Hostname: page-component-7c8c6479df-r7xzm Total loading time: 0 Render date: 2024-03-29T11:34:36.578Z Has data issue: false hasContentIssue false

On the effects of temperature on the strength of H2SO4-doped ice single crystals

Published online by Cambridge University Press:  08 September 2017

Xiang Li
Affiliation:
Thayer School of Engineering, Dartmouth College, Hanover, New Hampshire 03755-8000, USA E-mail: ian.baker@dartmouth.edu
Daniel Iliescu
Affiliation:
Thayer School of Engineering, Dartmouth College, Hanover, New Hampshire 03755-8000, USA E-mail: ian.baker@dartmouth.edu
Ian Baker
Affiliation:
Thayer School of Engineering, Dartmouth College, Hanover, New Hampshire 03755-8000, USA E-mail: ian.baker@dartmouth.edu
Rights & Permissions [Opens in a new window]

Abstract

Previously, it was shown that the reduction in peak stress of single crystal ice at −20°C due to H2SO4, Δσ, could be described by Δσ = kC1/2, where C is the sulfuric acid concentration and k is a constant. Here we show that the strength reduction due to H2SO4 is more general and that the reduction is greater as the temperature decreases. Δσ was again found to be proportional to C1/2 at −10°C, but k at −10°C was significantly less than at −20°C.

Type
Research Article
Copyright
Copyright © International Glaciological Society 2009

Introduction

In ice Ih, adjacent (0001) slip planes are connected via randomly oriented hydrogen bonds. Reference GlenGlen (1968) suggested that this proton disorder presents the major obstacle to dislocation motion and, thus, for a dislocation to glide, the hydrogen bonds need to be appropriately oriented. This bond reorientation takes place by the movement of H3O+ and OH ions and L- and D-Bjerrum defects. Hence, the introduction of extrinsic point defects into ice, by the addition of soluble impurities, should increase dislocation mobility and make the ice softer. While measurements on increased dislocation mobility in doped ice have produced either negative or inconclusive results (Reference Maï, Perez, Tatibouët and VassoilleMaï and others, 1978; Reference Shearwood and WhitworthShearwood and Whitworth, 1992; Reference Hu, Jia, Liu, Baker and BlackHu and others, 1995), impurities do appear to increase the dislocation density in ice, although it is not clear why (Reference Jones and GilraJones and Gilra, 1972, Reference Jones, Gilra, Whalley, Jones and Gold1973a,Reference Jones and Gilrab; Reference Oguro and HigashiOguro, 1988; Reference Hu, Jia, Liu, Baker and BlackHu and others, 1995; Reference Trickett, Baker and PradhanTrickett and others, 2000). Several studies have clearly shown that small concentrations (a few ppm) of the acids HF, HCl and H2SO4 decrease the strength of ice single crystals dramatically (Reference JonesJones, 1967; Reference Jones and GlenJones and Glen, 1969; Reference Nakamura and JonesNakamura and Jones, 1970, 1973; Reference Trickett, Baker and PradhanTrickett and others, 2000) and, at least for H2SO4, that this leads to a concomitant increase in ductility (Reference Trickett, Baker and PradhanTrickett and others, 2000).

H2SO4 is of interest since it is present in natural ice, arising from aerosols produced by volcanoes and anthropogenic sources. In recent work, we demonstrated that at −20°C, even though H2SO4 decreases the strength of ice single crystals, it has no effect on the stress exponent, n, in the relationship between the shear strain rate, , and peak shear stress, τ, i.e. (Reference Baker, Trickett, Pradhan, Maltman, Hubbard and HambreyBaker and others, 2000). It was also shown that at −20°C the reduction in peak resolved shear stress (RSS) due to the presence of H2SO4, Δσ , was related to the concentration, C, through Δσ = kC 1/2, where k is a constant (Reference Trickett, Baker and PradhanTrickett and others, 2000). In this paper, we extend our previous work on the effects of doping on ice single crystals and describe the effects of doping with H2SO4 on n and k at −10°C and −30°C.

