Hostname: page-component-848d4c4894-tn8tq Total loading time: 0 Render date: 2024-06-27T08:56:31.936Z Has data issue: false hasContentIssue false
  • English
  • Français

Auger Sputter Depth Profiling Applied to Advanced Semiconductor Device Structures

Published online by Cambridge University Press:  22 February 2011

D. K. Skinner ,
C. Hill  and
M. W. Jones
D. K. Skinner
Affiliation:
Plessey Research (Caswell) Limited, Allen Clark Research Centre, Caswell, Towcester, Northants NN12 8EQ, England
C. Hill
Affiliation:
Plessey Research (Caswell) Limited, Allen Clark Research Centre, Caswell, Towcester, Northants NN12 8EQ, England
M. W. Jones
Affiliation:
Plessey Research (Caswell) Limited, Allen Clark Research Centre, Caswell, Towcester, Northants NN12 8EQ, England
Get access

Abstract

The continuing miniaturisation of modern semiconductor devices is placing new demands on the spatial resolution of many existing assessment techniques. With device structures reduced to nm dimensions the need to optimise conditions for high resolution in-depth profiling is essential for accurate characterisation. In this paper we present Auger profiles of two micro-electronic structures and consider the choice of ion beam parameters necessary to minimise ion beam induced distortion. In VLSI (Very Large Scale Integration) technology where high dopant concentrations are ion implanted into shallow layer structures, Auger profiling can be used to establish dopant distributions accurately in the peak regions of the high dose implant. This information is shown to provide data for process modelling programmes.

Also presented are profiles of MOCVD (Metal Organic Chemical Vapour Deposition) grown GaAlAs/GaAs superlattices with 70 Å repeat structures. Interface width measurements are of particular importance in this case where sharp interfaces are a pre-requisite for good device performance. These structures have been found to be very vulnerable to enhanced atomic mixing, a consequence of the small mass of the Al atom. The Al content of the GaAlAs determining the obtainable in-depth resolution.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 48: Symposium E – Applied Materials Characterization , 1985 , 179
Copyright
Copyright © Materials Research Society 1985

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Hill, C and Butler, A L. Published in Solid State Devices 1983 (Rhoderick, E H ed) Inst of Physics, London (1984).Google Scholar
2. Carter, G, Gras-Marti, A and Nobes, M J. Rad Efects, 62, 119 (1982).Google Scholar
3. Seah, M P and Hunt, C P. Surf-Interface Anal, 5, 33 (1983).Google Scholar
4. Zinner, E. J Electrochem Soc, 130, No.5, 1990 (1983).CrossRefGoogle Scholar
5. Hofmann, S. Surf Interface Anal, 2, 148 (1980).CrossRefGoogle Scholar
6. Wittmaack, K. J Appl Phys, 53 (7) 4817 (1982).Google Scholar
7. Chapman, R E. J Mater Sci, 12, 1125 (1977).CrossRefGoogle Scholar
8. Heyes, D M, Barber, M and Clarke, J H R. Surf Sci, 105, 225 (1981).CrossRefGoogle Scholar
9. Fine, J, Navinsek, B, Davarya, F and Andreadis, T D. J Vac Sci Technol, 20, 449 (1982).Google Scholar
10. Mathieu, H J, McClure, D E and Landolt, D. Thin SOlid Films, 38, 281 (1976).CrossRefGoogle Scholar