The paper is aimed at optimization of parameters of a copper plasma jet produced at the DPF-1000U device, in which the inner electrode face was conically shaped. Preliminary information was obtained by numerical simulations of the plasma jet creation for different copper cones with the use of the two-dimensional magneto-hydrodynamic code KAROL. The simulations suggested that the cone height in the range of 4–7 cm should ensure a good plasma jet quality. The experimental data delivered by means of a 16-frame laser interferometer and a four-frame X-ray pinhole camera fully confirmed this conclusion. In the paper, we demonstrate the results for a 5 cm height cone. The eroded Cu plasma, swept up by the deuterium plasma sheath, was accelerated axially and compressed to very small diameter (3 mm) with an electron density of 7 × 1018 cm−3. The Cu plasma jet achieved a velocity of 5 × 107 cm/s and reached in the period of about 230 ns a distance (length) of 7 cm. The above results prove a successful adaptation of the plasma focus device to the metallic plasma jet generator.

This paper aims at a test of a plasma focus (PF) device as a metallic plasma jet generator. The experiment was carried out at the DPF-1000U device in which the inner electrode face was conically shaped. Deuterium (D2) with the initial pressure of 0.9 Torr was used as a filling gas. In the experiment, a metallic plasma was ensured due to erosion of the inner electrode during a PF discharge. To create the metallic plasma jet, the eroded copper (Cu) plasma, swept by the deuterium plasma sheath, was accelerated axially and compressed to very small radius (about 1–2 mm). The Cu plasma jet achieved a velocity of 3 × 107 cm/s. To study processes of the plasma jet creation and propagation a 16-frame laser interferometer and a four-frame X-ray pinhole camera were used. Recorded images prove a successful adaptation of the PF device to the metallic plasma jet generator.

This paper aims at investigation of efficiency of an ablative plasma energy transfer into a massive aluminum target using different atomic number ablators. For this reason, several target materials representing a wide range of atomic numbers (Z = 3.5–73) were used. The experiment was carried out at the iodine Prague Asterix Laser System. The laser provided a 250 ps pulse with energy of 130 J at the third harmonic frequency (λ3 = 0.438 μm). To study the plasma stream configurations a four-frame X-ray pinhole camera was used. The electron temperature of the plasma in the near-surface target region was measured by means of an X-ray spectroscopy. The efficiency of the plasma energy transport to the target was determined via the crater volume measurement using the crater replica technique. The experimental results were compared with two-dimensional numerical simulations where the plasma dynamics was based on the one-fluid, two temperature model, including radiation transport in diffusive approximation and ionization kinetics. It was shown that the plasma expansion geometry plays an important role in the ablative plasma energy transfer into the target.

This paper reports on properties of a plasma formed by sequential action of two laser beams on a flat target, simulating the conditions of shock-ignited inertial confinement fusion target exposure. The experiments were performed using planar targets consisting of a massive copper (Cu) plate coated with a thin plastic (CH) layer, which was irradiated by the 1ω PALS laser beam (λ = 1.315 μm) at the energy of 250 J. The intensity of the fixed-energy laser beam was scaled by varying the focal spot radius. To imitate shock ignition conditions, the lower-intensity auxiliary 1ω beam created CH-pre-plasma which was irradiated by the main beam with a delay of 1.2 ns, thus generating a shock wave in the massive part of the target. To study the parameters of the plasma treated by the two-beam irradiation of the targets, a set of various diagnostics was applied, namely: (i) Two-channel polaro-interferometric system irradiated by the femtosecond laser (~40 fs), (ii) spectroscopic measurements in the X-ray range, (iii) two-dimensional (2D)-resolved imaging of the Kα line emission from Cu, (iv) measurements of the ion emission by means of ion collectors, and (v) measurements of the volume of craters produced in a massive target providing information on the efficiency of the laser energy transfer to the shock wave. The 2D numerical simulations have been used to support the interpretation of experimental data. The general conclusion is that the fraction of the main laser beam energy deposited into the massive copper at two-beam irradiation decreases in comparison with the case of pre-plasma. The reason is that the pre-formed and expanding plasma deteriorates the efficiency of the energy transfer from the main laser pulse to a solid part of the targets by means of the fast electrons and the wave of an electron thermal conductivity.

