This paper provides a summary of recent research connected with the shock ignition (SI) concept of the inertial confinement fusion which was carried out at PALS. In the experiments, Cu planar targets coated with a thin CH layer were used. Two-beam irradiation experiment was applied to investigate the effect of preliminary produced plasma to shock-wave generation. The 1ω or 3ω main beam with a high intensity >1015 W/cm2 generates shock wave, while the other 1ω beam with the intensity below 1014 W/cm2 creates CH pre-plasma simulating the pre-compressed plasma related to SI. Influence of laser wavelength on absorbed energy transfer to shock wave was studied by means of femtosecond interferometry and measuring the crater volume. To characterize the hot electron and ion emission, two-dimensional (2D) Kα-imaging of Cu plasma and grid collector measurements were used. In single 1ω beam experiments energy transport by fast electrons produced by resonant absorption made a significant contribution to shock-wave pressure. However, two-beam experiments with 1ω main beam show that the pre-plasma is strongly degrading the scalelength which leads to decreasing the fast electron energy contribution to shock pressure. In both the single 3ω beam experiments and the two-beam experiments with the 3ω main beam, do not show any clear influence of fast electron transport on shock-wave pressure. The non-monotonic behavior of the scalelength at changing the laser beam focal radius in both presence and absence of pre-plasma reflects the competition of plasma motion and electron heat conduction under the conditions of one-dimensional and 2D plasma expansion at large and small focal radii, respectively.

The paper is a continuation of research carried out at Prague Asterix Laser System (PALS) related to the shock ignition (SI) approach in inertial fusion, which was carried out with use of 1ω main laser beam as the main beam generating a shock wave. Two-layer targets were used, consisting of Cu massive planar target coated with a thin polyethylene layer, which, in the case of two-beam irradiation geometry, simulate conditions related to the SI scenario. The investigations presented in this paper are related to the use of 3ω to create ablation pressure for high-power shock wave generation. The interferometric studies of the ablative plasma expansion, complemented by measurements of crater volumes and Kα emission, clearly demonstrate the effect of changing the incident laser intensity due to changing the focal radius on efficiency of laser energy transfer to a shock wave and fast electron emission. The efficiency of the energy transfer increases with the radius of the focused laser beam. The pre-plasma does not significantly change the character of this effect. However, it unambiguously results in the increasing temperature of fast electrons, the total energy of which remains very small (<0.1% of the laser energy). This study shows that the optimal radius from the point of view of 3ω radiation energy transfer to the shock wave is the maximal one used in these experiments and equal to 200 µm that corresponds to the minimal effect of two-dimensional (2D)-expansion. Such a result is typical for the ablation process determined by electron conductivity energy transfer under the conditions of one-dimensional or 2D matter expansion without any appreciable effect due to energy transfer by fast electrons. The 2D simulations based on application of the ALANT-HE code and an analytical model that includes generation and transport of hot electrons has been used to support of experimental data.

In the previous works (Rozanov et al., 2013; 2015) we have performed one-dimensional (1D) numerical simulations of the target compression and burning at the absorbed energy of ~1.5 MJ. As a result, the target was chosen to have a low initial aspect ratio in order to be less sensitive to the influence of such parameters as laser pulse duration, total laser energy, and equations of state model. The simulation results demonstrated a higher probability of ignition and effective burning of such a system. In the present work we discuss the impact of irradiation asymmetry on this baseline target implosion. The details of the 1D compression and a possible influence of 2D and 3D effects due to the hydrodynamic instability and mixing have been described. In accordance with the 2D calculations the target is still ignited, however, the symmetry analysis of 3D ones gives reasons to further reduce the efficiency of conversion of kinetic energy into potential energy.

This paper reports on properties of a plasma formed by sequential action of two laser beams on a flat target, simulating the conditions of shock-ignited inertial confinement fusion target exposure. The experiments were performed using planar targets consisting of a massive copper (Cu) plate coated with a thin plastic (CH) layer, which was irradiated by the 1ω PALS laser beam (λ = 1.315 μm) at the energy of 250 J. The intensity of the fixed-energy laser beam was scaled by varying the focal spot radius. To imitate shock ignition conditions, the lower-intensity auxiliary 1ω beam created CH-pre-plasma which was irradiated by the main beam with a delay of 1.2 ns, thus generating a shock wave in the massive part of the target. To study the parameters of the plasma treated by the two-beam irradiation of the targets, a set of various diagnostics was applied, namely: (i) Two-channel polaro-interferometric system irradiated by the femtosecond laser (~40 fs), (ii) spectroscopic measurements in the X-ray range, (iii) two-dimensional (2D)-resolved imaging of the Kα line emission from Cu, (iv) measurements of the ion emission by means of ion collectors, and (v) measurements of the volume of craters produced in a massive target providing information on the efficiency of the laser energy transfer to the shock wave. The 2D numerical simulations have been used to support the interpretation of experimental data. The general conclusion is that the fraction of the main laser beam energy deposited into the massive copper at two-beam irradiation decreases in comparison with the case of pre-plasma. The reason is that the pre-formed and expanding plasma deteriorates the efficiency of the energy transfer from the main laser pulse to a solid part of the targets by means of the fast electrons and the wave of an electron thermal conductivity.