Experimental

Both high-purity ice crystals and H2SO4-doped ice crystals were grown in a cold room at the Ice Research Laboratory, Thayer School of Engineering, Dartmouth College. All the doped ice crystals were made from deionized water mixed with H2SO4 in 5 gal (20 L) Nalgene tanks. The concentration of H2SO4 in each specimen was determined after mechanical testing by melting the specimen and measuring the pH of the resulting solution with a probe calibrated in the range of interest. The water-filled tanks were placed in a 1–2°C cold room for 24 hours to equilibrate the water temperature; 24 hours is a good time in which to get bubble-free ice. After equilibration, the cold-room temperature was changed to −2°C for 10 days. The sides and the bottom of the tank were insulated with Armaflex foam in order to minimize the radial heat exchange and to force the ice to grow more-or-less unidirectionally from the open top. Large ice pucks (28 cm diameter, 13 cm high) of various concentrations of H2SO4 were grown. Each puck contained three to five large crystals with the c axes oriented quasi-parallel to the growth direction, which was downward. The same method was used to grow undoped ice. Polarized illumination was used to identify and trace the boundaries of the large crystals (Reference HobbsHobbs, 1974), and eventually the large single crystals were cut out using a precision bandsaw. If needed, the ice was stored in plastic bags and put in a −10°C cold room.

After an ice single crystal was chosen, its orientation was further examined by etch-pitting with a Formvar solution (Reference HiguchiHiguchi, 1958). The oriented grains were then cut out using a bandsaw to have the basal plane (marked with a hexagon in Fig. 1) tilted either at 45° or 3° from the top surface, with () planes on the side surface. The final orientation of the single crystal was confirmed by cutting a thin section cut from one end and analyzing it using the Rigby stage.

Fig. 1. The dimensions and orientation of the ice single crystals. The plane with a hexagon indicates the orientation of the basal plane, which was tilted to either θ = 45° or θ = 3° from the top surface.

A horizontal milling machine was used to shape the surfaces of specimens to obtain a final sample of 20 mm × 25 mm × 60 mm.

All mechanical tests were performed at a constant strain rate using a hydraulic MTS uniaxial testing machine located in a cold room. Two sets of tests were performed. First, both for crystals containing 3.2 ppm H2SO4 and for the undoped ice, tests were performed over a range of strain rates from 3 × 10−7 s−1 to 3 × 10−4 s−1 at −10°C and −30°C. In all these tests the single crystals had the basal plane angle θ = 45°. Second, at −10°C, tests were performed on crystals with four different concentrations of H2SO4 under an axial strain rate of 1 × 10−5 s−1. All these tests had the basal plane angle θ = 3° for direct comparison to previous tests by Reference Trickett, Baker and PradhanTrickett and others (2000). LabVIEW data acquisition software was used to collect the load and displacement from the tests. The strain-rate error was approximately ±2% and the measured peak stress was accurate to within ±5%.

Results and Discussion

Figure 2 shows the RSS on the basal plane plotted against shear strain for compression tests at −10°C and −30°C performed at different axial strain rates for high-purity ice crystals and H2SO4-doped ice crystals. All these tests were performed with the basal plane tilted to 45°. Common to all tests, the curves show a linearly rising stress followed by a sharply declining stress after a peak, the decline in stress decreasing with increasing strain. The curves demonstrate dramatic decreases in peak stress and subsequent flow stress with decreasing strain rate. The peak stress and subsequent flow stresses are much higher at −30°C for a given strain rate than those at −10°C.

Fig. 2. Typical RSS–shear-strain curves at various axial strain rates (shown in s−1) for high-purity ice single crystals with the c axis at 45° to the loading direction at −10°C (a); for ice single crystals doped with 3.2 ppm H2SO4 with the c axis at 45° to the loading direction at −10°C (b); for high-purity ice single crystals with the c axis at 45° to the loading direction at −30°C (c); and for ice single crystals doped with 3.2 ppm H2SO4 with the c axis at 45° to the loading direction at −30°C (d).

The stress exponent, n, was obtained by linear regression from plots of or log , where is the shear strain rate and τ is the corresponding maximum RSS at constant temperature. Figure 3 is a logarithmic plot of resolved shear strain rate versus peak RSS for the data obtained here at −10°C and −30°C, and for data at −20°C from Reference Baker, Trickett, Pradhan, Maltman, Hubbard and HambreyBaker and others (2000).

Fig. 3. Graph on log–log scales, of shear strain rate versus peak stress, showing a comparison between the n values (slopes) of undoped and H2SO4-doped ice single crystals at different temperatures. The data at −20°C are from Reference Trickett, Baker and PradhanTrickett and others (2000) and are for 3.4 ppm H2SO4 (not 6.8 ppm as noted in that publication).

