FFD (free-form deformation method) is one of the most commonly used parameterisation methods at present. It places the parameterised objects inside the control volume through coordinate system transformation, and controls the control volume through control points, thus realising the deformation control of its internal objects. Firstly, this paper systematically analyses and compares the characteristics and technical requirements of Bernstein, B-spline and NURBS (non-uniform rational b-splines) basic functions that can be adopted by FFD, and uses the minimum number of control points required to achieve the specified control effect threshold to express the control capability. Aiming at the problem of discontinuity at the right end in the actual calculation of B-spline basis function, a method of adding a small epsilon is proposed to solve it. Then, three basic functions are applied to the FFD parameterisation method, respectively, and the differences are compared from two aspects of the accurate expression of the model and the ability of deformation control. It is found that the BFFD (b-spline free-form deformation) approach owns better comprehensive performance when the control points are distributed correctly. In this paper, the BFFD method is improved, and a p-BFFD (reverse solution points based BFFD) method based on inverse solution is proposed to realise the free distribution of control points under the specified topology. Further, for the lifting body configuration, the control points of the p-BFFD method are brought closer to the airframe forming the EDGE-p-BFFD (edge constraints based p-BFFD) method. For the case in this paper, the proposed EDGE-p-BFFD method not only has fairly high parameterisation accuracy, but also reduces the expression error from 1.01E-3 to 1.25E-4, which is nearly ten times. It can also achieve effective lifting body guideline constraints, and has the ability of local deformation adapting to the configuration characteristics. In terms of the proportion of effective control points, the EDGE-p-BFFD method increases the proportion of effective control points from 36.7% to 50%, and the more control points, the more obvious the proportion increase effect. The new method also has better effect on the continuity of geometric deformation. At the same time, this paper introduces the independent deformation method of the upper and lower surfaces based on the double control body frames, which effectively avoids the deformation coupling problem of the simultaneous change of the upper and lower surfaces caused by the movement of control points in the traditional single control framework.

The pulsed jet is a novel and effective active mixing enhancement approach. For the transverse pulsed jet in the supersonic crossflow, the frequency influence is investigated using the three-dimensional Reynolds-averaged Navier–Stokes (RANS) equations coupled with the SST k-ω turbulence model. The averaged flow field properties of the pulsed jet are better than those of the steady jet when considering mixing efficiency and jet penetration depth, especially for the case with the pulsed frequency being 50kHz. The flow field structures of the pulsed jet are connected with the time, with periodic wave structures generating in the flow field and moving downstream. The size of the wave structures and its distance are related to the frequency, namely the size and flow distance are relatively small at 50kHz, and it takes some time for the pulsed jet to establish its influence in the full flow field. At low frequencies, the flow field produces large fluctuations, and this may be detrimental to the stable operation of the engine.

Planting patterns have significant effects on rice growth. Nonetheless, little is known about differences in annual crop yield and resource utilization among mechanized rice planting patterns in a rice–wheat cropping system. Field experiments were conducted from 2014 to 2017 using three treatments: pot seedling transplanting for rice and row sowing for wheat (PST-RS), carpet seedling transplanting for rice and row sowing for wheat (CST-RS) and row sowing for both crops (RS-RS). The results showed that, compared with RS-RS, PST-RS and CST-RS prolonged annual crop growth duration by 25–26 and 13–15 days, increased effective accumulated temperature by 399 and 212°C days and increased cumulative solar radiation by 454 and 228 MJ/m2 because of the earlier sowing of rice by 28 and 16 days in PST-RS and CST-RS, respectively. Compared with RS-RS, the annual crop yield of PST-RS and CST-RS increased by 3.1–3.8 and 2.0–2.6 t/ha, respectively, because of the increase in the number of spikelets/kernels per hectare, aboveground biomass, mean leaf area index and grain–leaf ratio. In addition, temperature production efficiency, solar radiation production efficiency and solar radiation use efficiency were higher in PST-RS, followed by CST-RS and RS-RS. These results suggest that mechanized rice planting patterns such as PST-RS increase annual crop production in rice–wheat cropping systems by increasing yield and solar energy utilization.

The great demographic pressure brings tremendous volume of beef demand. The key to solve this problem is the growth and development of Chinese cattle. In order to find molecular markers conducive to the growth and development of Chinese cattle, sequencing was used to determine the position of copy number variations (CNVs), bioinformatics analysis was used to predict the function of ZNF146 gene, real-time fluorescent quantitative polymerase chain reaction (qPCR) was used for CNV genotyping and one-way analysis of variance was used for association analysis. The results showed that there exists CNV in Chr 18: 47225201-47229600 (5.0.1 version) of ZNF146 gene through the early sequencing results in the laboratory and predicted ZNF146 gene was expressed in liver, skeletal muscle and breast cells, and was amplified or overexpressed in pancreatic cancer, which promoted the development of tumour through bioinformatics. Therefore, it is predicted that ZNF146 gene affects the proliferation of muscle cells, and then affects the growth and development of cattle. Furthermore, CNV genotyping of ZNF146 gene was three types (deletion type, normal type and duplication type) by Real-time fluorescent quantitative PCR (qPCR). The association analysis results showed that ZNF146-CNV was significantly correlated with rump length of Qinchuan cattle, hucklebone width of Jiaxian red cattle and heart girth of Yunling cattle. From the above results, ZNF146-CNV had a significant effect on growth traits, which provided an important candidate molecular marker for growth and development of Chinese cattle.