The paper is directed to the study of high-temperature plasma and ablation plasma formation as well as efficiency of the laser energy transfer to solid targets irradiated by laser pulses with intensities of 1–50 PW/cm2 and duration of 200–300 ps, i.e., at conditions corresponding to the characteristics of the laser spike designed to generate the igniting shock wave in the shock ignition concept. The experiments have been performed at Prague Asterix Laser System. The iodine laser delivered 250 ps (full width at half maximum) pulses with the energy in the range of 100–600 J at the first (λ1 = 1.315 µm) and third (λ3 = 0.438 µm) harmonic frequencies. The focal spot radius of the laser beam on the surface of Al or Cu targets made was gradually decreased from 160 to 40 µm. The diagnostic data collected using three-frame interferometry, X-ray spectroscopy, and crater replica technique were interpreted by two-dimensional numerical and analytical modeling which included generation and transport of fast electrons. The coupling parameter Iλ2 was varied in the range of 1 × 1014−8 × 1016 Wμm2/cm2 covering the regimes of weak to intense fast electron generation. The dominant contribution of fast electron energy transfer into the ablation process and shock wave generation was found when using the first harmonic laser radiation, the focal spot radius of 40–100 µm, and the laser energy of 300–600 J.

In our earlier papers, we demonstrated that plasma pressure decreases with the growing atomic number of the target material. That experimentally confirmed fact brought about a question whether it would be possible to collimate the Al plasma outflow by using plastic plasma as a compressor. To prove that idea we used in our next experiments a plastic target with an Al cylindrical insert of 400 µm in diameter. The measurements were carried out at the Prague Asterix Laser System iodine laser facility. The laser provided a 250 ps (full width at half maximum (FWHM)) pulse with energy of 130 J at the third harmonic frequency (λ3 = 0.438 µm). The focal spot diameters (ΦL) 800, 1000, and 1200 µm ensured predominance of the plastic plasma amount high enough for the effective Al plasma compression. To study the Al plasma stream propagation and its interaction with plastic plasma a three-frame interferometric system and an X-ray camera were used. The experiment provided a proof that creation of the collimated Al plasma jet by action of outer plastic plasma is feasible. In order to discuss of the experimental results a thorough theoretical analysis was carried out.

Recent experimental results demonstrated that well formed plasma jets can be produced at laser interaction with targets made of materials with high atomic number (A ≥ 29 where A = 29 corresponds to Cu). On the contrary, it is impossible to launch a plasma jet on low-A material targets like plastic. This paper is aimed at explanation of this difference by considering mechanisms responsible for plasma jet formation, i.e., the radiative cooling of ablative plasma and the influence of target irradiation annular profile speculated hitherto, newly complemented by different expansion regimes of the Cu and plastic plasmas (provided by numerical simulations). The experiment was carried out with the PALS iodine laser. Two different planar massive targets, plastic and Cu, as well as the plastic target covered by thin Cu layers of various thicknesses were irradiated by the third harmonic laser beam of energy of 30 J, pulse duration of 250 ps (full width at half maximum), and the focal spot radius of 400 µm. To find the most suitable range of these layers (from 28 to 190 nm) a simple analytical model of laser-driven evaporation was developed. Three-frame laser interferometer and an X-ray streak camera were used as two main diagnostic tools. Numerical modeling was performed with the use of two-dimensional hydrodynamic code ATLANT-HE. Results provided from experiments and theoretical analyses have proved that the process of plasma jet formation is rather complex. Relative importance of the three mechanisms mentioned above depends on the target irradiation geometry as well as the target material used.

Interactions of sub-nanosecond pulses of kJ-class iodine laser “PALS” with low-density foams and acceleration of Al foils by the pressure of the heated foam matter are investigated here, both experimentally and theoretically. X-ray streak camera is used for evaluation of the speed of energy transfer through the porous foam material. The shock-wave arrival on the rear side of the target is monitored by optical streak camera. Accelerated foil velocities, measured by three-frame optical interferometers, and shadowgraphs, reach up to 107 cm/s. The accelerated foil shape is smooth without any signature of small-scale structures present in the incident laser beam. Conversion efficiencies as high as 14% of the laser energy into the kinetic energy of Al foil are derived. Experimental results compare well with our two-dimensional hydrodynamics simulations and with an approximate analytical model.

Hot electrons may significantly influence interaction of ultrashort laser pulses with solids. Accurate consideration of resonant absorption of laser energy and hot electron generation at a critical surface was achieved through the developed physical and mathematical models. A two-dimensional (2D) ray-tracing algorithm has been developed to simulate laser beam refraction and Bremsstrahlung absorption with allowance for nonlinear influence of a strong electromagnetic field. Hot electron transport was considered as a straight-line flow weakening by a friction force calculated in the approximation of the average state of ionization. Developed models were coupled with the 2D Lagrangian gas dynamic code “ATLANT” that takes into account nonlinear heat transport. The developed program has been applied to simulate irradiation of Al foils by picosecond laser double pulses. Hot electron transport and heating resulted in thin foil explosions. The transition from the exploding foil regime to the ablative one with foil thickening has been simulated and analyzed at various values of laser light intensity. In second series of calculations we have modeled the interaction of a nanosecond iodine laser with a two-layered target.