The damage characteristics of fused silica were investigated under low-temporal coherence light (LTCL). It was found that the laser-induced damage threshold (LIDT) of fused silica for the LTCL was lower than that of the single longitudinal mode pulse laser, and for the LTCLs, the LIDTs decrease with the increasing of laser bandwidth, which is not consistent with the temporal spike intensity. This is due to the nonlinear self-focusing effect and multi-pulse accumulation effect. The specific reasons were analyzed based on theoretical simulation and experimental study. This research work is helpful and of great significance for the construction of high-power LTCL devices.

Todorokite is a common Mn oxide (with a tunnel structure) in the Earth surface environment, and can be obtained by hydrothermal treatment or refluxing process from precursor buserite with a layered structure. Several chemical reaction conditions for the phase transformation from Na-buserite to todorokite at atmospheric pressure were investigated, including temperature, pH, crystallinity of precursor Na-buserite, the amount of the interlayer Mg2+ of the Mg-buserite and clay minerals. The results showed that the conversion rate and crystallinity of todorokite decreased with falling temperature, and Mg-buserite could not be completely transformed to todorokite at lower temperatures (40°C). The poorly crystalline Na-buserite could be converted into todorokite more easily than highly crystalline Na-buserite. Todorokite can be prepared at pH 5–9, but the rate of conversion and crystallinity of todorokite did vary with pH in the order: neutral ≈ alkali > acidic. The conversion rate of todorokite decreased with decreasing interlayer Mg2+ content of the Mg-buserite. The presence of montmorillonite or goethite slowed the formation reaction of todorokite in the refluxing process, and the reaction time was prolonged when the amounts of those minerals were increased.

Advanced Ni8W/Ni12W/Ni8W alloy composite substrates used in YBCO-coated conductors with a strong cube texture and high yield strength have been fabricated, and a CeO2 buffer layer film was successfully deposited on the composite substrates. Through in situ tensile testing coupled with electron backscattered diffraction (EBSD) analysis, the stability of the cube texture of Ni8W/Ni12W/Ni8W alloy composite substrates has been investigated. The stress–strain curve shows that the yield strength (at 0.2% strain) of the composite substrates exceeds 250 Mpa. The orientation of grains and boundaries on the surface of the substrates was almost unchanged, while the strain exceeds 0.2%, which indicated that the composite substrates are adequate for depositing buffer layers and YBCO layers by the reel-to-reel process.

A novel solid-clad-by-liquid method was developed to form a 10-m long by 10-mm wide by 80-μm thick Ni–5 at.% W/Ni–9.3 at.% W/Ni–5 at.% W composite tape. Three deformation routes (cold rolling, cold rolling with intermediate annealing, and cold rolling combined with warm rolling) have been investigated in short Ni–5 at.% W/Ni–9.3 at.% W/Ni–5 at.% W composite substrate. To optimize the dynamic continuous annealing parameters for the long composite substrates, air-cooled and furnace-cooled annealing procedures were compared in short Ni–5 at.% W/Ni–9.3 at.% W/Ni–5 at.% W composite substrates. Improved cube texture of 98.7% in a 10-m long by 10-mm wide by 80-μm thick Ni–5 at.% W/Ni–9.3 at.% W/Ni–5 at.% W composite substrate was achieved via warm rolling deformation at 550 °C and two-step dynamic continuous annealing (750 °C for 1 h followed by 1200 °C for 1 h). The yield strength, Curie temperature, and saturation magnetization of 176 MPa, 324 K, and 18 emu/g, respectively, were obtained.

Novel NiMoO4-integrated electrode materials were successfully prepared by solvothermal method using Na2MoO4·2H2O and NiSO4·6H2O as main raw materials, water, and ethanol as solvents. The morphology, phase, and structure of the as-prepared materials were characterized by SEM, XRD, Raman, and FT-IR. The electrochemical properties of the materials in supercapacitors were investigated by cyclic voltammetry, constant current charge–discharge, and electrochemical impedance spectroscopy techniques. The effects of volume ratio of water to ethanol (W/E) in solvent on the properties of the product were studied. The results show that the pure phase monoclinic crystal NiMoO4 product can be obtained when the W/E is 2:1. The diameter and length are 0.1–0.3 µm and approximately 3 µm, respectively. As an active material for supercapacitor, the NiMoO4 nanorods material delivered a discharge specific capacitance of 672, 498, and 396 F/g at a current density of 4, 7, and 10 A/g, respectively. The discharge specific capacitance slightly decreased from 815 to 588 F/g with a retention of 72% after 1000 cycles at a current density of 1 A/g. With these superior capacitance properties, the novel NiMoO4 integrated electrode materials could be considered as promising material for supercapacitors.

