In view of the cooperative guidance problem with time delay, this paper proposes a two-stage time-delay prescribed-time cooperative guidance law in the three-dimensional (3D) space. In the first stage, by introducing a time scaling function and time-delay consensus, the proposed cooperative guidance law can overcome the negative influence of time delay to guaranteed the desired convergence performance. Derived from the Lyapunov convergence analysis, the time-delay stability of the first stage can be ensured and the convergence time can be described as the relationship between delayed time and mission-assigned convergence time. Then, taking the prescribed-time-related convergence time as the switching point, the second stage begins with suitable initial conditions and all interceptors are governed by proportional navigation guidance. Finally, comparative simulations are performed to demonstrate the effectiveness and superiority of the proposed time-delay guidance law.

We report the experimental results of the commissioning phase in the 10 PW laser beamline of the Shanghai Superintense Ultrafast Laser Facility (SULF). The peak power reaches 2.4 PW on target without the last amplifying during the experiment. The laser energy of 72 ± 9 J is directed to a focal spot of approximately 6 μm diameter (full width at half maximum) in 30 fs pulse duration, yielding a focused peak intensity around 2.0 × 1021 W/cm2. The first laser-proton acceleration experiment is performed using plain copper and plastic targets. High-energy proton beams with maximum cut-off energy up to 62.5 MeV are achieved using copper foils at the optimum target thickness of 4 μm via target normal sheath acceleration. For plastic targets of tens of nanometers thick, the proton cut-off energy is approximately 20 MeV, showing ring-like or filamented density distributions. These experimental results reflect the capabilities of the SULF-10 PW beamline, for example, both ultrahigh intensity and relatively good beam contrast. Further optimization for these key parameters is underway, where peak laser intensities of 1022–1023 W/cm2 are anticipated to support various experiments on extreme field physics.

For the safety problems caused by the limited landing space of the deck during the arresting process of the carrier-based aircraft, a dynamic model of the carrier-based aircraft’s landing and arresting is built. Based on the batch simulation method, the lateral dynamics safety envelope of the aircraft during the arresting was defined, and the dynamic response of the key points in the envelope during the arresting process was investigated. Subsequently, the influence of engine thrust and aircraft quality on the arresting safety envelope was studied based on reasonable safety evaluation indicators, and the safety status envelope of the deck arresting was given. Then, the particular Hamilton-Jacobi partial differential equation is used to obtain the lateral dynamics safety envelope of the carrier-based aircraft in the process of landing and arresting by backward inversion. Results indicate that engine thrust and landing quality have little effect on the yaw angle in the arresting safety boundary during the arresting. Additionally, with the engine thrust and landing quality increase, the maximum safe off-centre distance gradually decreases, and the safety boundary decreases accordingly. During the phase of landing glide, the engine thrust and quality have little effect on the maximum safe eccentric distance. When the engine thrust is increased by 40%, the maximum safe yaw angle is reduced from 0.3°, and the safety boundary is reduced by 4.2%. When the aircraftquality increases by 40%, the maximum safe yaw angle is reduced by 0.4°, and the safety boundary is reduced by 2.8%. The findings of this paper can provide framework for the research on theaircraft-to-carrier dynamic matching characteristics of the carrier-based system, and is of great significance to the research on improving the safety of the carrier-based aircraft landing arresting.

We report on experimental observation of non-laminar proton acceleration modulated by a strong magnetic field in laser irradiating micrometer aluminum targets. The results illustrate the coexistence of ring-like and filamentation structures. We implement the knife edge method into the radiochromic film detector to map the accelerated beams, measuring a source size of 30–110 μm for protons of more than 5 MeV. The diagnosis reveals that the ring-like profile originates from low-energy protons far off the axis whereas the filamentation is from the near-axis high-energy protons, exhibiting non-laminar features. Particle-in-cell simulations reproduced the experimental results, showing that the short-term magnetic turbulence via Weibel instability and the long-term quasi-static annular magnetic field by the streaming electric current account for the measured beam profile. Our work provides direct mapping of laser-driven proton sources in the space-energy domain and reveals the non-laminar beam evolution at featured time scales.

