To save content items to your account,
please confirm that you agree to abide by our usage policies.
If this is the first time you use this feature, you will be asked to authorise Cambridge Core to connect with your account.
Find out more about saving content to .
To save content items to your Kindle, first ensure email@example.com
is added to your Approved Personal Document E-mail List under your Personal Document Settings
on the Manage Your Content and Devices page of your Amazon account. Then enter the ‘name’ part
of your Kindle email address below.
Find out more about saving to your Kindle.
Note you can select to save to either the @free.kindle.com or @kindle.com variations.
‘@free.kindle.com’ emails are free but can only be saved to your device when it is connected to wi-fi.
‘@kindle.com’ emails can be delivered even when you are not connected to wi-fi, but note that service fees apply.
Experimental results obtained with “Kanal-2” facility under the study of powerful laser pulse interaction with the low density microstructure media are presented and discussed in this paper. Forward scattering, back scattering, and transmission of laser radiation by aerogel foil plasma have been investigated. The temporal, spectral, and energy characteristics of both the radiation scattering in the direction of heating radiation beam and the back scattering radiation were studied; the directional diagrams of forward and back scattering radiation were obtained for ω0 and 2ω0 frequencies. Analysis of intensity redistribution on the heating beam cross-section after passing through a polymer microstructure target was carried out.
New results obtained in experiments on laser irradiation (I = 5 × 1013 W/cm2, λ = 1.054 µm) of low-density (2–10 mg/cm3) porous materials (agar, triacetate cellulose, and foam polysterene) are presented and discussed from the standpoint of optimum porous material utilization in target designs for inertial confinement fusion. The influence of low-density material microstructure of irradiated samples on the absorption of laser radiation and the energy transfer processes was investigated using X-ray and optical diagnostic methods with high temporal and spatial resolution.
The experience of target fabrication with low-density and cluster
heterogeneity is presented. Cluster plasma research is strongly dependent
on target fabrication development and target structure characterization.
Ten more target parameters should be measured for experiment interpreting
in case of micro-heterogeneous plasma. Foam and foil targets, high-Z doped
also, are produced and irradiated on the existing laser facilities. The
density of 4.5 mg/cc cellulose triacetate in the form of regular
three-dimensional polymer networks are achieved which is as low as plasma
critical density for the third harmonic of iodine laser light. The
possibilities of varying important target parameters, methods of their
monitoring are discussed. Experiments with underdense foam targets with or
without clusters irradiated on Prague Asterix Laser System (PALS) laser
facility are analyzed preliminary for target optimization. Under-critical
foams of varying structure (closed-cell foam or three-dimensional
networks) and densities are reported for plasma experiments. Thermal and
radiation transport in such targets are considered.
Popular target designs are reviewed. Possible methods of fusion
target fabrication are discussed and the equipment and samples are
demonstrated. The properties of the uniform and structured (cluster)
materials are considered, showing the advantage of cluster material for
energy conversion into soft X rays. The target materials with high
content of hydrogen isotopes (BeD2, LiBeD3, or
ND3BD3) prove to be more effective for high-power
drivers in comparison with beryllium or polyimide.
Two shells with the diameter of 0.8–0.9 mm
and a wall thickness of ≅1 μm were produced at
the Lebedev Physics Institute for the experiments conducted
at the ISKRA-5 facility. The results of two experiments
with the aforementioned shells conducted at the ISKRA-5
facility with the use of an indirect-drive set up. In one
of the experiments, the diameter of the golden hohlraum
was D = 2 mm while in the other it was D =
4 mm. In these experiments it was observed to be ≅4
times the difference of the average laser intensity on the
hohlraum surface. The results of computational analysis of the
experiments are also presented here.
Email your librarian or administrator to recommend adding this to your organisation's collection.