Hostname: page-component-7bb8b95d7b-lvwk9 Total loading time: 0 Render date: 2024-10-05T14:45:42.430Z Has data issue: false hasContentIssue false

Micromachined Nanoparticulate Ceramic Gas Sensor Array on Mems Substrates

Published online by Cambridge University Press:  15 March 2011

Martin Heule
Affiliation:
Nonmetallic Inorganic Materials, ETH Zurich Sonneggstrasse 5, 8092 Zurich, Switzerland
Ludwig J. Gauckler
Affiliation:
Nonmetallic Inorganic Materials, ETH Zurich Sonneggstrasse 5, 8092 Zurich, Switzerland
Get access

Abstract

In most MEMS applications, dust and particles are avoided with considerable endeavor. However, for many applications such as gas sensors, powders of functional ceramics would often provide better performance than corresponding thin film layers. There are abundant ways to synthesize powders with well defined chemical composition, phase and size distribution, whereas the processing parameters for thin-film preparation often are limited. Specifically where the functionality is based on a chemical reaction on surfaces, nanoscaled powders with a high specific surface area have proven useful. This is the case for tin oxide gas sensors that exhibit a drop in electrical resistivity induced by the combustion of the analyte gas. Soft lithography was used for the fabrication of mesoscaled powder-based ceramic structures. In this paper, we present the integration of small tin oxide microstructures with an effective gas-sensing area of 10 by 30 νm2 on a micro-hotplate substrate. Such a substrate can heat the ceramic sensor to operating temperatures quickly with low power consumption. A whole array of sensors can be integrated on one micro-hotplate. Processing steps to prepare the sensor array on the micro hot plate are presented and discussed concerning processing sequence, sensitivity towards 1000 to 1500 ppm hydrogen and power consumption. Additionally, effects of grain growth due to on-chip annealing of the ceramic nanostructure were observed.

Type
Research Article
Copyright
Copyright © Materials Research Society 2002

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1 Suehle, J. S., Cavicchi, R. E., Gaitan, M., and Semancik, S., IEEE Electron Device Letters 14 (3), 118 (1993).Google Scholar
2 Semancik, S., Cavicchi, R. E., Wheeler, M. C., Tiffany, J. E., Poirier, G. E., Walton, R. M., Suehle, J. S., Panchapakesan, B., and DeVoe, D. L., Sens. Actuator B-Chem. 77 (1-2), 579 (2001).Google Scholar
3 Faglia, G., Comini, E., Cristalli, A., Sberveglieri, G., and Dori, L., Sensors and Actuators B 55, 140 (1999).Google Scholar
4 Barsan, N., Schweizer-Berberich, M., and Gäpel, W., Fresenius J. Anal. Chem. 365, 287 (1999).Google Scholar
5 Xia, Y. and Whitesides, G. M., Angew. Chem. Int. Ed. 37, 550 (1998).Google Scholar
6 Briand, D., Krauss, A., Schoot, B. van der, Weimar, U., Barsan, N., Gopel, W., and Rooij, N. F. de, Sens. Actuator B-Chem. 68 (1-3), 223 (2000).Google Scholar
7 Briand, D., Schoot, B. van der, Rooij, N. F. de, Sundgren, H., and Lundsträm, I., IEEE J. MEMS 9 (3), 303 (2000).Google Scholar
8 Carotta, M. C., Ferroni, M., Gnani, D., Guidi, V., Merli, M., Martinelli, G., Casale, M. C., and Notaro, M., Sensors and Actuators B 58 (01. Mrz), 310 (1999).Google Scholar
9 Vacassy, R., Houriet, R., Plummer, G. J. G., Dutta, J., and Hofmann, H., Tin Dioxide Nanopowders for Gas Sensor Applications. (MRS Res. Soc. Proc., 501, Warrendale PA, 1998).Google Scholar