In this paper, the results of a series of experiments funded by DARPA to determine the feasibility of using small actuators to provide directional control for a supersonic projectile are presented. Controlling the flight of the projectile was accomplished by taking advantage of complex shock-boundary-layer interactions produced by mechanical devices. Experimental tests were conducted at GTRI to screen several control concepts and actuator locations. Further experiments were conducted on a scale projectile in a supersonic stream to investigate the rise time of the forces. Several different mechanical actuators were tested which served to provide guidance for future actuator designs. CFD results were also used to predict the results in flight as well as gain insights into the fluid mechanics involved. Flight tests of a Mach 4 round proved the viability of the guidance actuator.

Particle image velocimetry (PIV) measurements of the flow around a wing section are employed as a basis for non-intrusive aerodynamic mean loads characterisation, providing sectional lift, drag and pitching moment. The technique relies upon the application of control-volume approaches in combination with the deduction of the pressure from the PIV experimental data through application of the momentum equation. The treatment can also be applied when the flow is unsteady; in that case time-mean loads are obtained from velocity statistics, through the use of Reynolds-averaged formulation of the governing equations. The procedure was applied in the experimental investigation of a NACA 642A015 aerofoil, in which the PIV approach is validated against standard pressure-based methods (surface pressure distribution and wake rake). The chord Reynolds number considered in the investigation ranges between 1 – 7 × 105. In addition, the consistency and potential performance of the method was assessed by means of synthetic velocity field data obtained from a numerical flow simulation.

Successful, seamless interchange of simulation databases has long proved surprisingly difficult to achieve. Numerous technical difficulties, arising from the different environmental representations used by different simulation systems, have proved to be only one facet of this difficulty. Often such problems are in fact the result of more fundamental underlying issues, such as the mathematical relationships between different co-ordinate systems. Logistical issues, and collaborative aspects of database interchange between different groups or companies, also contribute to the problems.

Thales has encountered many of these issues over the years in generating a range of databases for its simulation systems. These databases are required to correlate closely with other sensor systems, in particular the visual, but it is often the case that these other systems are third party products, using databases modelled by companies other than Thales. In these circumstances, the strategy used by Thales to generate its databases has typically been to derive them directly from the visual database. This has involved directly processing the visual database, extracting relevant geometry and attribution and formatting it for use by the Thales simulation systems. Historically, such visual databases have been provided by third parties using the SIF/HDI interchange format and imported directly into the Thales database generation toolset. While generating such derived databases in this way has been achieved successfully, many interchange issues referred to above were encountered and needed to be addressed.

When the need arose to replace SIF/HDI, the opportunity was taken to seek a replacement that would not only provide better representational capabilities but also address many of the wider, non-technical issues as well. Analysis of a variety of formats was undertaken and SEDRIS emerged as by far the strongest contender. Not only did it provide the best all round support for existing data representation requirements, it also gave good support for addressing wider interchange issues and offered a variety of opportunities to enhance the database generation toolset, both during initial development and over time.

This paper will discuss experiences using SEDRIS in this context. It will examine the basic representational requirements that needed to be met and the interchange problems that were to be overcome. The ways in which SEDRIS was seen to address these problems will be considered, along with the other advantages SEDRIS offered. Experiences developing SEDRIS software and interchanging databases using SEDRIS will also be described, including some lessons learned concerning both the use of SEDRIS and database interchange in general.

A new controller design method of lateral-directional dynamics is proposed. This method is based on the formulated pilot model, and the controller is designed so that the pilot-aeroplane system attains the desired requirements. Robust stabilities and handling qualities can be taken into account. The proposed method was applied to B747 dynamics, and flight simulator experiments were performed, and the designed controller was verified.

The first supersonic business jet to enter the market will not face its competition from rival supersonic designs under development. Its true competitors are the then current generation of highly evolved high-subsonic business jets when compared on economic grounds. For a price tag of $1m for the new conception of very light jets, ranging up to $45m for the highest-performing ‘race-horse’-like corporate jets, this breed of aircraft is able to accommodate the needs of most executives, VIPs, officials, from corporate transportation to cargo services of civil to military origin. Understanding the state of modern business class aircraft and their market is essential in gaining base knowledge required for any supersonic business jet endeavor aiming at a prospective market. The key descriptors for this marketplace are market potential, market productivity, and market drivers, altogether being a measure for growth and consumer demand. Such common denominator is used to gain the understanding necessary to ascertain and visualise the top level implications regarding any supersonic business case. Having assembled an understanding of the key descriptors for business aviation, the study first analyses the flight operation of traditional subsonic and high-subsonic business jets. Such perceptive is then complemented with the peculiarities associated with supersonic operation, ultimately defining the supersonic solution space consisting of market viability, efficiency, and overall flight performance. Consequently, a vehicle development strategy and mission specification are suggested for the first generation of supersonic business jets (SSBJ) and supersonic cargo jets (SSCJ).