The aim of this study was to develop and externally validate a simple-to-use nomogram for predicting the survival of hospitalised human immunodeficiency virus/acquired immunodeficiency syndrome (HIV/AIDS) patients (hospitalised person living with HIV/AIDS (PLWHAs)). Hospitalised PLWHAs (n = 3724) between January 2012 and December 2014 were enrolled in the training cohort. HIV-infected inpatients (n = 1987) admitted in 2015 were included as the external-validation cohort. The least absolute shrinkage and selection operator method was used to perform data dimension reduction and select the optimal predictors. The nomogram incorporated 11 independent predictors, including occupation, antiretroviral therapy, pneumonia, tuberculosis, Talaromyces marneffei, hypertension, septicemia, anaemia, respiratory failure, hypoproteinemia and electrolyte disturbances. The Likelihood χ2 statistic of the model was 516.30 (P = 0.000). Integrated Brier Score was 0.076 and Brier scores of the nomogram at the 10-day and 20-day time points were 0.046 and 0.071, respectively. The area under the curves for receiver operating characteristic were 0.819 and 0.828, and precision-recall curves were 0.242 and 0.378 at two time points. Calibration plots and decision curve analysis in the two sets showed good performance and a high net benefit of nomogram. In conclusion, the nomogram developed in the current study has relatively high calibration and is clinically useful. It provides a convenient and useful tool for timely clinical decision-making and the risk management of hospitalised PLWHAs.

Cadmium (Cd) is a toxic heavy metal that poses a threat to the health of humans and animals. It can cause serious damage to the small intestine, which is the main absorption site of Cd and the primary target organ after oral administration. Our previous study found that zinc chelate of hydroxy analogue of methionine (Zn-HMTB), a new type of feed additive, decreased Cd accumulation in the liver and kidneys. The aim of this study was to investigate the effect of Zn-HMTB on Cd absorption and Cd-induced toxicity in the small intestine of piglets. Twenty-four piglets (Landrace × Large White, 13.22 ± 0.58 kg BW) were randomly divided into four dietary treatment groups: basal diet, and diets containing 30 mg/kg Cd from CdCl2 and 0, 100 or 200 mg/kg Zn from Zn-HMTB. The experiment lasted 27 days. The feed intake and final BW of each piglet were recorded at the end of the experiment. Gastrointestinal (GI) tract tissue and samples of liver, kidney, spleen, heart, lung and longissimus muscle tissue and faeces were collected. The concentrations of Cd and metal trace elements in the GI tract and organs were analysed, as was the relative messenger RNA (mRNA) expression of inflammatory cytokines and metal element transporters in the small intestine, and epithelial apoptosis in the small intestine. The results showed that, compared with Cd-treated piglets, piglets in the Zn-HMTB and Cd cotreatment groups had less Cd deposition in the stomach, ileum, caecum, colon, liver, kidneys, spleen, lungs, heart and muscles (P < 0.05), and lower Cd concentrations in faeces (P < 0.05), suggesting that Zn-HMTB increased Cd absorption and the excretion of Cd in other forms (possibly urine). Zinc chelate of hydroxy analogue of methionine increased Zn deposition in the jejunum and the relative mRNA expression of divalent metal transporters 1 and zinc transporter 5 in the duodenum (P < 0.05), indicating that Zn-HMTB may promote the absorption and transportation of Cd and Zn together by upregulating metal element transporters. Competition between Zn and Cd may be responsible for accelerating Cd excretion. Furthermore, Zn-HMTB reduced Cd-induced apoptosis of enterocytes and inflammatory stimuli in the small intestine, suggesting that Zn-HMTB reduced Cd-induced toxicity to the small intestine. These results suggest that Zn-HMTB can be helpful in decreasing Cd accumulation in the GI tract and organs of piglets and relieving Cd-induced toxicity to the small intestine but cannot reduce the absorption of Cd.

