Hostname: page-component-76fb5796d-r6qrq Total loading time: 0 Render date: 2024-04-25T07:11:10.095Z Has data issue: false hasContentIssue false
  • English
  • Français

Rapid Electrical Heating of Aluminum-Boron Nano-Laminates

Published online by Cambridge University Press:  22 January 2018

David M. Lunking ,
David P. Adams  and
Christopher J. Morris
David M. Lunking
Affiliation:
General Technical Services LLC, Adelphi, MD Micro/Nano Materials and Devices Branch, U.S. Army Research Laboratory, Adelphi, MD
David P. Adams
Affiliation:
Sandia National Laboratories, Albuquerque, NM
Christopher J. Morris*
Affiliation:
Micro/Nano Materials and Devices Branch, U.S. Army Research Laboratory, Adelphi, MD
*
*(Email: christopher.j.morris58.civ@mail.mil)
Get access

Abstract

Rapid or explosive heating of electrically conductive films has several applications, and the use of reactive laminates to increase output energy is an intriguing concept. Past studies have shown electrically heated aluminum/nickel (Al/Ni) nano-laminate films to augment this energy by an amount approximately equivalent to the expected heat of mixing between the two elements, which for most intermetallics is a significant fraction of the total heat of reaction (86% for Al/Ni). In this study, we investigate the use of sputtered aluminum/boron (Al/B) laminates to determine whether a similar increase, as measured by the velocity of an ejected flyer layer, occurs. However, observed velocities in any samples containing boron were 38% to 45% lower than samples without boron, despite much higher heats of reaction reported in the literature for Al/B. We attributed this reduction to the vaporization temperature of boron being much higher than that of Al, and because Al electrical resistivity at elevated temperatures was still much lower than boron, boron heating was less efficient as vaporized Al expanded and drove the ejected flyer. These results and analysis give insight into other reactive material combinations in which one of the constituents is an electrical insulator.

Keywords

BAlsputtering
Type
Articles
Information
MRS Advances , Volume 3 , Issue 17: Processing and Manufacturing , 2018 , pp. 905 - 910
Check for updates
Copyright
Copyright © Materials Research Society 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Morris, C. J., Wilkins, P., and May, C., J. Appl. Phys. 113 (2013) 043304 (7 pp).CrossRefGoogle Scholar
Morris, C. J., Mary, B., Zakar, E., Barron, S., Fritz, G., Knio, O., Weihs, T. P., Hodgin, R., Wilkins, P., and May, C., J. Phys. Chem. Solids 71 (2010) 84.CrossRefGoogle Scholar
Morris, C. J., Wilkins, P., May, C., Zakar, E., and Weihs, T. P., Thin Solid Films 520 (2011) 1645.CrossRefGoogle Scholar
Burden, R., Gray, J., and Oxley, C., IEEE Trans. Magn. 25 (1989) 107.CrossRefGoogle Scholar
Rosen, M. D., Hagelstein, P. L., Matthews, D. L., Campbell, E. M., Hazi, A. U., Whitten, B. L., MacGowan, B., Turner, R. E., Lee, R. W., Charatis, G., Busch, G. E., Shepard, C. L., and Rockett, P. D., Phys. Rev. Lett. 54 (1985) 106.CrossRefGoogle Scholar
Stewardson, H., Novac, B., Smith, I., and Senior, P., in Proc. 10th International Pulsed Power Conference (1995), volume 2, pp. 1121 –1125.Google Scholar
Takaki, K., Takada, Y., Itagaki, M., Mukaigawa, S., Fujiwara, T., Ohshima, S., Takahashi, I., and Kuwashima, T., in Proc. 14th International Pulsed Power Conference (2003), volume 2, pp. 1258 –1261.Google Scholar
Sandakov, V. M., Esin, Y. O., and Gel’d, P. V., Russ. J. Phys. Chem. 1020 (1971) 45.Google Scholar
Fischer, S. H. and Grubelich, M. C., in Proc. 24th Int. Pyrotechnics Seminar (Monterey, CA, 1998), pp. 1–4.Google Scholar
Strand, O. T., Goosman, D. R., Martinez, C., Whitworth, T. L., and Kuhlow, W. W., Rev. Sci. Instrum. 77 (2006) 083108.CrossRefGoogle Scholar
Greiner, E. S. and Gutowski, J. A., J. Appl. Phys. 28 (1957) 1364.CrossRefGoogle Scholar
Desai, P. D., James, H. M., and Ho, C. Y., J. Phys. Chem. Ref. Data 13 (1984) 1131.CrossRefGoogle Scholar