Hostname: page-component-7c8c6479df-p566r Total loading time: 0 Render date: 2024-03-29T15:04:43.370Z Has data issue: false hasContentIssue false

A Comparison of Thermal, Line-Source Electron Beam and CW Laser Annealing for the Fabrication of Ersi2 Schottky Barrier on Si.

Published online by Cambridge University Press:  22 February 2011

C. S. Wu
Affiliation:
University of California at San Diego, La Jolla, CA 92093
D.M. Scott
Affiliation:
University of California at San Diego, La Jolla, CA 92093
S. S lau
Affiliation:
University of California at San Diego, La Jolla, CA 92093
A. Wakita
Affiliation:
Stanford Electronics Laboratories, Stanford, CA 94305
T. W. Sigmon
Affiliation:
University of California at San Diego, La Jolla, CA 92093
J. A. Knapp
Affiliation:
Sandia National Laboratories, Albuquerque, NM 87185
S. T. Picraux
Affiliation:
University of California at San Diego, La Jolla, CA 92093
Get access

Abstract

ErSi2 contacts formed by reacting Er with single crystal silicon using conventional furnace heat treatment are dominated by pits. Recently rapid electron and laser beam heating have been used to form pit-free ErSi 2 layers on Si by reacting Er with the Si substrate. For this investigation we studied the electrical properties of erbium silicide/Si<p,100> contact prepared by thermal, laser and electron beam annealing. We prepared and annealed three types of samples; (I) Er(600Å)/Si<p,100>, (II) Si(100Å)/ Er(600Å)/Si<p,100> and (III) Si(900Å)/Er(600Å)/Si<p,100>.The barrier height of the pit-free thermal annealed samples (type III) was ∼0.78 eV. All laser and e-beam annealed samples were observed to be pit-free. The barrier heights for the laser annealed samples varied from ∼ 0.63 eV for type I samples to ∼ 0.77 eV for type III samples. The e-beam annealed samples gave barrier heights ∼ 0.71 eV (type I and II) and ∼ 0.77 eV for type III. The barrier heights of beam processed diodes shifted towards the 0.78 eV range upon post-annealing. We model these results in terms of defects created at the ErSi2-Si interface.

Type
Research Article
Copyright
Copyright © Materials Research Society 1984

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Tu, K.N., Thompson, R.D. and Tsaur, B.Y., Appl. Phys. Lett. 38, 626 (1981).CrossRefGoogle Scholar
2. Norde, H., de Sousa Pires, J., d'Heurle, F., Pesavento, F., Petersson, S. and Tove, P.A., Appl. Phys. Lett. 38, 865 (1981).CrossRefGoogle Scholar
3. Thompson, R.D., Tsaur, B.Y. and Tu, K.N., Appl. Phys. Lett. 38, 535 (1981).CrossRefGoogle Scholar
4. Wu, C.S., Lau, S. S., Kuech, T.F. and Liu, B.X., Thin Solid Films, 104, 175 (1983).CrossRefGoogle Scholar
5. Lau, S.S., Pai, C.S., Wu, C.S., Kuech, T.F. and Liu, B.X., Appl. Phys. Lett. 41, 77 (1982).CrossRefGoogle Scholar
6. Knapp, J.A., Picraux, S.T., Wu, C.S. and Lau, S.S., submitted to Appl. Phys. Lett.Google Scholar
7. Wakita, A. and Sigmon, T.W., private communication.Google Scholar
8. Kern, W., Puotinen, D.A., RCA Review, June 1970, p.187.Google Scholar
9. Knapp, J.A. and Picraux, S.T., J. Appl. Phys. 53, 1492 (1982).CrossRefGoogle Scholar
10. Knapp, J.A. and Picraux, S.T., in Laser-Solid Interactions and Transient Thermal Processing of Materials, Narayan, J., Brown, W.L. and Lemon, R.A., eds., (Elsevier North Holland, N.Y., 1983), p. 557 Google Scholar
11. von Allmen, M., in Laser and Electron Beam Processing of Materials, White, C.W. and Peercy, P.S., eds., (Academic Press, N.Y., 1980), p.6.CrossRefGoogle Scholar
12. Mullins, F. and Brunnschweiler, A., Solid State Electronics, 19, 47 (1976).CrossRefGoogle Scholar