Three important points need to be emphasized. First, at any given temperature the strength is decreased by the addition of H2SO4 (cf. Fig. 2a and b and Fig. 2c and d). This can also be clearly seen in Figure 4 which compares the RSS–shear-strain curves for high-purity and H2SO4-doped (3.2 ppm) ice single crystals with θ = 45° when tested with an axial strain rate of 1 × 10−5 s−1 at −30°C. Second, for a particular temperature, the stress exponent is unaffected by doping. Third, the stress exponent appears to increase slightly with decreasing temperature, i.e. from 1.81–1.82 at −10°C to 1.93 at −20°C (Reference Baker, Trickett, Pradhan, Maltman, Hubbard and HambreyBaker and others, 2000) and 2.0–2.03 at −30°C. These n values are close to those obtained by Reference Jones and BrunetJones and Brunet (1978), who performed constant strain-rate compression tests on single crystals. In their work, n = 2.01 ± 0.04 at −10°C and n = 2.07 ± 0.08 at −20°C.

Fig. 4. RSS–shear-strain curves for high-purity and 3.2 ppm H2SO4-doped ice single crystals with θ = 45° at an axial strain rate of 1 × 10−5 s−1 at −30°C.

In order to further examine the weakening effect, ice single crystals doped with various concentrations of H2SO4 were strained under compression at constant strain rate in order to obtain the relationship between the reduction in strength due to H2SO4 and the dopant level. Tests were performed at −10°C on single crystal specimens with the basal plane tilted to 3° for direct comparison to previous tests at −20°C (Reference Trickett, Baker and PradhanTrickett and others, 2000). Figure 5 clearly shows that the higher the dopant level, the softer is the doped ice.

Fig. 5. Comparison between the RSS–shear-strain curves for high-purity ice single crystals and ice single crystals doped with various concentrations of H2SO4. The basal plane orientation is θ = 3°; axial strain rate = 1 × 10−5 s−1; temperature = −10°C. The curves are offset along the strain axis.

There are two possible explanations for this softening. The H2SO4 may increase the dislocation mobility due to the addition of two H+ ions from each H2SO4 molecule (Reference GlenGlen, 1968), or it may increase the grown-in dislocation density (Reference Trickett, Baker and PradhanTrickett and others, 2000). The difference between the critical RSS for high-purity ice and that for H2SO4-doped ice at −10°C is plotted as a function of C 1/2, where C is the concentration of H2SO4 (Fig. 6). Data at −20°C from Reference Trickett, Baker and PradhanTrickett and others (2000) are shown for comparison; note that the data in that publication have H2SO4 concentrations a factor of two too large, i.e. they are actually extrinsic H3O+ concentrations.

Fig. 6. Comparison of the reduction in peak RSS difference, Δσ, versus C 1/2 in ice single crystals compressed at −10°C and −20°C normalized to a shear strain rate of 1 × 10−5 s−1. The data at −20°C are from Reference Trickett, Baker and PradhanTrickett and others (2000).

It is evident from Figure 6 that the softening effect at −10°C is less than half that at −20°C. This is consistent with Glen’s model (Reference GlenGlen, 1968), i.e. the softening from H2SO4 arises from the extrinsic H3O+ ions, which aid dislocation motion, and these extrinsic ions constitute a smaller proportion of the total H3O+ ion concentration, i.e. extrinsic plus thermally produced (intrinsic), at −10°C. A final point concerns the scatter in the data in Figure 6. This may have two causes. First, slight misorientations in crystal orientation could affect the strength. Second, there are undoubtedly variations in H2SO4 concentrations within each single crystal.

Conclusions

It has been shown that H2SO4 decreases the strength of ice crystals at −10°C and −30°C but does not affect the stress exponent. The decrease in peak stress due to H2SO4 is proportional to the square root of the sulfuric acid concentration, with the decrease in strength being greater at −20°C than at −10°C. The results are consistent with Glen’s model for dislocation motion in ice, but other effects of impurities or dislocations (e.g. increasing their density) cannot be excluded.

Acknowledgements

This research was supported by US National Science Foundation (NSF) grants OPP-0738975 and OPP-0440523 and US Army Research Office (ARO) grants DAAD 19-00-1-0444 and 51065-EV. The views and conclusions contained herein are those of the authors and should not be interpreted as representing official policies, either expressed or implied, of the NSF, ARO or the US Government.

