Hostname: page-component-8448b6f56d-sxzjt Total loading time: 0 Render date: 2024-04-19T05:11:38.411Z Has data issue: false hasContentIssue false
  • English
  • Français

Stress evolution in a Ti/Al(Si,Cu) dual layer during annealing

Published online by Cambridge University Press:  18 March 2011

Ola Bostrom ,
Patrice Gergaud ,
Olivier Thomas  and
Philippe Boivin
Ola Bostrom
Affiliation:
Laboratoire TECSEN, UMR CNRS 6122, Université d'Aix-Marseille III 13397 Marseille Cedex 20 STMicroelectronics 6”, Rousset, France
Patrice Gergaud
Affiliation:
Laboratoire TECSEN, UMR CNRS 6122, Université d'Aix-Marseille III 13397 Marseille Cedex 20
Olivier Thomas
Affiliation:
Laboratoire TECSEN, UMR CNRS 6122, Université d'Aix-Marseille III 13397 Marseille Cedex 20
Philippe Boivin
Affiliation:
STMicroelectronics 6”, Rousset, France
Get access

Abstract

Mechanical stress and stress evolution in interconnections may cause reliability problems in IC circuits. It is thus of great importance to understand the origin of this stress.

In this paper, the stress evolution during the solid state reaction between blanket titanium and aluminum films has been studied by in-situ substrate curvature measurements. Whereas the formation of TiAl3 is expected to induce large tensile stress because of a global volume decrease of 6-8%, curvature measurements of titanium/aluminum dual layers during annealing at 450°C suggests the formation of a compressive compound.

The evolution of the average force per unit width of the layer during the solid state reaction is interpreted on the basis of a phenomenological model used to describe stress evolution during silicide formation.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 673: Symposium P – Dislocations and Deformation Mechanisms in Thin Films and Small Structures , 2001 , P1.5
Copyright
Copyright © Materials Research Society 2001

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1]Gardner, D.S. and Flinn, P.A., IEEE Trans. Electron. Dev. 35, 2160 (1988)Google Scholar
[2]Nix, W.D., Metallurgical Transactions, 20A, 2217 (1989)Google Scholar
[3]Thouless, M.D, Gupta, J. and Harper, J.M.E., J.Mater.Res, 8, 1845 (1993)Google Scholar
[4]Arzt, E., Acta Mater., 46, 5611 (1998)Google Scholar
[5]Hansen, M., Constitution of binary alloys, McGraw-Hill (1958)Google Scholar
[6]Wohlert, S. and Bormann, R., J. Appl. Phys., 85, 825 (1999)Google Scholar
[7]Gardner, D.S. and Flinn, P.A., J. Appl. Phys, 67, 1831 (1990)Google Scholar
[8]d'Heurle, F.M. and Thomas, O., Defect and Diffusion Forum, 129–130, 137 (1996)Google Scholar
[9]Flinn, P.A., Gardner, D.S. and Nix, W.D., IEEE Trans. Electron. Dev. ED–34, 689 (1987)Google Scholar
[10]Stoney, G.G., Proc. Royal Soc. London Ser. A 82 (1909) 172 Google Scholar
[11]Zhang, S.L. and d'Heurle, F.M., Thin Solid Films, 213, 34 (1992)Google Scholar
[12]Colgan, E.G., Materials Science Reports, 5 1 (1990)Google Scholar