In order to diminish the occurrence of cavitation bubbles during the liquid-assisted laser machining, ultrasound-assisted underwater femtosecond laser drilling on stainless steel is adopted. This method greatly diminishes the optical disturbance of cavitation bubbles. By investigating and analyzing the effect of laser pulse energy and pulse number on the morphology of the holes, it has been found that ultrasound not only has a remarkable function of forming a hole with clean and flat bottom, but also reduces debris redeposition around the processing area. This method improves the machining quality. Besides, it also improves the depth-to-diameter ratio of the hole about 20%.

The trace elements in quartz, Al and Ti, contain considerable information about mineral genesis, and determining their concentrations is of great importance in geology. Electron probe microanalysis has the advantages of non-destructive testing and high spatial resolution; however, it is a challenge to improve the accuracy and precision of trace element detection using this method. The important factors affecting accuracy include the fragility of quartz lattices at high beam currents and the methods used to determine the background. In this paper, the peaks of Al-Kα and Ti-Kα, and their backgrounds, were found to exhibit intensity variations at high beam currents and small beam diameters; therefore, it is necessary to select a large beam diameter (up to 20 µm) to avoid variations in intensity at high currents (500 nA). For background determination of Al, a multipoint background method is proposed to determine the background value, which greatly improves the accuracy of the results. For Ti, the choice of background measurement does not affect the result. In addition, it is verified that the background obtained from other quartz samples can be used as the background of an unknown quartz sample, which reduces the analysis time and minimizes sample damage.

The present study was performed to identify the genotype of a hypertrophic cardiomyopathy family and investigate the clinicopathogenic characteristics and prognostic features of relevant genetic abnormalities. Target sequence capture sequencing was performed to screen for pathogenic alleles in a 32-year-old female patient (proband). Sanger sequencing was carried out to verify the results. Sanger sequencing was also performed on other family members to identify allele carriers. A survival analysis was carried out using published literature and our findings. We found that the proband and her son harboured a Gly716Arg sequence variant of the β-myosin heavy chain. Neither the proband’s father nor the mother were carriers of this sequence variant; thus, the mutation was classified as “de novo”. Further survival analysis revealed that female patients appear to have a longer life expectancy compared with males. Our study may provide an effective approach for the genetic diagnosis of hypertrophic cardiomyopathy.

The microstructural evolution of spray-formed high speed steel during hot deformation was investigated as well as the effects of spray forming parameters on the porosity formation. Four distinct zones are identified in the as-deposited material, and interstitial porosity is present in the bottom and peripheral zones, while gas-related porosity is mainly found in the central zone. It can keep the porosity at a minimum value by using the optimum parameters, e.g., the average porosity of central zone is 3.7% for a superheat of 170 °C and a gas-to-metal flow rate of 0.7. During hot deformation at 1150 °C, the amount of porosity can be obviously decreased by increasing the height reduction which also plays a key role in breaking up eutectic carbides. The critical height reduction for the breakdown of the eutectic carbides is 50%, the dominant mechanism being mechanical fragmentation.

Yang L, Ruan L-M, Ye H-H, Cui H-B, Mu Q-T, Lou Y-R, Ji Y-X, Li W-Z, Sun D-H, Chen X-B. Depression is associated with lower circulating endothelial progenitor cells and increased inflammatory markers.

Objective: To test the hypothesis that depression status in subjects without cardiovascular diseases (CVD) or diabetes is associated with depletion of circulating endothelial progenitor cells (EPCs) and impaired endothelial function.

Method: Thirty depressive persons with the first episode of depression (case group) diagnosed according to Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition (DSM-IV) and 30 healthy people (control group) were investigated. The depression status was estimated using Hamilton Rating Scale of Depression from which the criteria of depression are determined to be >21 score. EPCs labeled with CD34-ECD, CD133-phycoerythrin and kinase insert domain receptor (KDR)-fluorescein isothiocyanate antibodies were counted by flow cytometry in the peripheral blood of patients and control subjects. Mononuclear cells that were positive for CD34/KDR, CD133/KDR and CD34/CD133/KDR within the lymphocyte population were characterised as different phenotypes of EPCs.

