A current flowing between the ground and target exposed to the nanosecond laser radiation is analyzed to complete characteristics of laser ablation. Three phases of the target current are distinguished. During the ignition phase, the electron emission is driven by the laser pulse and the positive charge generated on the target is balanced by electrons coming from the ground through the target holder. At post-pulse times, a peaked waveform of the target current is typical for the active phase of the plasma and can give information on the material composition of the ablated surface layers. The afterglow phase is determined by a current of electrons flowing from the target to the ground. Experiment shows that the time-resolved target current is very sensitive to the actual composition of the surface layer of irradiated target and laser parameters.

This paper aims at investigation of efficiency of an ablative plasma energy transfer into a massive aluminum target using different atomic number ablators. For this reason, several target materials representing a wide range of atomic numbers (Z = 3.5–73) were used. The experiment was carried out at the iodine Prague Asterix Laser System. The laser provided a 250 ps pulse with energy of 130 J at the third harmonic frequency (λ3 = 0.438 μm). To study the plasma stream configurations a four-frame X-ray pinhole camera was used. The electron temperature of the plasma in the near-surface target region was measured by means of an X-ray spectroscopy. The efficiency of the plasma energy transport to the target was determined via the crater volume measurement using the crater replica technique. The experimental results were compared with two-dimensional numerical simulations where the plasma dynamics was based on the one-fluid, two temperature model, including radiation transport in diffusive approximation and ionization kinetics. It was shown that the plasma expansion geometry plays an important role in the ablative plasma energy transfer into the target.

The laser system PALS, as a driver of a broad-beam ion source, delivered deuterons which generated neutrons with energies higher than 14 MeV through the $\def \xmlpi #1{}\def \mathsfbi #1{\boldsymbol {\mathsf {#1}}}\let \le =\leqslant \let \leq =\leqslant \let \ge =\geqslant \let \geq =\geqslant \def \Pr {\mathit {Pr}}\def \Fr {\mathit {Fr}}\def \Rey {\mathit {Re}}{}^{7}\mathrm{Li(d,n)}{}^{8}\mathrm{Be}$ reaction. Deuterons with sub-MeV energy were accelerated from the front surface of a massive $\mathrm{CD}_{2}$ target in the backward direction with respect to the laser beam vector. Simultaneously, neutrons were emitted from the primary $\mathrm{CD}_{2}$ target and a secondary LiF catcher. The total maximum measured neutron yield from ${}^{2}\mathrm{D(d,n)}{}^{3}\mathrm{He}$, ${}^{7}\mathrm{Li(d,n)}{}^{8}\mathrm{Be}$, ${}^{12}\mathrm{C(d,n)}{}^{13}\mathrm{N}$ reactions was ${\sim } 3.5 ({\pm }0.5) \times 10^{8}\ \mathrm{neutrons/shot}$.

A massive deuterated polyethylene target was exposed to laser intensities of about 3 × 1016 W/cm2 employing the 3-TW Prague Asterix Laser System (PALS). We achieved a yield of 2 × 108 neutrons per laser shot. Average time-of-flight signals of scintillation detectors operated in current mode reveal broad energy spectra of fusion neutrons with dominating energy of about 2.45 MeV. The energy dependence of the neutron yield shows a consistency in results of nanosecond, picosecond and sub-picosecond experiments. Here we also show that ions emitted in the backward direction from the front target surface have a multi-peak energy spectrum, which is caused by burst emission mechanisms.

In our earlier papers, we demonstrated that plasma pressure decreases with the growing atomic number of the target material. That experimentally confirmed fact brought about a question whether it would be possible to collimate the Al plasma outflow by using plastic plasma as a compressor. To prove that idea we used in our next experiments a plastic target with an Al cylindrical insert of 400 µm in diameter. The measurements were carried out at the Prague Asterix Laser System iodine laser facility. The laser provided a 250 ps (full width at half maximum (FWHM)) pulse with energy of 130 J at the third harmonic frequency (λ3 = 0.438 µm). The focal spot diameters (ΦL) 800, 1000, and 1200 µm ensured predominance of the plastic plasma amount high enough for the effective Al plasma compression. To study the Al plasma stream propagation and its interaction with plastic plasma a three-frame interferometric system and an X-ray camera were used. The experiment provided a proof that creation of the collimated Al plasma jet by action of outer plastic plasma is feasible. In order to discuss of the experimental results a thorough theoretical analysis was carried out.