Hostname: page-component-8448b6f56d-qsmjn Total loading time: 0 Render date: 2024-04-25T06:13:22.977Z Has data issue: false hasContentIssue false
  • English
  • Français

Alloying Effect on the Microstructure and Property of Single Crystal Ni3Al Alloys

Published online by Cambridge University Press:  26 February 2011

Zhang Jishan ,
Zhang Zhiya ,
Tang Yajun ,
Zhang Jinghua ,
Yu Yang ,
Li Yingao ,
Ding Dongsheng  and
Hu Zhuangqi
Zhang Jishan
Affiliation:
Institute of Metal Research, Academia Sinica, 2-6 Wenhua Rd., Shenyang, P.R.China
Zhang Zhiya
Affiliation:
Institute of Metal Research, Academia Sinica, 2-6 Wenhua Rd., Shenyang, P.R.China
Tang Yajun
Affiliation:
Institute of Metal Research, Academia Sinica, 2-6 Wenhua Rd., Shenyang, P.R.China
Zhang Jinghua
Affiliation:
Institute of Metal Research, Academia Sinica, 2-6 Wenhua Rd., Shenyang, P.R.China
Yu Yang
Affiliation:
Institute of Metal Research, Academia Sinica, 2-6 Wenhua Rd., Shenyang, P.R.China
Li Yingao
Affiliation:
Institute of Metal Research, Academia Sinica, 2-6 Wenhua Rd., Shenyang, P.R.China
Ding Dongsheng
Affiliation:
Institute of Metal Research, Academia Sinica, 2-6 Wenhua Rd., Shenyang, P.R.China
Hu Zhuangqi
Affiliation:
Institute of Metal Research, Academia Sinica, 2-6 Wenhua Rd., Shenyang, P.R.China
Get access

Abstract

The alloying effects of Cr, Zr, Ta, Nb and B on the microstructure and properties of single crystal Ni3Al alloys have been studied. The strength of the alloys has been improved markedly with promising plasticity. The 0.2% yield stress of some of these alloys is higher than that of IN713C, a typical cast nickel-base superalloy, in the temperature range from 25 to 950°C and some of them reach the strength level of advanced cast nickel-base alloys such as IN100 in the high temperature range. The creep strength of these alloys is also improved markedly. The single crystal Ni3Al alloy with a high Cr content ( 7 at-%) obviously shows an intermediate temperature low plasticity behavior. Although heat treatment can only slightly improve the strength, it can double the elongation of the alloy from 25% to 50%. In the Ni3Al monocrystal containing 1.2at%Zr there exist great amounts of the low melting point Ni5 Zr-γ eutectics around the ordinary γ/γ′ eutectics. This makes it difficult to homogenize the coarse casting structures completely.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 133: Symposium H – High-Temperature Ordered Intermetallic Alloys III , 1988 , 549
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. High temperature Ordered Intermetallic Alloys, edited by Koch, C.C., Liu, C.T., and Stoloff, N.S. (Mater. Res. Soc. Proc. 39, Boston, MA 1984).Google Scholar
2. High Temperature Ordered Intermetallic Alloys II, edited by Stoloff, N.S. et al (Mater. Res. Soc. Proc. 81, Boston MA 1986).Google Scholar
3. Yamagata, T., Harada, H., Nakazawa, S., Yamazaki, M., and Nakagawa, Y.G., in Superalloys 1984, edited by Gell, M., Kortovich, C.S., Bricknell, R.H., Kent, W.B., and Radavich, J.F. (The Metallurgical Society, Warrendale, PA 1984). pp.157–166.Google Scholar
4. Dalal, R.P., Thomas, C.R., and Dardi, L.E., in Superalloys 1984, edited by Gell, M., Kortovich, C.S., Bricknell, R.H., Kent, W.B., and Radavich, J.F. (The Metallurgical Society, Warrendale, PA 1984), pp.185–197.Google Scholar
5. Mishima, Y. et al, Trans. Jpn. Inst. Metals 27, 41(1986).CrossRefGoogle Scholar
6. Umakoshi, Y., Pope, D.P., and Titek, V., Acta Metall. 32, 449(1984).CrossRefGoogle Scholar
7. Heredia, F. et al, in High Temperature Ordered Intermetallic Alloys II. edited by Stoloff, N.S. et al (Mater. Res. Soc. Proc. 81, Boston, MA 1986) pp. 213.Google Scholar
8. Bonda, N.R., Pope, D.P., and Laird, C., Acts Metal. 35, 2385(1987).Google Scholar
9. Lall, C., Chin, S., and Pope, P., Metall. Trans. A, 10A, 1323(1979).Google Scholar
10. Liu, C.T., White, C.L., and Horton, J.A., Acta Metall. 33, 213(1985).Google Scholar
11. Huang, S.C., Taub, A.I., and Chang, K.M., Acta Metall. 32, 1703(1984).CrossRefGoogle Scholar
12. Flinn, P.A., Trans. AIME, 218, 145(1960).Google Scholar
13. Thornton, P.H., Davles, R.G., and Johnston, T.L., Metall. Trans. 1, 207(1970).Google Scholar
14. Hsu, S.E. et al, in High Temperature Ordered Intermetallic Alloys II, edited by Stoloff, N.S. et al (Mater. Res. Soc. Proc. 81 Boston, MA 1986), pp.507.Google Scholar
15. Liu, C.T., White, C.T., and Lee, E.H., Scr. Metall. 19, 1247(1985).CrossRefGoogle Scholar
16. Mishima, Y., Ochlai, S., Yodogawa, M., and Suzuki, T., Trans. Inst. Met. Jpn. 27, 41(1987).Google Scholar