The paper is directed to the study of high-temperature plasma and ablation plasma formation as well as efficiency of the laser energy transfer to solid targets irradiated by laser pulses with intensities of 1–50 PW/cm2 and duration of 200–300 ps, i.e., at conditions corresponding to the characteristics of the laser spike designed to generate the igniting shock wave in the shock ignition concept. The experiments have been performed at Prague Asterix Laser System. The iodine laser delivered 250 ps (full width at half maximum) pulses with the energy in the range of 100–600 J at the first (λ1 = 1.315 µm) and third (λ3 = 0.438 µm) harmonic frequencies. The focal spot radius of the laser beam on the surface of Al or Cu targets made was gradually decreased from 160 to 40 µm. The diagnostic data collected using three-frame interferometry, X-ray spectroscopy, and crater replica technique were interpreted by two-dimensional numerical and analytical modeling which included generation and transport of fast electrons. The coupling parameter Iλ2 was varied in the range of 1 × 1014−8 × 1016 Wμm2/cm2 covering the regimes of weak to intense fast electron generation. The dominant contribution of fast electron energy transfer into the ablation process and shock wave generation was found when using the first harmonic laser radiation, the focal spot radius of 40–100 µm, and the laser energy of 300–600 J.

In our earlier papers, we demonstrated that plasma pressure decreases with the growing atomic number of the target material. That experimentally confirmed fact brought about a question whether it would be possible to collimate the Al plasma outflow by using plastic plasma as a compressor. To prove that idea we used in our next experiments a plastic target with an Al cylindrical insert of 400 µm in diameter. The measurements were carried out at the Prague Asterix Laser System iodine laser facility. The laser provided a 250 ps (full width at half maximum (FWHM)) pulse with energy of 130 J at the third harmonic frequency (λ3 = 0.438 µm). The focal spot diameters (ΦL) 800, 1000, and 1200 µm ensured predominance of the plastic plasma amount high enough for the effective Al plasma compression. To study the Al plasma stream propagation and its interaction with plastic plasma a three-frame interferometric system and an X-ray camera were used. The experiment provided a proof that creation of the collimated Al plasma jet by action of outer plastic plasma is feasible. In order to discuss of the experimental results a thorough theoretical analysis was carried out.

Our earlier papers demonstrate a very simple method of plasma jet formation, consisting in irradiating a massive planar target of a relatively high atomic number by a partly defocused laser beam. Our present interest is concentrated on interaction of the plasma jet with other media. This paper is aimed at investigations of interaction of two jets launched successively on Cu target. Our attention was paid to the role of radiative cooling in the plasma jet formation. The experiment was carried out at the PALS iodine laser facility. The laser provided a 250-ps (full width at half maximum) pulse with energy of 130 J at the third harmonic frequency (λ3 = 0.438 µm). Two successive jets were produced on a massive flat Cu target provided with a cylindrical channel 5 mm long and 400 µm in diameter. Since the focal spot diameter of the laser beam on the target surface was larger than that of the channel (800 µm), the annular irradiation of the target face resulted in creation of the first plasma jet, whereas the second jet was produced by action of the central part of laser beam on the channel wall. Three-frame interferometric system, X-ray streak camera, and a set of ion collectors were used as diagnostic tools.

Recent experimental results demonstrated that well formed plasma jets can be produced at laser interaction with targets made of materials with high atomic number (A ≥ 29 where A = 29 corresponds to Cu). On the contrary, it is impossible to launch a plasma jet on low-A material targets like plastic. This paper is aimed at explanation of this difference by considering mechanisms responsible for plasma jet formation, i.e., the radiative cooling of ablative plasma and the influence of target irradiation annular profile speculated hitherto, newly complemented by different expansion regimes of the Cu and plastic plasmas (provided by numerical simulations). The experiment was carried out with the PALS iodine laser. Two different planar massive targets, plastic and Cu, as well as the plastic target covered by thin Cu layers of various thicknesses were irradiated by the third harmonic laser beam of energy of 30 J, pulse duration of 250 ps (full width at half maximum), and the focal spot radius of 400 µm. To find the most suitable range of these layers (from 28 to 190 nm) a simple analytical model of laser-driven evaporation was developed. Three-frame laser interferometer and an X-ray streak camera were used as two main diagnostic tools. Numerical modeling was performed with the use of two-dimensional hydrodynamic code ATLANT-HE. Results provided from experiments and theoretical analyses have proved that the process of plasma jet formation is rather complex. Relative importance of the three mechanisms mentioned above depends on the target irradiation geometry as well as the target material used.

Interactions of laser driven plasma jets with He and Ar gas puffs was investigated experimentally by means of three-frame interferometric/shadowgraphic system and three-frame X-ray pinhole camera. A defocused iodine laser beam using the Prague Asterix Laser System (PALS) interacting with massive planar Cu targets generated high-speed well-collimated plasma jets. The PALS third harmonic (0.438 µm), with pulse duration of 250 ps (full width at half maximum), and energy of 100 J was employed in two irradiation geometries: with an incidence normal to the target surface and with an oblique one (30° with respect to the target normal), in order to minimize the heating of the ambient gas by the laser beam. The results of these interaction experiments, in particular, those obtained in case of the oblique incidence geometry, are presented and discussed. They show the effect of the double shock formation in ambient gases: starting by the ablative plasma action, followed by that of the jet.

