Particle-resolved direct numerical simulations are employed to investigate the particle–particle drag force in the bidisperse gas–particle suspensions where the particles are smooth and the single-particle velocity distribution function is Maxwellian. The particle Reynolds number ranges from 6.7 to 123.8, and in this range the particle inertia is high enough that the lubrication force is not essential. It is found that the relation derived by the kinetic theory of granular flow (KTGF) highly overestimates the particle–particle drag force. This is because the pre-collision velocities of colliding particles are not completely uncorrelated with each other. From the time sequence of collision events, it is observed that the particle pair that has just collided will probably collide again after a short time due to the restriction of the particle motion in dense suspensions. Since the post-collision velocities of the first collision cannot relax entirely in such a short time, the relative velocity before the subsequent collision is statistically smaller than the domain-averaged relative velocity. Consequently, the particle–particle drag force is over-predicted when the domain-averaged relative velocity is used. For this reason, this work assumes that the particle–particle drag force is determined by the relative velocity within a local region near large particles. When the local region is set to be the spherical shells centred on the centres of large particles and with an outer radius of a mean free path of small particles, the KTGF-based relation can reasonably predict the particle–particle drag force.

To determine the association between hearing loss and environmental Pb, Cd and Se exposure, a total of 1503 American adults from National Health and Nutrition Examination Survey (NHANES) (2011–2012) were assessed. The average of four audiometric frequencies (0·5, 1, 2 and 4 kHz) was used to identify speech-frequency hearing loss (SFHL), while the average of 3 audiometric frequencies (3, 4 and 6 kHz) was used to identify high-frequency hearing loss (HFHL). HFHL adjusted OR determined by comparing the highest and lowest blood Pb and Cd quartiles were 1·98 (95 % CI: 1·27, 3·10) and 1·81 (95 % CI: 1·13, 2·90), respectively. SFHL was significantly associated with blood Cd with the OR = 2·42 for the highest quartile. When further stratified by age, this association appeared to be limited to adults aged 35–52 years. After stratified by gender, except for Pb and Cd, we observed that blood Se showed a dose-dependent association with SFHL in men. In women, only Cd showed a dose-dependent association with speech and high-frequency hearing loss. Hearing loss was positively associated with blood levels of Pb and Cd. Additionally, our study provided novel evidence suggesting that excessive Se supplement would increase SFHL risk in men.

The superfluorescent fiber source (SFS) with tunable optical spectrum has shown great application potential in the sensing, imaging, and spectral combination. Here, we demonstrate for the first time a 2-kW-level wavelength and linewidth tunable SFS. Based on a flexible filtered SFS seed and three stages of fiber amplifiers, the output power can be scaled from the milliwatt level to about 2 kW, with a wavelength tuning range of 1068–1092 nm and a linewidth tuning range of 2.5–9.7 nm. Moreover, a numerical simulation is conducted based on the generalized nonlinear Schrödinger equation, and the results reveal that the wavelength tuning range is limited by the decrease of seed power and the growth of amplified spontaneous emission, whereas the linewidth tuning range is determined by the gain competition and nonlinear Kerr effects. The developed wavelength and linewidth tunable SFS may be applied to scientific research and industrial processing.

The present study evaluated whether fat mass assessment using the triceps skinfold (TSF) thickness provides additional prognostic value to the Global Leadership Initiative on Malnutrition (GLIM) framework in patients with lung cancer (LC). We performed an observational cohort study including 2672 LC patients in China. Comprehensive demographic, disease and nutritional characteristics were collected. Malnutrition was retrospectively defined using the GLIM criteria, and optimal stratification was used to determine the best thresholds for the TSF. The associations of malnutrition and TSF categories with survival were estimated independently and jointly by calculating multivariable-adjusted hazard ratios (HR). Malnutrition was identified in 808 (30·2 %) patients, and the best TSF thresholds were 9·5 mm in men and 12 mm in women. Accordingly, 496 (18·6 %) patients were identified as having a low TSF. Patients with concurrent malnutrition and a low TSF had a 54 % (HR = 1·54, 95 % CI = 1·25, 1·88) greater death hazard compared with well-nourished individuals, which was also greater compared with malnourished patients with a normal TSF (HR = 1·23, 95 % CI = 1·06, 1·43) or malnourished patients without TSF assessment (HR = 1·31, 95 % CI = 1·14, 1·50). These associations were concentrated among those patients with adequate muscle mass (as indicated by the calf circumference). Additional fat mass assessment using the TSF enhances the prognostic value of the GLIM criteria. Using the population-derived thresholds for the TSF may provide significant prognostic value when used in combination with the GLIM criteria to guide strategies to optimise the long-term outcomes in patients with LC.

Drilling and sampling are the most direct and effective methods available to study Antarctic subglacial lakes. Based on the Philberth probe, a Recoverable Autonomous Sonde (RECAS) allows for in situ lake water measurement and sampling, through the addition of an upper thermal tip and a cable recoiling mechanism. RECAS-200, a prototype of RECAS, has a drilling depth of 200 m, a surface supply voltage of 800 VAC and a downhole power of ~9.6 kW during drilling. In this study, a heating control system for RECAS-200 was designed. The system avoids the need for high-power step-down converters, by separating heating power from control power, thereby reducing the overall weight of the probe and avoiding the need to increase cable diameter. We also introduce a self-developed, small, solid-state, 800 VAC power regulator and a fuzzy PID temperature control algorithm. Their purpose was to manage the power adjustment of each heating element and to provide closed-loop temperature control of certain heating elements which can easily burn out due to overheating. Test results indicated that the proposed RECAS-200 heating control system met all our design specifications and could be easily assembled into the RECAS-200 probe.