The epidemic of tuberculosis has posed a serious burden in Qinghai province, it is necessary to clarify the epidemiological characteristics and spatial-temporal distribution of TB for future prevention and control measures. We used descriptive epidemiological methods and spatial statistical analysis including spatial correlation and spatial-temporal analysis in this study. Furthermore, we applied an exponential smoothing model for TB epidemiological trend forecasting. Of 43 859 TB cases, the sex ratio was 1.27:1 (M:F), and the average annual TB registered incidence was 70.00/100 000 of 2009–2019. More cases were reported in March and April, and the worst TB stricken regions were the prefectures of Golog and Yushu. High TB registered incidences were seen in males, farmers and herdsmen, Tibetans, or elderly people. 7132 cases were intractable, which were recurrent, drug resistant, or co-infected with other infections. Three likely cases clusters with significant high risk were found by spatial-temporal scan on data of 2009–2019. The exponential smoothing winters' additive model was selected as the best-fitting model to forecast monthly TB cases in the future. This research indicated that TB in Qinghai is still a serious threaten to the local residents' health. Multi-departmental collaboration and funds special for TB treatments and control are still needed, and the exponential smoothing model is promising which could be applied for forecasting of TB epidemic trend in this high-altitude province.

The extent of the reduction of maize (Zea mays L.) kernel moisture content through drying is closely related to field temperature (or accumulated temperature; AT) following maturation. In 2017 and 2018, we selected eight maize hybrids that are widely planted in Northeastern China to construct kernel drying prediction models for each hybrid based on kernel drying dynamics. In the traditional harvest scenario using the optimal sowing date (OSD), maize kernels underwent drying from 4th September to 5th October, with variation coefficients of 1.0–1.9. However, with a latest sowing date (LSD), drying occurred from 14th September to 31st October, with variation coefficients of 1.3–3.0. In the changed harvest scenario, the drying time of maize sown on the OSD condition was from 12th September to 9th November with variation coefficients of 1.3–3.0, while maize sown on the LSD had drying dates of 26th September to 28th October with variation coefficients of 1.5–3.6. In the future harvest scenario, the Fengken 139 (FK139) and Jingnongke 728 (JNK728) hybrids finished drying on 20th October and 8th November, respectively, when sown on the OSD and had variation coefficients of 2.7–2.8. Therefore, the maize kernel drying time was gradually delayed and was associated with an increased demand for AT ⩾ 0°C late in the growing season. Furthermore, we observed variation among different growing seasons likely due to differences in weather patterns, and that sowing dates impact variations in drying times to a greater extent than harvest scenarios.

We prospectively surveyed SARS-CoV-2 RNA contamination in staff common areas within an acute-care hospital. An increasing prevalence of surface contamination was detected over time. Adjusting for patient census or community incidence of coronavirus disease 2019 (COVID-19), the proportion of contaminated surfaces did not predict healthcare worker COVID-19 infection on study units.

The fundamental nature of turbulent density fluctuations in standard Wendelstein 7-X (W7-X) stellarator discharges is investigated experimentally via phase contrast imaging (PCI) in combination with gyrokinetic simulations with the code GENE. We find that density fluctuations are ion-temperature-gradient-driven and radially localised in the outer half of the plasma. It is shown that the line-integrated PCI measurements cover the right range of wavenumbers and a favourable toroidal and poloidal location to capture some of the strongest density fluctuations in W7-X. Due to the radial localisation of fluctuations, measured wavenumber–frequency spectra exhibit a dominant phase velocity, which can be related to the $\boldsymbol {E\times B}$ rotation velocity at the radial position of a well in the neoclassical radial electric field. The match is robust against variations of heating power and line-integrated density, which is partly due to the localisation of fluctuations and partly due to effects of the radial gradient in the $\boldsymbol {E\times B}$ velocity profile on the wavenumber–frequency spectrum. The latter effect is studied with a newly built synthetic PCI diagnostic and global gyrokinetic simulations with GENE-3D.

Severe fever with thrombocytopenia syndrome (SFTS) is a disease with a high case-fatality rate that is caused by infection with the SFTS virus (SFTSV). Five electronic databases were systematically searched to identify relevant articles published from 1 January 2011 to 1 December 2019. The pooled rates with 95% confidence interval (CI) were calculated by a fixed-effect or random-effect model analysis. The results showed that 92 articles were included in this meta-analysis. For the confirmed SFTS cases, the case-fatality rate was 0.15 (95% CI 0.11, 0.18). Two hundred and ninety-six of 1384 SFTS patients indicated that they had been bitten by ticks and the biting rate was 0.21 (95% CI 0.16, 0.26). The overall pooled seroprevalence of SFTSV antibodies among the healthy population was 0.04 (95% CI 0.03, 0.05). For the overall seroprevalence of SFTSV in animals, the seroprevalence of SFTSV was 0.25 (95% CI 0.20, 0.29). The infection rate of SFTSV in ticks was 0.08 (95% CI 0.05, 0.11). In conclusion, ticks can serve as transmitting vectors of SFTSVs and reservoir hosts. Animals can be infected by tick bites, and as a reservoir host, SFTSV circulates continuously between animals and ticks in nature. Humans are infected by tick bites and direct contact with patient secretions.

