A compact high-power ultra-wideband bipolar pulse generator based on a modified Marx circuit is designed, which is mainly composed of a primary power supply, Marx generator, sharpening and cutoff subnanosecond spark gap switches, and coaxial transmission lines. The Marx generator with modified circuit structure has thirty-two stages and is composed of eight disk-like modules. Each module consists of four capacitors, two spark gap switches, four charging inductors, and a mechanical support. To simplify the design of the charging structure and reduce the number of switches, four groups of inductors are used to charge the capacitors of the Marx generator, two of which are used for positive voltage charging and the other two for negative voltage charging. When the capacitor of each stage is charged to 35 kV, the maximum output peak voltage can reach 1 MV when the Marx generator is open circuit. The high-voltage pulse generated by the Marx generator charges the transmission line and forms a bipolar pulse through sharpening and cutoff switches. All transmission lines used for bipolar pulse generation have an impedance of 10 Ω. When the 950 kV pulse voltage generated by the Marx generator is fed into the transmission line, the bipolar pulse peak voltage can reach 390 kV, the center frequency of the pulse is about 400 MHz, and the output peak power is about 15.2 GW.

This study aimed to investigate the structural and metabolic changes in cumulus cells of underweight women and their effects on oocyte maturation and fertilization. The cytoplasmic ultrastructure was analyzed by electron microscopy, mitochondrial membrane potential by immunofluorescence, and mitochondrial DNA copy number by relative quantitative polymerase chain reaction. The expression of various proteins including the oxidative stress-derived product 4-hydroxynonenal (4-HNE) and autophagy and apoptosis markers such as Vps34, Atg-5, Beclin 1, Lc3-I, II, Bax, and Bcl-2 was assessed and compared between groups. Oocyte maturation and fertilization rates were lower in underweight women (P < 0.05), who presented with cumulus cells showing abnormal mitochondrial morphology and increased cell autophagy. Compared with the mitochondrial DNA copies of the control group, those of the underweight group increased but not significantly. The mitochondrial membrane potential was similar between the groups (P = 0.8). Vps34, Atg-5, Lc3-II, Bax, and Bcl-2 expression and 4-HNE levels were higher in the underweight group compared with the control group (P < 0.01); however, the Bax/Bcl-2 ratio was lower in the underweight group compared with the control group (P = 0.031). Additionally, Beclin 1 protein levels were higher in the underweight group compared with the control group but without statistical significance. In conclusion, malnutrition and other conditions in underweight women may adversely affect ovulation, and the development, and fertilization of oocytes resulting from changes to the intracellular structure of cumulus cells and metabolic processes. These changes may lead to reduced fertility or unsatisfactory reproduction outcomes in women.

Toll-interacting protein (Tollip) participates in multiple biological processes. However, the biological functions of Tollip proteins in insects remain to be further explored. Here, the genomic sequence of tollip gene from Antheraea pernyi (named Ap-Tollip) was identified with a length of 15,060 bp, including eight exons and seven introns. The predicted Ap-Tollip protein contained conserved C2 and CUE domains and was highly homologous to those tollips from invertebrates. Ap-Tollip was highly expressed in fat body compared with other determined tissues. As far as the developmental stages were concerned, the highest expression level was found at the 14th day in eggs or the 3rd day of the 1st instar. Ap-Tollip was also obviously regulated by lipopolysaccharide, polycytidylic acid or 20E in different tissues. In addition, the interaction between Ap-Tollip and ubiquitin was confirmed by western blotting and pull-down assay. RNAi of Ap-Tollip significantly affected the expression levels of apoptosis and autophagy-related genes. These results indicated that Ap-Tollip was involved in immunity and development of A. pernyi.

The Huangshaping deposit is unique in southern Hunan Province, China, as it hosts economic reserves of both W–Mo and Pb–Zn mineralization, which are usually associated with granite and granodiorite porphyry in this area, respectively. This study reports results of in situ LA-MC-ICP-MS sulphur isotopic composition analyses conducted on sulphides from both W–Mo and Pb–Zn mineralization from the Huangshaping deposit with the aim of constraining ore genesis for this deposit. All samples from the proximal W–Mo mineralization have relatively uniform and high δ34S values (8.7 ‰ to 16.0 ‰), close to the range for carbonate sediments in this deposit (13.8 ‰ to 18.1 ‰). These patterns suggest that the granite porphyry in this deposit was the sulphur source for W–Mo mineralization, and that the assimilation of evaporite from the carbonate sediments led to the high δ34S values of the granite porphyry. Sulphides from the Pb–Zn mineralization have δ34S values (2.2 ‰ to 10.3 ‰) lower than those of the W–Mo mineralization, and generally increase in this paragenetic order, with the lowest δ34S values being similar to those of the basement (3.8 ‰ to 7.7 ‰). These patterns indicate that the original sulphur for the Pb–Zn mineralization was most likely derived from the basement, with input of sulphur from the carbonate sediments increasing during the evolution of ore-forming fluids. On the basis of the measured sulphur isotopic compositions, it is suggested that the ore-forming materials for the W–Mo mineralization were derived from the granite porphyry, whereas ore-forming materials extracted from the basement dominated the Pb–Zn mineralization.

