Book contents
- Design and Processing of Particulate Products
- Cambridge Series in Chemical Engineering
- Design and Processing of Particulate Products
- Copyright page
- Dedication
- Contents
- Contributors
- Preface
- 1 Introduction
- 2 Particle Characterization and Particle Property Distributions
- 3 The Population Balance
- 4 Industrial Crystallization
- 5 Particle Size Reduction
- 6 Aerosol Processes
- 7 Spray Drying and Spray Cooling
- 8 Wet Granulation
- 9 Strength, Breakage, and Attrition of Particulate Delivery Forms
- 10 Dispersion, Disintegration, and Dissolution
- Index
- References
10 - Dispersion, Disintegration, and Dissolution
Published online by Cambridge University Press: 03 November 2016
Book contents
- Design and Processing of Particulate Products
- Cambridge Series in Chemical Engineering
- Design and Processing of Particulate Products
- Copyright page
- Dedication
- Contents
- Contributors
- Preface
- 1 Introduction
- 2 Particle Characterization and Particle Property Distributions
- 3 The Population Balance
- 4 Industrial Crystallization
- 5 Particle Size Reduction
- 6 Aerosol Processes
- 7 Spray Drying and Spray Cooling
- 8 Wet Granulation
- 9 Strength, Breakage, and Attrition of Particulate Delivery Forms
- 10 Dispersion, Disintegration, and Dissolution
- Index
- References
Summary
A summary is not available for this content so a preview has been provided. Please use the Get access link above for information on how to access this content.
- Type
- Chapter
- Information
- Design and Processing of Particulate Products , pp. 294 - 322Publisher: Cambridge University PressPrint publication year: 2016
References
Bagster, D.F. and Tomi, D., 1974. The stresses within a sphere in simple flow fields. Chemical Engineering Science, 29, 1773–1783.CrossRefGoogle Scholar
Bohin, F., Manas-Zloczower, I., and Feke, D.L., 1994. Penetration of silicone polymers into silica agglomerates and its influence on dispersion mechanism. Rubber Chemistry and Technology, 67(4), 602–609.CrossRefGoogle Scholar
Boyle, J.F., Manas-Zloczower, I., and Feke, D.L., 2005. Hydrodynamic analysis of the mechanisms of agglomerate dispersion. Powder Technology, 153, 127–133.CrossRefGoogle Scholar
Calvert, G., Ghadiri, M., and Tweedie, R., 2009. Aerodynamic dispersion of cohesive powders: A review of understanding and technology. Advanced Powder Technology, 20(1), 4–16.CrossRefGoogle Scholar
Diao, J. and Fuerstenau, D.W., 1991. Characterization of the wettability of solid particles by film flotation 2. Theoretical analysis. Colloids and Surfaces, 60, 145–160.CrossRefGoogle Scholar
Evans, A.G. and Wilshaw, T.R., 1976. Quasi-static solid particle damage in brittle solids – I. Observations analysis and implications. Acta Metallurgica, 24(10), 939–956.CrossRefGoogle Scholar
Gentzler, M. and Michaels, J.N., 2004. Impact attrition of brittle structured particles at low velocities: Rigorous use of a laboratory vibrational impact tester. Chemical Engineering Science, 59(24), 5949–5958.CrossRefGoogle Scholar
Harriott, P., 1962. Mass transfer to particles: Part I. Suspended in agitated tanks. AIChE Journal, 8(1), 93–101.CrossRefGoogle Scholar
Masuda, H. and Gotoh, K., 1995. Performance evaluation of dry dispersers. Advanced Powder Technology, 6(4), 305–315.CrossRefGoogle Scholar
Pangarkar, V. and Yawalkar, A., 2002. Particle–liquid mass transfer coefficient in two-/three-phase stirred tank reactors. Industrial & Engineering Chemistry Research, 41(17), 4141–4167.CrossRefGoogle Scholar
Ranz, W. and Marshall, W., 1952. Evaporation from drops. 2. Chemical Engineering Progress, 48(4), 173–180.Google Scholar
Scurati, A., Feke, D.L. and Manas-Zloczower, I., 2005. Analysis of the kinetics of agglomerate erosion in simple shear flows. Chemical Engineering Science, 60, 6564–6573.CrossRefGoogle Scholar
Subero, J. and Ghadiri, M., 2001. Breakage patterns of agglomerates. Powder Technology, 120, 232–243.CrossRefGoogle Scholar
Yang, X.F. and Xi, X.M., 1995. Critical wetting angle for spontaneous liquid infiltration into orderly packed fibres or spheres. Journal of Materials Science, 30(20), 5099–5102.CrossRefGoogle Scholar
- 1
- Cited by