This paper is devoted to investigations of laser energy transfer into solid targets with respect to the focusing lens focal point position relative to the solid target surface as obtained at the PALS laser facility. The third harmonic of the PALS laser beam with energy ~90 J and pulse duration ~250 ps (FWHM) was used for irradiation of two kinds of targets made of Cu: a slab and a 3.6 µm thick foil. The focal point of the beam was located either inside or in front of the target surface, and care was taken to ensure the same laser spot radii in both cases (250 µm). It was demonstrated that these two opposite focal point positions give rise to significantly different laser-plasma interactions: with either depression or maximum of the laser intensity distribution in the center of the beam, respectively. It was also verified that the focal point position inside of the target is favorable for plasma jets creation, whereas the opposite case is more effective for acceleration of flyers.

Intense laser-beam interactions with preformed plasma, preceding the laser-target interactions, significantly influence both the ion and X-ray generation. It is due to the laser pulse (its total length, the shape of the front edge, its background, the contrast, the radial homogeneity) as well as plasma (density, temperature) properties. Generation of the super fast (FF) ion groups is connected with a presence of non-linear processes. Saturated maximum of the charge states (independently on the laser intensity) is ascribed to the constant limit radius of the self-focused laser beam. Its longitudinal structure is considered as a possible explanation for the course of some experimental dependencies obtained.

Our recent experimental results demonstrate that the formation of plasma jets is a fundamental process accompanying the laser produced plasma expansion, if a massive planar target with relatively high atomic number is irradiated by a defocused laser beam. In this paper some new results on the influence of target irradiation conditions on plasma jet parameters are presented. The experiment was carried out at the PALS iodine laser facility, with the third harmonic beam of the pulse duration of 250 ps (FWHM). The beam energies varied in the range of 13–160 J, the focal spot radii in the range of 35–600 µm. The planar massive targets used in the experiment were made of Cu, Ag and Ta. For measurements of the electron density evolution a three frame interferometric system was employed. The jets were observed in the whole range of the laser energy used. The initial velocities of the plasma jets produced in the reported experiment reached the value of up to 7·107 cm/s, the jets were up to 4 mm long including the jet pedestal and about 400 µm in diameter. Calculations of the efficiency of the plasma jet production show that it decreases with increasing the laser energy.

Interactions of sub-nanosecond pulses of kJ-class iodine laser “PALS” with low-density foams and acceleration of Al foils by the pressure of the heated foam matter are investigated here, both experimentally and theoretically. X-ray streak camera is used for evaluation of the speed of energy transfer through the porous foam material. The shock-wave arrival on the rear side of the target is monitored by optical streak camera. Accelerated foil velocities, measured by three-frame optical interferometers, and shadowgraphs, reach up to 107 cm/s. The accelerated foil shape is smooth without any signature of small-scale structures present in the incident laser beam. Conversion efficiencies as high as 14% of the laser energy into the kinetic energy of Al foil are derived. Experimental results compare well with our two-dimensional hydrodynamics simulations and with an approximate analytical model.

The paper presents results of investigations of the process of the creation of a diamagnetic cavity by a laser-produced plasma in a strong transverse magnetic field of 10 T in induction. The plasma was produced from a flat, teflon target by an Nd laser of 5 J in energy and about 1 ns in pulse duration. The investigations were carried on by means of a three-frame interferometry and a non-contact magnetic probe, a so called remote magnetic probe (RMP). For the needs of this work, we developed a methodology for the measurement of the dimensions of the cavity during its expansion by means of the RMP, taking into account the plasma expansion geometry that is specific to flat targets. The dynamics of the process of creation of the diamagnetic cavity, its shape and dimensions have been determined. A very good consistency of dimensions of the diamagnetic cavity and plasma boundary in their quasisteady state, obtained with both diagnostics, allows us to apply the RMP method not only for the investigation of diamagnetic properties of various laser-produced plasmas, but also for the evaluation of their initial kinetic energy and its transformation in magnetic field.

We present results of studies of the behavior of a laser-produced plasma in a strong external transverse magnetic field of above 10 T in induction generated from a flat teflon target at the laser power densities of about 1014 W/cm2. In the measurements of plasma parameters, a two-channel automated interferometric system (Pisarczyk et al. 1994) was applied. The interferometric measurements have shown that the transverse magnetic field induces an asymmetry of the plasma distinctly apparent in the interferograms registered in two mutually perpendicular directions. Due to the lack of axial symmetry of the plasma, the Abel's transformation could not be applied in quantitative processing of the interferograms. To reconstruct a spatial distribution of electron density in a plasma stream of disturbed axial symmetry, a methodology prepared for this experiment was used. Analyzing the spatial and temporal distributions of electron concentration obtained in the transverse magnetic field, it has been proved that the factor responsible for the disturbance of the axial symmetry of the plasma is the Rayleigh–Taylor (R–T) instability corresponding to the ion unmagnetization state.