Hostname: page-component-cd9895bd7-7cvxr Total loading time: 0 Render date: 2024-12-22T05:28:03.673Z Has data issue: false hasContentIssue false
  • English
  • Français

Evaluating Deformation-Induced Grain Orientation Change in a Polycrystal During In Situ Tensile Deformation using EBSD

Published online by Cambridge University Press:  20 July 2015

Thomas E. Buchheit ,
Jay D. Carroll ,
Blythe G. Clark  and
Brad L. Boyce
Thomas E. Buchheit*
Affiliation:
Sandia National Laboratories, Materials and Process Science Center, P.O. Box 5800, Albuquerque, NM 87185, USA
Jay D. Carroll
Affiliation:
Sandia National Laboratories, Materials and Process Science Center, P.O. Box 5800, Albuquerque, NM 87185, USA
Blythe G. Clark
Affiliation:
Sandia National Laboratories, Physical, Chemical and Nano Sciences Center, P.O. Box 5800, Albuquerque, NM 87185, USA
Brad L. Boyce
Affiliation:
Sandia National Laboratories, Materials and Process Science Center, P.O. Box 5800, Albuquerque, NM 87185, USA
*
*Corresponding author.tebuchh@sandia.gov
Get access

Abstract

Using an in situ load frame within a scanning electron microscope, a microstructural section on the surface of an annealed tantalum (Ta) polycrystalline specimen was mapped at successive tensile strain intervals, up to ~20% strain, using electron backscatter diffraction. A grain identification and correlation technique was developed for characterizing the evolving microstructure during loading. Presenting the correlated results builds on the reference orientation deviation (ROD) map concept where individual orientation measurements within a grain are compared with a reference orientation associated with that grain. In this case, individual orientation measurements in a deformed grain are measured relative to a reference orientation derived from the undeformed (initial) configuration rather than the current deformed configuration as has been done for previous ROD schemes. Using this technique helps reveal the evolution of crystallographic orientation gradients and development of deformation-induced substructure within grains. Although overall crystallographic texture evolved slowly during deformation, orientation spread within grains developed quickly. In some locations, misorientation relative to the original orientation of a grain exceeded 20° by 15% strain. The largest orientation changes often appeared near grain boundaries suggesting that these regions were preferred locations for the initial development of subgrains.