Glyphodes pyloalis Walker (Lepidoptera: Pyralididae) is a common pest in sericulture and has developed resistance to different insecticides. However, the mechanisms involved in insecticide resistance of G. pyloalis are poorly understood. Here, we present the first whole-transcriptome analysis of differential expression genes in insecticide-resistant and susceptible G. pyloalis. Clustering and enrichment analysis of DEGs revealed several biological pathways and enriched Gene Ontology terms were related to detoxification or insecticide resistance. Genes involved in insecticide metabolic processes, including cytochrome P450, glutathione S-transferases and carboxylesterase, were identified in the larval midgut of G. pyloalis. Among them, CYP324A19, CYP304F17, CYP6AW1, CYP6AB10, GSTs5, and AChE-like were significantly increased after propoxur treatment, while CYP324A19, CCE001c, and AChE-like were significantly induced by phoxim, suggesting that these genes were involved in insecticide metabolism. Furthermore, the sequence variation analysis identified 21 single nucleotide polymorphisms within CYP9A20, CYP6AB47, and CYP6AW1. Our findings reveal many candidate genes related to insecticide resistance of G. pyloalis. These results provide novel insights into insecticide resistance and facilitate the development of insecticides with greater specificity to G. pyloalis.

An experiment was conducted to determine the effects of supplementing different amounts of daidzein in a diet on the growth performance, blood biochemical parameters and meat quality of finishing beef cattle. Thirty finishing Xianan steers were distributed in three groups equilibrated by weight and fed three different dietary treatments (concentrate ratio = 80%): (1) control; (2) 500 mg/kg daidzein and (3) 1000 mg/kg daidzein, respectively. Steers were slaughtered after an 80-day feeding trial. Results showed that daidzein supplementation had no effect on the final body weight, average daily gain and feed conversion rate of steers. Steers fed with 1000 mg/kg daidzein had greater dry matter intake than those fed with control diets. Compared with the control group, the 1000 mg/kg daidzein group had a higher fat thickness, lower shear force and lightness. The pH, drip loss, cooking loss, redness (a*), yellowness (b*), moisture, ash, crude protein and intramuscular fat of the Longissimus dorsi muscle were unaffected by daidzein supplementation. Compared with the control group, the 1000 mg/kg daidzein group significantly increased the serum concentrations of insulin, free fatty acid and Glutamic-pyruvic transaminase. The 500 mg/kg daidzein group significantly increased the serum concentration of tetraiodothyronine compared with the control group. Supplemental daidzein did not affect the blood antioxidant ability and blood immune parameters in serum. In conclusion, daidzein supplementation above 500 mg/day modifies feed intake and metabolic and hormonal profile, with positive and negative effects on meat quality.

The prevalence of sexually transmitted infection (STI) pathogens in Beijing, China, is rarely reported. In this study, 34 911 symptomatic outpatients with suspected genital infections who attended outpatient clinics in a tertiary care hospital were included to investigate the updated prevalence of Ureaplasma urealyticum (UU), Chlamydia trachomatis (CT), Neisseria gonorrhoeae (NG) and herpes simplex virus (HSV) from 1 January 2013 to 31 December 2016 in Beijing, China. Results indicated that a decrease trend (UU, CT, NG and HSV) in male and an increase trend (UU, CT and NG) in female were observed during the period. Patients aged 20–39 years old were mostly affected by these pathogens, while the prevalence in patients aged 20–29 years old was the highest, The prevalence of UU in male was significantly lower than in female (31.5% vs. 49.3%, P < 0.05), while the prevalence of NG in male was significantly higher than in female (2.5% vs. 0.8%, P < 0.05). In patients with co-infections, 60.6% of male and 71.4% of female were co-infected by UU + CT. In total, 11.9% and 88.1% of patients with HSV infections were confirmed to be infected by HSV-1 and HSV-2. This study could contribute to a better understanding of the current epidemiological features of UU, NG, CT and HSV among symptomatic patients attending an outpatient clinic in Beijing, China, and thus facilitate to develop more effective intervention, prevention and treatment of STI.