Results: There were no significant differences in baseline clinical characteristics between patients and healthy individuals (all p > 0.05). However, patients with depression had significantly lower levels of circulating CD34+CD133+KDR+ EPCs (132.20 ± 17.27 vs. 225.93 ± 9.88, p = 0.000) and endothelial colony-forming units (26.40 ± 3.79 vs. 36.60 ± 2.88, p = 0.000) than that of healthy subjects. Furthermore, CD34+CD133+KDR+ EPCs had a negative correlation with tumour necrosis factor-α (Spearman's ρ = 0.433, p = 0.000) and interleukin-6 (Spearman's ρ = 0.441, p = 0.032).

Conclusion: Our result shows that depression was associated with lower levels of circulating EPCs, which may contribute to the development of endothelial dysfunction and atherosclerosis.

In vitro fertilized (IVF) human embryos have a high incidence of developmental arrest before the blastocyst stage, therefore characterization of the molecular mechanisms that regulate embryo development is urgently required. Post-transcriptional control by microRNAs (miRNAs) is one of the most investigated RNA control mechanisms, and is hypothesized to be involved actively in developmental arrest in preimplantation embryos. In this study, we extracted total RNA from mouse 2-cell and 4-cell embryos. Using a miRNA microarray, 192 miRNAs were found to be differentially expressed in 4-cell embryos and 2-cell embryos; 122 miRNAs were upregulated and 70 were downregulated in 4-cell embryos. The microarray results were confirmed by real-time quantitative RT-PCR for six miRNAs (mmu-miR-467h, mmu-miR-466d-3p, mmu-miR-292–5p, mmu-miR-154, mmu-miR-2145, and mmu-miR-706). Cdca4 and Tcf12 were identified as miR-154 target genes by target prediction analysis. This study provides a developmental map for a large number of miRNAs in 2-cell and 4-cell embryos. The function of these miRNAs and the mechanisms by which they modulate embryonic developmental arrest require further study. The results of this study have potential applications in the field of reproductive medicine.

This paper investigates task allocation for multiple robots by applying the game theory-based negotiation approach. Based on the initial task allocation using a contract net-based approach, a new method to select the negotiation robots and construct the negotiation set is proposed by employing the utility functions. A negotiation mechanism suitable for the decentralized task allocation is also presented. Then, a game theory-based negotiation strategy is proposed to achieve the Pareto-optimal solution for the task reallocation. Extensive simulation results are provided to show that the task allocation solutions after the negotiation are better than the initial contract net-based allocation. In addition, experimental results are further presented to show the effectiveness of the approach presented.

At the summit of the Antarctic plateau, Dome A offers an intriguing location for future large scale optical astronomical observatories. The Gattini Dome A project was created to measure the optical sky brightness and large area cloud cover of the winter-time sky above this high altitude Antarctic site. The wide field camera and multi-filter system was installed on the PLATO instrument module as part of the Chinese-led traverse to Dome A in January 2008. This automated wide field camera consists of an Apogee U4000 interline CCD coupled to a Nikon fisheye lens enclosed in a heated container with glass window. The system contains a filter mechanism providing a suite of standard astronomical photometric filters (Bessell B, V, R) and a long-pass red filter for the detection and monitoring of airglow emission. The system operated continuously throughout the 2009, and 2011 winter seasons and part-way through the 2010 season, recording long exposure images sequentially for each filter. We have in hand one complete winter-time dataset (2009) returned via a manned traverse. We present here the first measurements of sky brightness in the photometric V band, cloud cover statistics measured so far and an estimate of the extinction.

HRCAM (High Resolution CAMera) is a Canon 50D 15-megapixel digital SLR camera equipped with a Sigma 4.5 mm f/2.8 fish-eye lens. It was installed at Dome A on the Antarctic plateau in January 2010 and photographs the sky every 15 minutes. Primarily functioning as a site-testing instrument, data obtained from HRCAM provide valuable statistics on cloud cover, sky transparency and the distribution and frequency of auroral activity. We present a first look at data from HRCAM during 2010, including an overview of how we intend to reduce the images. We also demonstrate the potential of stellar photometry by using linear combinations of the in-built Canon RGB filters to convert instrumental magnitudes into the photometric BVR bands.

In 2008 January the 24th Chinese expedition team successfully deployed the Chinese Small Telescope ARray (CSTAR) to Dome A, the highest point on the Antarctic plateau. CSTAR consists of four 14.5cm optical telescopes, each with a different filter (g, r, i and open) and has a 4.5°×4.5° field of view (FOV). Based on the CSTAR data, initial statistics of astronomical observational site quality and light curves of variable objects were obtained. To reach higher photometric quality, we are continuing to work to overcome the effects of uneven cirrus cloud cirrus, optical “ghosts” and intra-pixel sensitivity. The snow surface stability is also tested for further astronomical observational instrument and for glaciology studies.