Hostname: page-component-8448b6f56d-dnltx Total loading time: 0 Render date: 2024-04-19T22:51:03.226Z Has data issue: false hasContentIssue false
  • English
  • Français

Cladding Evaluation in the Yucca Mountain Repository Performance Assessment

Published online by Cambridge University Press:  10 February 2011

Eric R. Siegmann ,
J. Kevin McCoy  and
Robert Howard
Eric R. Siegmann
Affiliation:
Duke Engineering and Services, eric_siegmann@ymp.gov(all) 1211 Town Center Drive, Las Vegas, NV 89144
J. Kevin McCoy
Affiliation:
Framatome Technologies(all) 1211 Town Center Drive, Las Vegas, NV 89144
Robert Howard
Affiliation:
TRW Environmental Safety Systems, (all) 1211 Town Center Drive, Las Vegas, NV 89144
Get access

Abstract

The Yucca Mountain Project (YMP) 1998 Total System Performance Assessment Viability Assessment (TSPA-VA) analyzed the degradation of Zircaloy clad commercial fuel rods and the resulting exposure of the fuel in the event of a waste package failure. The cladding degradation mechanisms considered were damage before emplacement, mechanical failure from drift collapse, localized corrosion, general corrosion, delayed hydride cracking (DHC), hydride reorientation, creep rupture, and stress corrosion cracking (SCC). The potential for further cladding degradation due to cladding rupture as a result of fuel oxidation was also considered in the modeling effort. These models have been improved for use in future TSPAs.

The current cladding degradation model divides the analysis into two phases, cladding failure (perforation) and cladding unzipping (crack propagation caused by the expansion of UO2 fuel after reaction with water). Cladding failure occurs during reactor operation, from creep strain failure during high temperature periods in dry storage or in the early periods in the repository, or localized corrosion. After a Waste Package (WP) containing spent nuclear fuel in the repository fails, moisture is assumed to enter the waste package and the failed cladding starts to unzip (tear open) from the formation of secondary uranium phases. This slowly exposes the fuel. In addition, the inventory of fission products located in the gap between the cladding and fuel pellet is rapidly released. The cladding model limits the amount of fuel that is exposed to moisture and becomes available for dissolution. As a result, the doses to the affected population are reduced (factor of 20 to 50 in TSPA-VA) from the case where cladding is not considered.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 608: Symposium QQ – Scientific Basis for Nuclear Waste Management XXIII , 1999 , 3
Copyright
Copyright © Materials Research Society 2000

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1 Ahn, T.M., Cragnolino, G.A., Chan, K.S., and Sridhar, N., Scientific Bases for Cladding Credit in the High-Level Waste Management at the Proposed Yucca Mountain Repository, in Scientific Basis for Nuclear Waste Management XXII, edited by J. Lee and D. Wronkiewicz, (Mater. Res. Soc. Proc. 556, Warrendale, PA 15086-7576, 1999).Google Scholar
2 Cohen, S. & Associates, Effectiveness of Fuel Rod Cladding as an Engineered Barrier in the Yucca Mountain Repository, S. Cohen & Associates, McLean, Virginia, 1999.Google Scholar
3 Henningson, P.J., Cladding Integrity Under Long Term Disposal, Doc. ID: 51-1267509-00, Framatome Technologies, Lynchburg, VA, 1998.Google Scholar
4 Cunningham, M.E., Simonen, E.P., Allemann, R.T., Levy, I.S., and Hazelton, R.F., Control of Degradation of Spent LWR Fuel During Dry Storage in an Inert Atmosphere, PNL-6364, Pacific Northwest Laboratory, Richland, Washington 1987.Google Scholar
5 Peehs, M., Assessment of Dry Storage Performance of Spent LWR Fuel Assemblies with Increasing Burn-Up. Erlangen, Germany: Siemens KWU-NBT. Co-ordinated Research Program (CRP) on Spent Fuel Performance Assessment and Research (SPAR), First RCM held in Washington DC-USA, April 20-24, 1998.Google Scholar
6 Wilson, C.N., Results from Cycles 1 and 2 of NNWSI Series 2 Spent Fuel Dissolution Tests, HEDL-TME-85-22, Richland, Washington: Westinghouse Hanford Company, 1987.Google Scholar
7 Wilson, C.N., Results from NNWSI Series 3 Spent Fuel Dissolution Tests, PNL-7170, Richland, Washington: Pacific Northwest Laboratory, 1990.Google Scholar
8 Sanders, T.L., Seager, K.D., Rashid, Y.R., Barrett, P.R., Malinauskas, A.P., Einziger, R.E., Jordan, H., Duffey, T.A., Sutherland, S.H., and Reardon, P.C., A Method for Determining the Spent-Fuel Contribution to Transport Cask Containment Requirements, SAND90-2406, Albuquerque, New Mexico: Sandia National Laboratories, 1992.Google Scholar
9 Hillner, E.; Franklin, D.G.,; and Smee, J.D.,. The Corrosion of Zircaloy-Clad Fuel Assemblies in a Geologic Repository Environment. WAPD-T-3173, West Mifflin, Pennsylvania: Bettis Atomic Power Laboratory. 1998 Google Scholar
10 Matsuo, Y., “Thermal Creep of Zircaloy-4 Cladding Under Internal Pressure.” Journal of Nuclear Science and Technology, 24 (2), 111–119. Tokyo, Japan: Atomic Energy Society of Japan, 1987.Google Scholar
11 Chung, H.M., Yaggee, F.L., and Kassner, T.F., “Fracture Behavior and Microstructural Characteristics of Irradiated Zircaloy Cladding.” Special Technical Publication, 0 (939) 775. Philadelphia, Pennsylvania: American Society for Testing and Materials, 1987.Google Scholar