Hostname: page-component-7c8c6479df-r7xzm Total loading time: 0 Render date: 2024-03-28T23:40:08.076Z Has data issue: false hasContentIssue false

Hybrid coupling layers for bulk metallic glass adhesion

Published online by Cambridge University Press:  19 November 2013

Jeffrey Yang
Affiliation:
Department of Materials Science and Engineering, Stanford University, Stanford, California 94305-2205
Reinhold H. Dauskardt*
Affiliation:
Department of Materials Science and Engineering, Stanford University, Stanford, California 94305-2205
*
a)Address all correspondence to this author. e-mail: dauskardt@stanford.edu
Get access

Abstract

Solutions to the technical challenge of bonding and joining bulk metallic glasses have long been sought after due to the exceptional property sets displayed by this class of engineering materials. Here, we demonstrate the ability to deposit a compositionally and functionally graded hybrid coupling layer using sol–gel processing methods to promote adhesion at the metallic glass–epoxy interface. In this study, we fine-tune the molecular composition by varying the sol Zr:Si ratio, altering film properties that consequently influence crack path selection at the interface. When optimized, up to 3-fold improvements in the adhesive/cohesive properties of these structural bond lines can be attained, with the highest GC values correlating with cohesive cracking through the hybrid. We also demonstrate the ability of these hybrid structures to significantly reduce the influence of moisture-assisted degradation as evidenced by reductions in crack growth rates of over two orders of magnitude and increased threshold limits.

Type
Articles
Copyright
Copyright © Materials Research Society 2013 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Inoue, A.: Stabilization of metallic supercooled liquid and bulk amorphous alloys. Acta Mater. 48, 279 (2000).CrossRefGoogle Scholar
Schuh, C.A., Hufnagel, T.C., and Ramamurty, U.: Mechanical behavior of amorphous alloys. Acta Mater. 55, 4067 (2007).CrossRefGoogle Scholar
Hofmann, D.C., Suh, J., Wiest, A., Duan, G., Lind, M., Demetriou, M.D., and Johnson, W.L.: Designing metallic glass matrix composites with high toughness and tensile ductility. Nature 451, 1085 (2008).CrossRefGoogle ScholarPubMed
Mammeri, F., Le Bourhis, E., Rozes, L., and Sanchez, C.: Mechanical properties of hybrid organic–inorganic materials. J. Mater. Chem. 15, 3787 (2005).CrossRefGoogle Scholar
Sanchez, C., Ribot, F., and Lebeau, B.: Molecular design of hybrid organic–inorganic nanocomposites synthesized via sol-gel chemistry. J. Mater. Chem. 9, 35 (1999).CrossRefGoogle Scholar
Sanchez, C., Julián, B., Belleville, P., and Popall, M.: Applications of hybrid organic–inorganic nanocomposites. J. Mater. Chem. 15, 3559 (2005).CrossRefGoogle Scholar
Liu, J., Chaudhury, M.K., Berry, D.H., Seebergh, J.E., Osborne, J.H., and Blohowiak, K.Y.: Effect of surface morphology on crack growth at a sol-gel reinforced epoxy/aluminum interface. J. Adhes. 82, 487 (2006).CrossRefGoogle Scholar
Liu, J., Chaudhury, M.K., Berry, D.H., Seebergh, J.E., Osborne, J.H., and Blohowiak, K.Y.: Fracture behavior of an epoxy/aluminum interface reinforced by sol-gel coatings. J. Adhes. Sci. Technol. 20, 277 (2006).CrossRefGoogle Scholar
Liu, J., Chaudhury, M.K., Berry, D.H., Seebergh, J.E., Osborne, J.H., and Blohowiak, K.Y.: Effect of processing conditions on adhesion performance of a sol-gel reinforced epoxy/aluminum interface. J. Adhes. Sci. Technol. 22, 1159 (2008).CrossRefGoogle Scholar
Oliver, M.S., Blohowiak, K.Y., and Dauskardt, R.H.: Molecular structure and fracture properties of ZrOX/epoxysilane hybrid films. J. Sol-Gel Sci. Technol. 55, 360 (2010).CrossRefGoogle Scholar
Oliver, M.S. and Dauskardt, R.H.: Mechanical fatigue of hybrid glasses. Small 6, 1892 (2010).CrossRefGoogle ScholarPubMed
Yi, G. and Sayer, M.: An acetic acid/water based sol-gel PZT process I: Modification of Zr and Ti alkoxides with acetic acid. J. Sol-Gel Sci. Technol. 6, 65 (1996).CrossRefGoogle Scholar
Kanninen, M.F.: An augmented double cantilever beam model for studying crack propagation and arrest. Int. J. Fract. 9, 83 (1973).CrossRefGoogle Scholar
Snodgrass, J., Pantelidis, D., Jenkins, M.L., Bravman, J.C., and Dauskardt, R.H.: Subcritical debonding of polymer/silica interfaces under monotonic and cyclic loading. Acta Mater. 50, 2395 (2002).CrossRefGoogle Scholar
Sharratt, B.M., Wang, L.C., and Dauskardt, R.H.: Anomalous debonding behavior of a polymer/inorganic interface. Acta Mater. 55, 3601 (2007).CrossRefGoogle Scholar