In this paper, we consider the existence of multiple solutions for the quasilinear Schrödinger equation

$$\left\{ {\matrix{ {-\Delta u-\Delta (\vert u \vert ^\alpha )\vert u \vert ^{\alpha -2}u = g(x,u) + \theta h(x,u),\;\;x\in \Omega } \hfill \cr {u = 0,\;\;x\in \partial \Omega ,} \hfill \cr } } \right.$$

In this study, poly(methyl methacrylate-maleic anhydride) (P(MMA-MAh)) was synthesized in toluene from methyl methacrylate (MMA) and maleic anhydride (MAh) monomers via free radical polymerization, in the presence of 2,2′-Azo-bis-isobutyronitrile (AIBN), as initiator at 80ºC for 8 h. The molar ratio of monomers was found to be 1 MAh:8 MMA using hydrolysis and titration. The molecular weight of co-polymer was determined to be of the order of 104 (g/mol) by gel permeation chromatography. The co-polymer was characterized using Fourier transform infrared and nuclear magnetic resonance spectroscopy. Thermogravimetric analysis indicated the initial decomposition temperature was ~270ºC. Differential scanning calorimetry indicated that the glass transition temperature was near 126ºC.

Rectorite modified with benzyldimethyldodecylammonium chloride (OREC) was used as an additive to modify gel polymer electrolytes (GPEs) which consisted of P(MMA-MAh) used as a polymer matrix, propylene carbonate (PC) as a plasticizer and LiClO4 as the lithium ion source. X-ray diffraction analysis indicates that OREC can exfoliate well in GPEs when the amount of clay is suitable. The temperature dependence of the ionic conductivity of the resulting GPEs agreed well with the VTF (Vogel-Tamman-Fulcher) relation. OREC doses of 5 phr resulted in the greatest ionic conductivity. This OREC addition considerably improved the plasticized retention levels. As a consequence of OREC occupying the free volume space in the polymer matrix of GPEs, the bulk resistance of the GPEs was reduced and the glass transition temperature (Tg) increased.

In liquid-filled batteries, the liquid electrolytes may escape or present a fire hazard and an inert spacer is needed to separate the electrodes. Alternative polymer-based electrolytes are of current technological interest. Solid polymer electrolytes are non-volatile, non-corrosive materials, which can readily be processed into any shape or size. However, despite possessing the required mechanical properties, they have inherently lower conductivity. Gel-based systems are an attempt to strike a balance between the high conductivity of organic liquid electrolytes and the dimensional stability of a solid polymer.

Rectorite was modified with dodecyl benzyl dimethyl ammonium chloride to form organic-modified rectorite (OREC). OREC was used as a filler additive to modify gel polymer electrolytes (GPEs) and prepare composite gel polymer electrolytes (CPEs) which consisted of polymethyl methacrylate (PMMA) used as a polymer matrix, propylene carbonate (PC), used as a plasticizer, and LiClO4, used as a lithium ion producer. A variety of physical and chemical techniques was used to characterize the CPEs. The interlayer d spacing of OREC was much larger than that of the initial rectorite (2.22 nm). OREC also possesses a fine microscopic structure, and has a hydrophobic surface. Molau and XRD analysis of CPEs indicate that OREC has good compatibility with the components of CPEs and can be dispersed well. The effects of temperature and OREC dose on properties were studied. The temperature dependence of ionic conductivity of CPEs is well fitted by the VTF (Vogel-Tamman-Fulcher) relation. OREC doses of 5 phr gave the greatest ionic conductivity. This amount also greatly increased the plasticizer maintenance levels. Due to the occupancy of free volume space in the polymer matrix of CPEs by OREC, the bulk resistance of the CPEs was lowered and the glass transition temperature (Tg) increased. The sheet structure of OREC is thought to improve the decomposition temperature of CPEs.