Traditionally, the strata of the Luonie Valley, Dechang County, SW Sichuan, China, are considered to contain a suite of felsic volcanic rocks (the Huili Group) that erupted after c. 1050 Ma. However, we report here new age constraints, elemental and Lu–Hf isotope geochemistry for a different suite of older basaltic agglomerate lava, basaltic tuff lava and basalt from the same area, which we name the Luonie Formation. New dating results show that the basaltic volcanic suite of the upper part of the Luonie Formation formed at 1126.1 ± 9.9 Ma, significantly earlier than deposition of the Huili Group, but comparable in age to the 1142 ± 16 Ma Laowushan Formation in central Yunnan Province. Granite intrusion into the Luonie Formation dated 1050.7 ± 12.7 Ma provides crucial supporting evidence for this earlier depositional age. We also report a maximum sedimentary age of c. 1158 Ma for the underlying arkose, implying stratigraphic conformity with the basaltic volcanic rock suite.

The ϵHf(t) values of the basaltic volcanic rocks are mainly positive, indicating that the rocks are mainly derived from the depleted mantle and slightly stained by crustal materials. The characteristics of P*, Nb* and Zr* anomalies also support this view. The distribution patterns of trace and rare earth elements indicate that the basaltic volcanic rocks formed in an extensional setting. The Zr/4–Y–2Nb and Th–Nb/16–Zr/117 discrimination diagrams also provide evidence for this understanding. Lithofacies analysis shows that basaltic volcanic wrocks with the characteristics of both continental and marine facies should be formed in a littoral–neritic environment. We propose here that the evidence is consistent with a phase of continental extension that preceded the convergence of the SW Yangtze Block to form part of Rodinia.

Stimulated Raman-scattering-based lasers provide an effective way to achieve wavelength conversion. However, thermally induced beam degradation is a notorious obstacle to power scaling and it also limits the applicable range where high output beam quality is needed. Considerable research efforts have been devoted to developing Raman materials, with diamond being a promising candidate to acquire wavelength-versatile, high-power, and high-quality output beam owing to its excellent thermal properties, high Raman gain coefficient, and wide transmission range. The diamond Raman resonator is usually designed as an external-cavity pumped structure, which can easily eliminate the negative thermal effects of intracavity laser crystals. Diamond Raman converters also provide an approach to improve the beam quality owing to the Raman cleanup effect. This review outlines the research status of diamond Raman lasers, including beam quality optimization, Raman conversion, thermal effects, and prospects for future development directions.

Calcification within breast cancer is a diagnostically significant radiological feature that generally consists of hydroxylapatite. Samples from 30 cases of breast carcinoma with calcification were investigated using optical microscopy, energy-dispersive X-ray analysis, transmission-electron microscopy, Fourier-transform infrared spectroscopy, Raman spectroscopy, synchrotron radiation X-ray diffraction and X-ray fluorescence. Under optical microscopy, the calcifications were found to consist of either irregular aggregates with widths > 200 μm or spherical aggregates similar to psammoma bodies with an average diameter of 30 μm. Transmission-electron microscopy showed that short columnar or dumbbell-shaped crystals with widths of 10–15 nm and lengths of 20–50 nm were the most common morphology; spherical aggregates (~1 μm in diameter) with amorphous coatings of fibrous nanocrystals were also observed. Results indicated that hydroxylapatite was the dominant mineral phase in the calcifications, and both CO32– and cation substitutions (Na, Mg, Zn, Fe, Sr, Cu and Mn) were present in the hydroxylapatite structure. Fourier-transform infrared spectra show peaks at 872 and 880 cm–1 indicating that CO32– substituted both the OH– (A type) and PO43– (B type) sites of hydroxylapatite, making it an A and B mixed type. The ratio of B- to A-type substitution was estimated in the range of 1.1–18.7 from the ratio of peak intensities (I872/I880), accompanied with CO32– contents from 1.1% to 14.5%. Trace arsenic, detected in situ by synchrotron radiation X-ray fluorescence was found to be distributed uniformly in the calcifications in the form of AsO43– substituting for PO43–. It is therefore proposed that identifying these trace elements in breast cancer calcifications may be promising for future clinical diagnostics.