Keywords

electron backscatter diffraction (EBSD)grain orientationmisorientationmicrostructureplastic deformation
Type
Materials Applications and Techniques
Information
Microscopy and Microanalysis , Volume 21 , Issue 4 , August 2015 , pp. 969 - 984
Copyright
© Microscopy Society of America 2015 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Brewer, L.N., Othon, M.A., Young, L.M. & Angeliu, T.M. (2006). Misorientation mapping for visualization of plastic deformation via electron back-scattered diffraction. Microsc Microanal 12, 85–91.CrossRefGoogle ScholarPubMed
Britton, T.B., Liang, H., Dunne, F.P.E. & Wilkinson, A.J. (2010). The effect of crystal orientation on the indentation response of commercially pure titanium: experiments and simulations. Proc R Soc A 466, 695–719.CrossRefGoogle Scholar
Buchheit, T.E., Battaile, C.C., Weinberger, C.R. & Holm, E.A. (2011). Multi-scale modeling of low temperature deformation in b.c.c. metals. JOM 63(11), 33–36.CrossRefGoogle Scholar
Buchheit, T.E., Wellman, G.W. & Battaile, C.C. (2005). Investigating the limits of polycrystal plasticity modeling. Int J Plasticity 21, 221–249.CrossRefGoogle Scholar
Carroll, J.D., Clark, B.G., Buchheit, T.E., Michael, J.R. & Boyce, B.L. (2013). An experimental analysis of stress projection factors in BCC tantalum. Mater Sci Eng A 581, 108–118.CrossRefGoogle Scholar
Chen, D., Kuo, J.C. & Wu, W.T. (2011). Effect of microscopic parameters on EBSD spatial resolution. Ultramicroscopy 111, 1488–1494.Google Scholar
Delaire, F., Raphanel, J.L. & Rey, C. (2000). Plastic heterogeneities of a copper multicrystal deformed in uniaxial tension: Experimental study and finite element simulations. Acta Mater 48, 1075–1087.CrossRefGoogle Scholar
Engler, O. & Randle, V. (2010). Introduction to Texture Analysis: Macrotexture, Microtexture and Orientation Mapping. Boca Raton, Florida: CRC Press Taylor and Francis Group.Google Scholar
Field, D.P., Merriman, C.C., Allain-Bonasso, N. & Wagner, F. (2012). Quantification of dislocation structure heterogeneity in deformed polycrystals by EBSD. Model Simul Mat Sci Eng 20, 024007.Google Scholar
Field, D.P., Yanke, J.M., McGowan, E.V. & Michaluk, C.A. (2005). Microstructural development in asymmetric processing of tantalum plate. J Electron Mater 34, 1521–1525.CrossRefGoogle Scholar
Gardner, C.J., Adams, B.L., Basinger, J. & Fullwood, D.T. (2010). EBSD-based continuum dislocation microscopy. Int J Plasticity 26, 1234–1247.CrossRefGoogle Scholar
Glez, J.C. & Driver, J. (2001). Orientation distribution analysis in deformed grains. J Appl Cryst 34, 280–288.CrossRefGoogle Scholar
Godfrey, A., Mishin, O.V. & Liu, Q. (2006). Processing and interpretation of EBSD data gathered from plastically deformed metals. Mater Sci Tech 22, 1263–1270.Google Scholar
Haldrup, K., McGinty, R.D. & McDowell, D.L. (2009). Effects of constraints on lattice re-orientation and strain in polycrystal plasticity simulations. Comp Mat Sci 44, 1198–1207.Google Scholar
Hansen, N. & Juul-Jensen, D. (2011). Deformed metals—structure, recrystallization and strength. Mater Sci Tech 27(8), 1229–1240.CrossRefGoogle Scholar
He, W., Ma, W. & Pantleon, W. (2008). Microstructure of individual grains in cold-rolled aluminum from orientation inhomogeneities resolved by electron backscattering diffraction. Mater Sci Eng A 494, 21–27.CrossRefGoogle Scholar
Hughes, D.A., Liu, Q., Chrzan, D.C. & Hansen, N. (1997). Scaling of microstructural parameters: Misorientations of deformation induced boundaries. Acta Mater 45, 105–112.Google Scholar
Humphreys, F.J., Bate, P.S. & Hurley, P.J. (2001). Orientation averaging of electron backscattered diffraction data. J Microsc 201(1), 50–58.Google Scholar
Jiang, J., Britton, T.B. & Wilkinson, A.J. (2013). Measurement of geometrically necessary dislocation density with high resolution electron backscatter diffraction: Effects of detector binning and step size. Ultramicroscopy 125, 1–9.CrossRefGoogle ScholarPubMed
Kalidindi, S.R., Bhattacharyya, A. & Doherty, R.D. (2004). Detailed analyses of grain-scale plastic deformation in columnar polycrystalline aluminium using orientation image mapping and crystal plasticity models. Proc R Soc Lond A 460, 1935–1956.Google Scholar