Rectorite (REC) was modified with dodecyl benzyl dimethyl ammonium chloride (1227) to form an organic-modified rectorite, termed OREC. The OREC was used as a filler additive to modify gel polymer electrolytes (GPEs) which consisted of polymethyl methacrylate (PMMA), propylene carbonate (PC) and LiClO4. Studies of ionic conductivity and viscosity of liquid electrolytes and pure PC, respectively, clearly showed that these properties are greatly influenced by temperature and the amount of OREC added; a consequence of the interactions between the components of CPEs. The Fourier transform infrared (FTIR) spectroscopy results indicated that there were two kinds of interaction: namely (1) a strong hydrogen bond between Si–OH and C=O of PC and (2) a weak interaction between Li+ and C=O. Inverse gas chromatography (IGC) research supported the FTIR interpretation, indicating that the two interactions exist and that the H bond is the stronger of the two. In CPEs, the polymer matrix of PMMA merely supports the active components and does not influence the interactions between them. The OREC greatly increased the crucial plasticizer maintenance property when the amount of clay added was optimum.

Surface exfoliation was observed on single-crystal silicon surface under the action of compressed plasma flow (CPF). This phenomenon is mainly attributed to the strong transient thermal stress impact induced by CPF. To gain a better understanding of the mechanism, a micro scale model combined with thermal conduction and linear elastic fracture mechanics was built to analyze the thermal stress distribution after energy deposition. After computation with finite element method, J integral parameter was applied as the criterion for fracture initiation evaluation. It was demonstrated that the formation of surface exfoliation calls for specific material, crack depth, and CPF parameter. The results are potentially valuable for plasma/matter interaction understanding and CPF parameter optimization.

Fermented soybean meal (FSM), which has lower anti-nutritional factors and higher active enzyme, probiotic and oligosaccharide contents than its unfermented form, has been reported to improve the feeding value of soybean meal, and hence, the growth performance of piglets. However, whether FSM can affect the bacterial and metabolites in the large intestine of piglets remains unknown. This study supplemented wet-FSM (WFSM) or dry-FSM (DFSM) (5% dry matter basis) in the diet of piglets and investigated its effects on carbon and nitrogen metabolism in the piglets’ large intestines. A total of 75 41-day-old Duroc×Landrace×Yorkshire piglets with an initial BW of 13.14±0.22 kg were used in a 4-week feeding trial. Our results showed that the average daily gain of piglets in the WFSM and DFSM groups increased by 27.08% and 14.58% and that the feed conversion ratio improved by 18.18% and 7.27%, respectively, compared with the control group. Data from the prediction gene function of Phylogenetic Investigation of Communities by Reconstruction of Unobserved States (PICRUSt) based on 16S ribosomal RNA (rRNA) sequencing showed that carbohydrate metabolism function families in the WFSM and DFSM groups increased by 3.46% and 2.68% and that the amino acid metabolism function families decreased by 1.74% and 0.82%, respectively, compared with the control group. These results were consistent with those of other metabolism studies, which showed that dietary supplementation with WFSM and DFSM increased the level of carbohydrate-related metabolites (e.g. 4-aminobutanoate, 5-aminopentanoate, lactic acid, mannitol, threitol and β-alanine) and decreased the levels of those related to protein catabolism (e.g. 1,3-diaminopropane, creatine, glycine and inosine). In conclusion, supplementation with the two forms of FSM improved growth performance, increased metabolites of carbohydrate and reduced metabolites of protein in the large intestine of piglets, and WFSM exhibited a stronger effect than DFSM.