts of the 418 and 379 cm−1 Raman lines of polycrystalline α-Al2O3 ceramic were measured at room temperature to 3190 MPa. A diamond anvil high pressure cell was used in conjunction with a microRaman spectrometer system. Pressures were measured by the ruby fluorescence method. Distilled water was used as the pressure transmitting medium. The pressure dependence of the wave number for the hydrostatic range (to 1585 MPa) was found to be 0.00220 ± 0.00007 cm−1 MPa−1 for the 418 cm−1 Raman line and 0.0011 ± 0.0001 cm−1 MPa−1 for the 379 cm−1 line. Both shifts are based on a linear least squares fit to the data within a 95% confidence interval. Measurements that included the nonhydrostatic regime (to 3190 MPa) gave similar shifts, but with almost twice the uncertainty. Absolute residual stresses in alumina ceramics are in the 200 to 600 MPa range with higher values, 1790 MPa, reported for single-crystal alumina. For the 418 cm−1 Raman line, these values correspond to shifts of 0.4, 1.4, and 3.9 cm−1, respectively. The sensitivity of the microRaman technique is sufficient to detect and measure residual stresses of this magnitude.

Type
Articles
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Forman, R. A., Piermarini, G.J., Barnett, J. D., and Block, S., Science 176, 284 (1972).CrossRefGoogle Scholar
2DiGregorio, J. F., Furtak, T. E., and Petrovic, J. J., J. Appl. Phys. 71, 3524 (1991).CrossRefGoogle Scholar
3Haerle, A. G., Cannon, W. R., and Denda, M., J. Am. Ceram. Soc. 74, 2897 (1991).CrossRefGoogle Scholar
4Grabner, L., J. Appl. Phys. 49, 580 (1978).CrossRefGoogle Scholar
5Rydzak, J.W. and Cannon, W.R., J. Am. Ceram. Soc. 72, 1559 (1989).CrossRefGoogle Scholar
6Molis, S.E. and Clarke, D., J. Am. Ceram. Soc. 73, 3189 (1990).CrossRefGoogle Scholar
7Cheong, Y. M., Marcus, H. L., and Adar, F., J. Mater. Res. 2, 902 (1987).CrossRefGoogle Scholar
8Salje, V.E., J. Appl. Crystallogr. 6, 442 (1973).CrossRefGoogle Scholar
9Ma, Q. and Clarke, D.R., J. Am. Ceram. Soc. 76, 1433 (1993).CrossRefGoogle Scholar
10Ma, Q. and Clarke, D.R., Acta. Metall. Mater. 41, 1811 (1993).CrossRefGoogle Scholar
11Ma, Q. and Clarke, D.R., Acta. Metall. Mater. 41, 1817 (1993).CrossRefGoogle Scholar
12Yang, X., Hu, X., Day, R.J., and Young, R.J., J. Mater. Sci. 27, 1409 (1992).CrossRefGoogle Scholar
13Porto, S.P.S. and Krishnan, R.S., J. Chem. Phys. 47, 1009 (1967).CrossRefGoogle Scholar
14Munro, R.G., Block, S., Piermarini, G.J., and Mauer, F. A., in Materials Science Research, Vol. 17, Emergent Process Methods for High Technology Ceramics, edited by Davis, R.F., Palmour, H. III, and Porter, R.L. (Plenum Press, New York, 1984), pp. 783792.CrossRefGoogle Scholar
15Mortensen, A., Christensen, D.H., Faurskov Nielsen, O., and Pedersen, E., J. Raman Spectros. 24, 667 (1993).CrossRefGoogle Scholar
16Piermarini, G.J., Munro, R.G., and Block, S., in High Pressure in Science and Technology, edited by Homan, C., MacCrone, R. K., and Whalley, E. (Mater. Res. Soc. Symp. Proc. 22, Elsevier Science Publishing, New York, NY, 1984), pp. 2528.Google Scholar
17Cook, R.F., Liniger, E.G., Steinbrech, R.W., and Deuerler, F., J. Am. Ceram. Soc. 77, 303 (1994).CrossRefGoogle Scholar