Kocks, U.F., Tome, C.N. & Wenk, H.R. (1998). Texture and Anisotropy: Preferred Orientations in Polycrystals and their Effect on Materials Properties. Cambridge, UK: Cambridge University Press.Google Scholar
Kysar, J.W., Saito, Y., Oztop, M.S., Lee, D. & Huh, W.T. (2010). Experimental lower bounds on geometrically necessary dislocations density. Int J Plasticity 26, 1097–1123.Google Scholar
Lim, H., Weinberger, C.R., Battaile, C.C. & Buchheit, T.E. (2013). Application of generalized non-Schmid yield law to low temperature plasticity in BCC transition metals. Model Simul Mat Sci 21(4), 045015.Google Scholar
Mika, D.P. & Dawson, P.R. (1999). Polycrystal plasticity modeling of intracrystalline boundary textures. Acta Mater 47, 1355–1369.CrossRefGoogle Scholar
Mishra, S.K., Pant, P., Narasimhan, K., Rollett, A.D. & Samajdar, I. (2009). On the widths of orientation gradient zones adjacent to grain boundaries. Scripta Mater 61, 273–276.Google Scholar
Pantleon, W. (2005). Retrieving orientation correlations in deformation structures from orientation maps. Mater Sci Tech 21(12), 1392–1396.CrossRefGoogle Scholar
Pantleon, W. & Hansen, N. (2001). Dislocation boundaries – The distribution function of disorientation angles. Acta Mater 49, 1479–1493.CrossRefGoogle Scholar
Pedrazas, N.A., Buchheit, T.E., Holm, E.A. & Taleff, E.M. (2014). Dynamic abnormal grain growth in tantalum. Mater Sci Eng A 610, 76–84.Google Scholar
Quey, R., Dawson, P.R. & Driver, J.H. (2012). Grain orientation fragmentation in hot-deformed aluminium: Experiment and simulation. J Mech Phys Solids 60, 509–524.CrossRefGoogle Scholar
Raabe, D., Schlenkert, G., Weisshaupt, H. & Luke, K. (1994). Texture and microstructure of rolled and annealed tantalum. Mater Sci Tech 19, 299–305.CrossRefGoogle Scholar
Rehrl, C., Volker, B., Kleber, S., Antretter, T. & Pippan, R. (2012). Crystal orientation changes: A comparison between a crystal plasticity finite element study and experimental results. Acta Mater 60, 2379–2386.CrossRefGoogle Scholar
Stauffer, D. & Aharony, A. (1994). Introduction to Percolation Theory, 2nd ed. London: Taylor and Francis.Google Scholar
Steinmetz, D.R. & Zaefferer, S. (2010). Toward ultrahigh resolution EBSD by low accelerating voltage. Mater Sci Tech 26(6), 640–645.Google Scholar
Sun, S., Adams, B.L. & King, W.E. (2000). Observations of lattice curvature near the interface of a deformed aluminium bicrystal. Philos Mag A 80, 9–25.Google Scholar
Tatschl, A. & Kolednik, O. (2003). On the experimental characterization of crystal plasticity in polycrystals. Mater Sci and Eng A 342, 152–168.Google Scholar
Weinberger, C.R., Battaile, C.C., Buchheit, T.E. & Holm, E.A. (2012). Incorporating atomistic data of lattice friction into BCC crystal plasticity models. Int J Plasticity 37, 16–30.Google Scholar
Wheeler, J., Cross, A., Drury, M., Hough, R.M., Mariani, E., Piazolo, S. & Prior, D.J. (2011). Time-lapse misorientation maps for the analysis of electron backscatter diffraction data from evolving microstructures. Scripta Mater 65, 600–603.Google Scholar
Wilkinson, A.J. & Britton, T.B. (2012). Strains, planes and EBSD in materials science. Mater Today 15(9), 366–376.Google Scholar
Wright, S.I., Nowell, M.M. & Field, D.P. (2011). A review of strain analysis using electron backscatter diffraction. Microsc Microanal 17, 316–329.CrossRefGoogle ScholarPubMed
Zaafarani, N., Raabe, D., Singh, R.N., Roters, F. & Zaefferer, S. (2006). Three-dimensional investigation of the texture and microstructure below a nanoindent in a Cu single crystal using 3D EBSD and crystal plasticity finite element simulations. Acta Mater 54, 1863–1876.CrossRefGoogle Scholar
Zaefferer, S. (2011). A critical review of orientation microscopy in SEM and TEM. Cryst Res Technol 46(6), 607–628.Google Scholar
Zhao, Z., Ramesh, M., Raabe, D., Cuitino, A.M. & Radovitzky, R. (2008). Investigation of three-dimensional aspects of grain-scale plastic surface deformation of an aluminum oligocrystal. Int J Plasticity 24, 2278–2297.Google Scholar