We consider the numerical solution of competitive exothermic and endothermic reactions in the presence of a chaotic advection flow. The resulting behaviour is characterized by a strong dependence on the competitive reaction history. The burnt temperature is not immediately connected to simple enthalpy calculations, so there is a subtlety in the interplay between the major parameters, notably the Damköhler number, the ratio of the heats of exothermic and endothermic reactions, as well as the ratio of their respective activation energies. This paper seeks to explore the way these parameters affect the steady states of these reaction fronts and their stability.

The aim of this study was to develop and externally validate a simple-to-use nomogram for predicting the survival of hospitalised human immunodeficiency virus/acquired immunodeficiency syndrome (HIV/AIDS) patients (hospitalised person living with HIV/AIDS (PLWHAs)). Hospitalised PLWHAs (n = 3724) between January 2012 and December 2014 were enrolled in the training cohort. HIV-infected inpatients (n = 1987) admitted in 2015 were included as the external-validation cohort. The least absolute shrinkage and selection operator method was used to perform data dimension reduction and select the optimal predictors. The nomogram incorporated 11 independent predictors, including occupation, antiretroviral therapy, pneumonia, tuberculosis, Talaromyces marneffei, hypertension, septicemia, anaemia, respiratory failure, hypoproteinemia and electrolyte disturbances. The Likelihood χ2 statistic of the model was 516.30 (P = 0.000). Integrated Brier Score was 0.076 and Brier scores of the nomogram at the 10-day and 20-day time points were 0.046 and 0.071, respectively. The area under the curves for receiver operating characteristic were 0.819 and 0.828, and precision-recall curves were 0.242 and 0.378 at two time points. Calibration plots and decision curve analysis in the two sets showed good performance and a high net benefit of nomogram. In conclusion, the nomogram developed in the current study has relatively high calibration and is clinically useful. It provides a convenient and useful tool for timely clinical decision-making and the risk management of hospitalised PLWHAs.

The analysis of the aerodynamic environment of the re-entry vehicle attaches great importance to the design of the novel drag reduction strategies, and the combinational spike and jet concept has shown promising application for the drag reduction in supersonic flows. In this paper, the drag force reduction mechanism induced by the combinational spike and lateral jet concept with the freestream Mach number being 5.9332 has been investigated numerically by means of the two-dimensional axisymmetric Navier-Stokes equations coupled with the shear stress transport (SST) k-ω turbulence model, and the effects of the lateral jet location and its number on the drag reduction of the blunt body have been evaluated. The obtained results show that the drag force of the blunt body can be reduced more profoundly when employing the dual lateral jets, and its maximum percentage is 38.81%, with the locations of the first and second lateral jets arranged suitably. The interaction between the leading shock wave and the first lateral jet has a great impact on the drag force reduction. The drag force reduction is more evident when the interaction is stronger. Due to the inclusion of the lateral jet, the pressure intensity at the reattachment point of the blunt body decreases sharply, as well as the temperature near the walls of the spike and the blunt body, and this implies that the multi-lateral jet is beneficial for the drag reduction.

Tuberculosis (TB) is the leading cause of death among infectious diseases. China has a high burden of TB and accounted for almost 13% of the world's cases of multi-drug resistant (MDR) TB. Spinal TB is one reason for the resurgence of TB in China. Few large case studies of MDR spinal TB in China have been conducted. The aim of this research was to observe the epidemiological characteristics of inpatients with MDR spinal TB in six provinces and cities of China from 1999–2015. This is a multicentre retrospective observational study. Patients' information was collected from the control disease centre and infectious disease database of hospitals in six provinces and cities in China. A total of 3137 patients with spinal TB and 272 patients with MDR spinal TB were analysed. The result showed that MDR spinal TB remains a public health concern and commonly affects patients 15–30 years of age (34.19%). The most common lesions involved the thoracolumbar spine (35.66%). Local pain was the most common symptom (98.53%). Logistic analysis showed that for spinal TB patients, reside in rural district (OR 1.79), advanced in years (OR 1.92) and high education degree (OR 2.22) were independent risk factors for the development of MDR spinal TB. Women were associated with a lower risk of MDR spinal TB (OR 0.48). The most common first-line and second-line resistant drug was isoniazid (68.75%) and levofloxacin (29.04%), respectively. The use of molecular diagnosis resulted in noteworthy clinical advances, including earlier initiation of MDR spinal TB treatment, improved infection control and better clinical outcome. Chemotherapy and surgery can yield satisfactory outcomes with timely diagnosis and long-term treatment. These results enable a better understanding of the MDR spinal TB in China among the general public.