Hostname: page-component-7479d7b7d-pfhbr Total loading time: 0 Render date: 2024-07-08T07:50:07.288Z Has data issue: false hasContentIssue false
  • English
  • Français

Critical Issues In Measuring The Mechanical Properties Of Hard Films On Soft Substrates By Nanoindentation Techniques

Published online by Cambridge University Press:  10 February 2011

Jack C. Hay  and
G. M. Pharr
Jack C. Hay
Affiliation:
Oak Ridge National Laboratory, P.O. Box 2008, M.S. 6118, Oak Ridge, TN 37831
G. M. Pharr
Affiliation:
Department of Materials Science, Rice University, 6100 Main St., Houston, TX, 77005
Get access

Abstract

This study explores the difficulties encountered when using conventional nanoindentation techniques to measure the Young's modulus and hardness of hard films on soft substrates. In general, the indentation measurement of film/substrate systems is affected by four material properties: the Young's modulus and hardness of the film, and the Young's modulus and hardness of the substrate. For the particular case of a hard film on a soft substrate, there is a tendency for the material around the hardness impression to sink-in which results from the large difference in yielding of the two materials. In this study, a ‘model’ system consisting of NiP on annealed Cu was used to explore the behavior. This system is interesting because the film and substrate have similar Young's moduli, minimizing the elastic behavior as a variable. In contrast, the hardness of NiP is approximately 7–18 GPa, and that of the annealed copper is less than 1 GPa, providing a factor of 10 difference in the plastic flow characteristics. Experimental results indicate that standard analytical methods for determining the contact depth, hardness and Young's modulus do not work well for the case of a hard film on a soft substrate. At shallow contact depths, the measured indentation modulus is close to that of the film, but at larger depths sink-in phenomena result in an overestimation of the contact area, and an indentation modulus which is less than the Young's modulus of both the film and substrate. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) provide critical details of the physical processes involved, and illustrate how the standard data analyses overestimate the true contact area.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 505 , 1997 , 65
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Pethica, J. B., Hutchings, R., Oliver, W. C., Phil. Mag. A, 48, 593–606 (1983).Google Scholar
2.Doerner, M. F., Nix, W. D., J. Mater. Res., 1, 601 (1986).Google Scholar
3.Oliver, W. C., Pharr, G. M., J. Mater. Res., 7, 1564–1583 (1992).Google Scholar
4.Hainsworth, S. V., Bartlett, T., Page, T. F., Thin Solid Films, 236, 214–218 (1993).Google Scholar
5.Page, T. F., Hainsworth, S. V., Surface and Coatings Technology, 61, 201–208 (1993).Google Scholar
6.Bhattacharya, A. K., Nix, W. D., Int. J. Solids Structures, 24, 1287–1298 (1988).Google Scholar
7.Burnett, P. J., Rickerby, D. S., Thin Solid Films, 148, 51–65 (1987).Google Scholar
8.Tsui, T. Y., Oliver, W. C., Pharr, G. M., Mat. Res. Soc. Symp. Proc., 436, 207–212 (1997).Google Scholar
9.King, R. B., Int. J. Solids Structures, 23, 1657–1664 (1987).Google Scholar
10.Gao, H., Chiu, C-H, Lee, J., Int. J. Solids Structures, 29, 2471–2492 (1992).Google Scholar
11.Burnett, P. J., Rickerby, D. S., Thin Solid Film, 148, 41–50 (1987).Google Scholar
12.Stone, D. S., J. Electronic Packaging, 112, 41–46 (1990).Google Scholar
13.Sneddon, I. N., Int. J. Engng. Sci., 3, 47–57 (1965).Google Scholar
14.Samuels, L. E., in Microindentation Techniques in Materials Science and Engineering, edited by Blau, P. J. and Lawn, B. R. (ASTM STP 889, ASTM, Philadelphia, 1986), p. 5.Google Scholar
15.Sargent, P. M., in Microindentation Techniques in Materials Science and Engineering, edited by Blau, P. J. and Lawn, B. R. (ASTM STP 889, ASTM, Philadelphia, 1986), p. 160.Google Scholar
16.Hertzberg, R. W., Deformation and Fracture Mechanics of Engineering Materials, (John Wiley & Sons, New York, 1989), p. 7.Google Scholar