We consider the situation of a misalignment between the global temperature gradient and gravity in thermal convection. In such a case an effective horizontal buoyancy arises that will significantly influence the transport properties of heat, mass and momentum. It may also change the flow morphology in turbulent convection. In this paper, we present an experimental and numerical study, using Rayleigh–Bénard convection as a platform, to explore systematically the effect of horizontal buoyancy on heat transport in turbulent thermal convection. Experimentally, a condition of increasing horizontal Rayleigh number ($Ra_H$, which is the non-dimensional horizontal thermal driving strength) under fixed vertical Rayleigh number ($Ra_V$, the non-dimensional vertical driving strength) is achieved by tilting the convection cell and simultaneously increasing the imposed temperature difference. We find that, with increasing horizontal to vertical buoyancy ratio ($\varLambda = Ra_H/Ra_V$), the overall heat transport manifests a monotonic increase in vertical heat transport ($Nu_V$) as well as a monotonic increase in its horizontal component ($Nu_H$). However, the horizontal Nusselt number is found to be approximately one order of magnitude smaller than the vertical Nusselt for the parameter range explored. We also show that the non-zero $Nu_H$ results from the broken azimuthal symmetry of the system induced by the horizontal buoyancy. We find that the enhancement of vertical heat transport comes from the increased shear generated by the horizontal buoyancy at the boundary layer. The effect of Prandtl number ($Pr$) is also studied numerically. Finally, we extend the Grossmann–Lohse theory to the case with an effective horizontal buoyancy, the result of which is successful in predicting $Nu_V(Ra_V,\varLambda ,Pr)$.

Manganese (Mn) oxides have been prevalent on Earth since before the Great Oxidation Event and the Mn cycle is one of the most important biogeochemical processes on the Earth's surface. In sunlit natural environments, the photochemistry of Mn oxides has been discovered to enable solar energy harvesting and conversion in both geological and biological systems. One of the most widespread Mn oxides is birnessite, which is a semiconducting layered mineral that actively drives Mn photochemical cycling in Nature. The oxygen-evolving centre in biological photosystem II (PSII) is also a Mn-cluster of Mn4CaO5, which transforms into a birnessite-like structure during the photocatalytic oxygen evolution process. This phenomenon draws the potential parallel of Mn-functioned photoreactions between the organic and inorganic world. The Mn photoredox cycling involves both the photo-oxidation of Mn(II) and the photoreductive dissolution of Mn(IV/III) oxides. In Nature, the occurrence of Mn(IV/III) photoreduction is usually accompanied with the oxidative degradation of natural organics. For Mn(II) oxidation into Mn oxides, mechanisms of biological catalysis mediated by microorganisms (such as Pseudomonas putida and Bacillus species) and abiotic photoreactions by semiconducting minerals or reactive oxygen species have both been proposed. In particular, anaerobic Mn(II) photo-oxidation processes have been demonstrated experimentally, which shed light on Mn oxide emergence before atmospheric oxygenation on Earth. This review provides a comprehensive and up-to-date elaboration of Mn oxide photoredox cycling in Nature, and gives brand-new insight into the photochemical properties of semiconducting Mn oxides widespread on the Earth's surface.

With the progress in science and technology, hazardous chemicals are becoming more essential in chemical products, industrial and agricultural production, and daily life. Hazardous chemicals have poisoning, corrosive, explosive, and combusting natures; once on fire, they can trigger a chain of catastrophic incidences, resulting in casualties, property loss, and environmental pollution and posing hazards to life and property. Using the “8–12” explosion of the Ruihai Logistics warehouse in Tianjin Port (Binhai New District, China), the present study analyzes the characteristics of trauma of the casualties in this accident and the emergency medical rescue strategies. The goals were to improve the ability of emergency rescue in such accidents and to save people’s lives and property to the maximum extent.

Since the outbreak of 2019 novel coronavirus (2019-nCoV) infection in Wuhan City, China, pediatric cases have gradually increased. It is very important to prevent cross-infection in pediatric fever clinics, to identify children with fever in pediatric fever clinics, and to strengthen the management of pediatric fever clinics. According to prevention and control programs, we propose the guidance on the management of pediatric fever clinics during the nCoV pneumonia epidemic period, which outlines in detail how to optimize processes, prevent cross-infection, provide health protection, and prevent disinfection of medical staff. The present consideration statement summarizes current strategies on the pre-diagnosis, triage, diagnosis, treatment, and prevention of 2019-nCoV infection, which provides practical suggestions on strengthening the management of pediatric fever clinics during the nCoV pneumonia epidemic period.