References

Baker, I., Trickett, Y.L. and Pradhan, P.M.S.. 2000. The effect of H2SO4 on the stress exponent in ice single crystals. In Maltman, A.J., Hubbard, B. and Hambrey, M.J., eds. Deformation of glacial materials. London, Geological Society, 3945. (Special Publication 176.)Google Scholar
Glen, J.W. 1968. The effect of hydrogen disorder on dislocation movement and plastic deformation of ice. Phys. Kondens. Mater., 7(1), 4351.Google Scholar
Higuchi, K. 1958. The etching of ice crystals. Acta Metall., 6(10), 636642.CrossRefGoogle Scholar
Hobbs, P.V. 1974. Ice physics. Oxford, etc., Clarendon Press.Google Scholar
Hu, X., Jia, K., Liu, P., Baker, I. and Black, D.. 1995. Dislocation mobility in HCl-doped ice. Mater. Res. Soc. Symp. Proc., 375, 287292.CrossRefGoogle Scholar
Jones, S.J. 1967. Softening of ice crystals by dissolved fluoride ions. Phys. Lett., 25(5), 366367.Google Scholar
Jones, S.J. and Brunet, J.G.. 1978. Deformation of ice single crystals close to the melting point. J. Glaciol., 21(85), 445455.CrossRefGoogle Scholar
Jones, S.J. and Gilra, N.K.. 1972. Increase of dislocation density in ice by dissolved hydrogen fluoride. Appl. Phys. Lett., 20(8), 319320.Google Scholar
Jones, S.J. and Gilra, N.K.. 1973a. Dislocations in ice observed by X-ray topography. In Whalley, E., Jones, S.J. and Gold, L.W., eds. Physics and chemistry of ice. Ottawa, Ont., Royal Society of Canada, 344349.Google Scholar
Jones, S.J. and Gilra, N.K.. 1973b. X-ray topographical study of dislocations in pure and HF-doped ice. Philos. Mag., 27(2), 457472.Google Scholar
Jones, S.J. and Glen, J.W.. 1969. The effect of dissolved impurities on the mechanical properties of ice crystals. Philos. Mag., 19(157), 1324.CrossRefGoogle Scholar
Maï, C., Perez, J., Tatibouët, J. and Vassoille, R.. 1978. Vitesse des dislocations dans la glace dopée avec HF. J. Phys. [Paris] Lett., 39(17), 307310.Google Scholar
Nakamura, T. and Jones, S.J.. 1970. Softening effect of dissolved hydrogen chloride in ice crystals. Scripta Metall., 4(2), 123126.Google Scholar
Nakamura, T. and Jones, S.J.. 1973. Mechanical properties of impure ice crystals. In Whalley, E., Jones, S.J. and Gold, L.W., eds. Physics and chemistry of ice. Ottawa, Ont., Royal Society of Canada, 365369.Google Scholar
Oguro, M. 1988. Dislocations in artificially grown single crystals of ice. In Higashi, A., ed. Lattice defects in ice crystals: X-ray topographic observations. Sapporo, Hokkaido University Press, 2747.Google Scholar
Shearwood, C. and Whitworth, R.W.. 1992. The velocity of dislocations in crystals of HCl-doped ice. Philos. Mag. A, 65(1), 8589.Google Scholar
Trickett, Y.L., Baker, I. and Pradhan, P.M.S.. 2000. The effects of sulfuric acid on the mechanical properties of ice single crystals. J. Glaciol., 46(153), 239243.Google Scholar
Figure 0

Fig. 1. The dimensions and orientation of the ice single crystals. The plane with a hexagon indicates the orientation of the basal plane, which was tilted to either θ = 45° or θ = 3° from the top surface.

Figure 1

Fig. 2. Typical RSS–shear-strain curves at various axial strain rates (shown in s−1) for high-purity ice single crystals with the c axis at 45° to the loading direction at −10°C (a); for ice single crystals doped with 3.2 ppm H2SO4 with the c axis at 45° to the loading direction at −10°C (b); for high-purity ice single crystals with the c axis at 45° to the loading direction at −30°C (c); and for ice single crystals doped with 3.2 ppm H2SO4 with the c axis at 45° to the loading direction at −30°C (d).

Figure 2

Fig. 3. Graph on log–log scales, of shear strain rate versus peak stress, showing a comparison between the n values (slopes) of undoped and H2SO4-doped ice single crystals at different temperatures. The data at −20°C are from Trickett and others (2000) and are for 3.4 ppm H2SO4 (not 6.8 ppm as noted in that publication).

Figure 3

Fig. 4. RSS–shear-strain curves for high-purity and 3.2 ppm H2SO4-doped ice single crystals with θ = 45° at an axial strain rate of 1 × 10−5 s−1 at −30°C.

Figure 4

Fig. 5. Comparison between the RSS–shear-strain curves for high-purity ice single crystals and ice single crystals doped with various concentrations of H2SO4. The basal plane orientation is θ = 3°; axial strain rate = 1 × 10−5 s−1; temperature = −10°C. The curves are offset along the strain axis.

Figure 5

Fig. 6. Comparison of the reduction in peak RSS difference, Δσ, versus C1/2 in ice single crystals compressed at −10°C and −20°C normalized to a shear strain rate of 1 × 10−5 s−1. The data at −20°C are from Trickett and others (2000).