Skip to main content Accessibility help
×
Home
Hostname: page-component-99c86f546-qdp55 Total loading time: 0.208 Render date: 2021-12-05T15:13:57.486Z Has data issue: true Feature Flags: { "shouldUseShareProductTool": true, "shouldUseHypothesis": true, "isUnsiloEnabled": true, "metricsAbstractViews": false, "figures": true, "newCiteModal": false, "newCitedByModal": true, "newEcommerce": true, "newUsageEvents": true }

Experiments on drag-reducing surfaces and their optimization with an adjustable geometry

Published online by Cambridge University Press:  10 May 1997

D. W. BECHERT
Affiliation:
DLR, Abteilung Turbulenzforschung, Müller-Breslau-Str. 8, 10623 Berlin, Germany
M. BRUSE
Affiliation:
Hermann-Föttinger-Institut, TU Berlin, Strasse des 17. Juni 135, 10623 Berlin, Germany
W. HAGE
Affiliation:
Hermann-Föttinger-Institut, TU Berlin, Strasse des 17. Juni 135, 10623 Berlin, Germany
J. G. T. VAN DER HOEVEN
Affiliation:
Universitätsklinikum Rudolf Virchow, Klinikum Westend, Labor für Biofluidmechanik, Spandauer Damm 130, 14050 Berlin, Germany
G. HOPPE
Affiliation:
Deutsches Institut für Bautechnik, Kolonnenstr. 30, 10829 Berlin, Germany

Abstract

Previous research has established that surfaces with tiny ribs (riblets) aligned in the streamwise direction can reduce the turbulent wall-shear stress below that of a smooth surface. Typical skin-friction reductions have been found to be about 5%. The results of the present investigation, however, demonstrate a considerable improvement over this value. This improvement is achieved by a systematic experimental optimization which has been guided by theoretical concepts.

A key feature of our experiments is the utilization of an oil channel. Previous experiments in wind tunnels had to contend with very small riblet dimensions which typically had a lateral rib spacing of about 0.5 mm or less. By contrast, in our oil channel, the ribs can have a lateral spacing of between about 2 and 10 mm. This increased size of the surface structures enables test surfaces to be manufactured with conventional mechanical methods, and it also enables us to build test surfaces with adjustable geometry. In addition, the Berlin oil channel has a novel shear stress balance with an unprecedented accuracy of ±0.3%. This latter feature is a prerequisite for a systematic experimental optimization.

In the present investigation, surfaces with longitudinal ribs and additional slits are studied. The experiments cover a fairly large range of parameters so that the drag reduction potential of a surface with ribs and/or slits is worked out conclusively. A large parameter range is made possible because of the adjustability of the surfaces as well as the automatic operation of the oil channel. In particular, the following tests were run:

(i) Shear stress measurements with conventional riblet configurations, i.e. with triangular and semi-circular grooves, have been carried out. These measurements were necessary in order to establish the connection between our oil channel data and previous data from wind tunnels. As was previously established, we found a drag reduction of about 5%.

(ii) An adjustable surface with longitudinal blade ribs and with slits was built and tested. Both groove depth and slit width could be varied separately and continuously during the experiment. It turned out, that slits in the surface did not contribute to the drag reduction. Nevertheless, these investigations show how perforated surfaces (e.g. for boundary-layer control) can be designed for minimal parasitic drag. On the other hand, with closed slits, an optimal groove depth for the rib surface could be determined, i.e. half of the lateral rib spacing. For this configuration, we found an 8.7% skin-friction reduction. By carefully eliminating deleterious effects (caused by little gaps, etc.), the skin-friction reduction could be improved to a record value of 9.9%.

(iii) A quantitative comparison between theory and experiment was carried out. The theory is based on the assumption that riblets impede the fluctuating turbulent crossflow near the wall. In this way, momentum transfer and shear stress are reduced. The simplified theoretical model proposed by Luchini (1992) is supported by the present experiments.

(iv) For technological applications of riblets, e.g. on long-range commercial aircraft, the above thin-blade ribs are not practical. Therefore, we have devised a surface that combines a significantly improved performance (8.2 %) with a geometry which exhibits better durability and enables previously developed manufacturing methods for plastic riblet film production to be used. Our riblet geometry exhibits trapezoidal grooves with wedge-like ribs. The flat floor of the trapezoidal grooves permits an undistorted visibility through the transparent riblet film which is essential for crack inspection on aircraft.

Type
Research Article
Copyright
© 1997 Cambridge University Press

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)
504
Cited by

Send article to Kindle

To send this article to your Kindle, first ensure no-reply@cambridge.org is added to your Approved Personal Document E-mail List under your Personal Document Settings on the Manage Your Content and Devices page of your Amazon account. Then enter the ‘name’ part of your Kindle email address below. Find out more about sending to your Kindle. Find out more about sending to your Kindle.

Note you can select to send to either the @free.kindle.com or @kindle.com variations. ‘@free.kindle.com’ emails are free but can only be sent to your device when it is connected to wi-fi. ‘@kindle.com’ emails can be delivered even when you are not connected to wi-fi, but note that service fees apply.

Find out more about the Kindle Personal Document Service.

Experiments on drag-reducing surfaces and their optimization with an adjustable geometry
Available formats
×

Send article to Dropbox

To send this article to your Dropbox account, please select one or more formats and confirm that you agree to abide by our usage policies. If this is the first time you use this feature, you will be asked to authorise Cambridge Core to connect with your <service> account. Find out more about sending content to Dropbox.

Experiments on drag-reducing surfaces and their optimization with an adjustable geometry
Available formats
×

Send article to Google Drive

To send this article to your Google Drive account, please select one or more formats and confirm that you agree to abide by our usage policies. If this is the first time you use this feature, you will be asked to authorise Cambridge Core to connect with your <service> account. Find out more about sending content to Google Drive.

Experiments on drag-reducing surfaces and their optimization with an adjustable geometry
Available formats
×
×

Reply to: Submit a response

Please enter your response.

Your details

Please enter a valid email address.

Conflicting interests

Do you have any conflicting interests? *