Recent studies have demonstrated that the nutritional properties of peanut meal (PM) can be improved after being fermented. The assessment of fermented PM has been reported to be limited to various physical and chemical evaluations in vitro. In the present study, PM was fermented by Bacillus natto to explore the effects of fermented PM extract (FE) on growth performance, learning and memory ability and intestinal microflora in mice. Ninety newly weaned male Kunming (KM) mice were randomly divided into seven groups: normal group (n 20), low-dose FE group (n 10), middle-dose FE group (MFE) (n 10), high-dose FE group (HFE) (n 20), unfermented extraction group (n 10), model group (10) and natural recovery group (10). Learning and memory skills were performed by the Morris water maze (MWM) test, and the variation in gut microbiota (GM) composition was assessed by 16S rDNA amplicon sequencing. The results show that HFE remarkably improved the growth performance in mice. In the MWM test, escape latency was shortened in both MFE and HFE groups, while the percentage of time, distance in target quadrant and the number crossing over the platform were significantly increased in the HFE group. Moreover, the FE played a preventive role in the dysbacteriosis of mice induced by antibiotic and increased the richness and species evenness of GM in mice.

We report direct numerical simulation results that clearly elucidate the mechanism that leads to curvature dependence of drag enhancement (DE) in viscoelastic turbulent Taylor–Couette flow. Change in the angular momentum transport and its inherent link to transitions in vortical flow structures have been explored to depict the influence of the curvature of the flow geometry on DE. Specifically, it has been demonstrated that a transition in vortical structures with increasing radius ratio leads to weakening and elimination of the small-scale Görtler vortices and development and better organization (occupying the entire gap) of large-scale Taylor vortices as also evinced by the patterns of angular momentum current. The commensurate change in DE and its underlying mechanism are examined by contributions of convective flux and polymeric stress to the angular momentum current. The present finding paves the way for capturing highly localized elastic turbulence structures in direct numerical simulation by increasing geometry curvature in traditional turbulent curvilinear flows.

Seasonal influenza virus epidemics have a major impact on healthcare systems. Data on population susceptibility to emerging influenza virus strains during the interepidemic period can guide planning for resource allocation of an upcoming influenza season. This study sought to assess the population susceptibility to representative emerging influenza virus strains collected during the interepidemic period. The microneutralisation antibody titers (MN titers) of a human serum panel against representative emerging influenza strains collected during the interepidemic period before the 2018/2019 winter influenza season (H1N1-inter and H3N2-inter) were compared with those against influenza strains representative of previous epidemics (H1N1-pre and H3N2-pre). A multifaceted approach, incorporating both genetic and antigenic data, was used in selecting these representative influenza virus strains for the MN assay. A significantly higher proportion of individuals had a ⩾four-fold reduction in MN titers between H1N1-inter and H1N1-pre than that between H3N2-inter and H3N2-pre (28.5% (127/445) vs. 4.9% (22/445), P < 0.001). The geometric mean titer (GMT) of H1N1-inter was significantly lower than that of H1N1-pre (381 (95% CI 339–428) vs. 713 (95% CI 641–792), P < 0.001), while there was no significant difference in the GMT between H3N2-inter and H3N2-pre. Since A(H1N1) predominated the 2018–2019 winter influenza epidemic, our results corroborated the epidemic subtype.

In the era of knowledge networking, the structure and production mode of knowledge are constantly changing. This article creatively introduces the knowledge mapping method in design research, and based on the perspective of the National Natural Science Foundation of China (NSFC) to compile literature, uses word frequency analysis, co-word analysis, and citation analysis to construct knowledge graphs of design science. This study graphically shows the distribution and flow law of knowledge within design discipline and probes into the research frontier and evolution trend of Chinese design science.

Liquid films can be entrained when the dewetting velocity attains a threshold, and this dynamical wetting transition has been well studied in the situation of plane substrates. We investigate the forced dewetting in a capillary tube using diffuse-interface simulations and lubrication analysis, focusing on the onset of wetting transition and subsequent interface evolution. Results show that the meniscus remains stable when the displacing rate is below a threshold, beyond which film entrainment occurs and eventually leads to the formation of Taylor bubbles separated by liquid slugs, as has also been observed in the recent experiments of Zhao et al. (Phys. Rev. Lett., vol. 120, 2018, 084501). We derive an analytical solution of the critical capillary number, and demonstrate that the wetting transition is accompanied by a vanishing apparent contact angle and an abrupt drop of the contact-line velocity. Both the bubble and slug lengths are found to depend on the capillary number and the wettability of the wall. A theoretical formula for the bubble length is also proposed and compares favourably with numerical and experimental results.