Subglacial lake exploration is of great interest to the science community. RECoverable Autonomous Sonde (RECAS) provides an exploration tool to measure and sample subglacial lake environments while the subglacial lake remains isolated from the glacier surface and atmosphere. This paper presents an electronic control system design of 200 m prototype of RECAS. The proposed electronic control system consists of a surface system, a downhole control system, and a power transfer and communication system. The downhole control system is the core element of RECAS, and is responsible for sonde status monitoring, sonde motion control, subglacial water sampling and in situ analysis. A custom RS485 temperature sensor was developed to cater for the limited size and depth requirements of the system. We adopted a humidity-based measurement to monitor for a housing leak. This condition is because standard leak detection monitoring of water conductivity may be inapplicable to pure ice in Antarctica. A water sampler control board was designed to control the samplers and monitor the on/off state. A high-definition camera system with built-in storage and self-heating ability was designed to perform the video recording in the subglacial lake. The proposed electronic control system is proven effective after a series of tests.

In glaciology, snow–firn temperature at 10 m is considered a representation of the mean annual air temperature at the surface (MAAT) of the studied site. Although MAAT is an important parameter in ice-sheet investigations, it has not been widely measured in Antarctica. To measure the 10 m snow–firn temperature in Antarctica, a shallow hot-point drill system is designed. In this simple and lightweight system, a hot-point drill can melt boreholes with a diameter of 34 mm in the snow–firn to a depth of 30 m and a temperature sensors string can measure the borehole temperature precisely. In the 2018/19 field season, 16 boreholes along the Zhongshan–Dome A traverse were drilled, and the borehole temperature was measured. Although certain problems existed pertaining to the hot-point drill, a total depth of ~244 m was successfully drilled at an average penetration rate of ~10 m h−1. After borehole drilling, ~12–15 h were generally required for the borehole to achieve thermal equilibrium with the surroundings. Preliminary results demonstrated that the 10 m snow–firn temperature along the traverse route was affected by the increasing altitude and latitude, and it decreased gradually with an increase in the distance from Zhongshan station.

The association between dietary Fe intake and diabetes risk remains inconsistent. We aimed to explore the association between dietary Fe intake and type 2 diabetes mellitus (T2DM) risk in middle-aged and older adults in urban China. This study used data from the Guangzhou Nutrition and Health Study, an on-going community-based prospective cohort study. Participants were recruited from 2008 to 2013 in Guangzhou community. A total of 2696 participants aged 40–75 years without T2DM at baseline were included in data analyses, with a median of 5·6 (interquartile range 4·1–5·9) years of follow-up. T2DM was identified by self-reported diagnosis, fasting glucose ≥ 7·0 mmol/l or glycosylated Hb ≥ 6·5 %. Cox proportional hazard models were used to estimate hazard ratios (HR) and 95 % CI. We ascertained 205 incident T2DM cases during 13 476 person-years. The adjusted HR for T2DM risk in the fourth quartile of haem Fe intake was 1·92 (95 % CI 1·07, 3·46; Ptrend = 0·010), compared with the first quartile intake. These significant associations were found in haem Fe intake from total meat (HR 2·74; 95 % CI 1·22, 6·15; Ptrend = 0·011) and haem Fe intake from red meat (HR 1·86; 95 % CI 1·01, 3·44; Ptrend = 0·034), but not haem Fe intake from processed meat, poultry or fish/shellfish. The association between dietary intake of total Fe or non-haem Fe with T2DM risk had no significance. Our findings suggested that higher dietary intake of haem Fe (especially from red meat), but not total Fe or non-haem Fe, was associated with greater T2DM risk in middle-aged and older adults.

We study the predictive power of option-implied moment risk premia embedded in the conventional variance risk premium. We find that although the second-moment risk premium predicts market returns in short horizons with positive coefficients, the third-moment (fourth-moment) risk premium predicts market returns in medium horizons with negative (positive) coefficients. Combining the higher-moment risk premia with the second-moment risk premium improves the stock return predictability over multiple horizons, both in sample and out of sample. The finding is economically significant in an asset-allocation exercise and survives a series of robustness checks.

In this study, direct numerical simulation of the dispersion and motion of inertial particles in a spatially developing compressible turbulent boundary layer at a Mach number of 2 is performed with the Eulerian–Lagrangian point particle method. Two cases are simulated with different particle diameters (Stokes number) but identical inflow particle numbers. Statistical characteristics and preferential accumulation of particles in the very-near-wall and wake regions are systematically investigated through conditional sampling and mechanism analysis. The results reveal that particle streaks are formed in low-speed regions near the wall because of the influence of dominating ejection events. After normalization with the local minimum particle number density, the particle number density profile reveals a self-similar feature at different streamwise positions. Compared with small particles, large particles are more significantly influenced by turbophoresis and demonstrate stronger preferential accumulation; thus, more large particles are clustered in the near-wall regions and the deviation between the mean velocities of the particle and the fluid increases. With the wall effect, both large and small particles are selectively accumulated in high-vorticity regions in the buffer layer in contrast to turbulence without walls. In comparison with incompressible wall-bounded turbulence, a new mechanism for particle preferential accumulation based on local fluid density is discovered. Large particles are located in low-density regions in the inner zones and high-density regions in the outer zones. Nevertheless, small particles remain located in regions with low fluid density, as illustrated by the mechanism analysis of particle dilatation.

A higher dietary intake or serum concentration of betaine has been associated with greater lean body mass in middle-aged and older adults. However, it remains unknown whether betaine intake is associated with age-related loss of skeletal muscle mass (SMM). We assessed the association between dietary betaine intake and relative changes in SMM after 3 years in middle-aged adults. A total of 1242 participants aged 41–60 years from the Guangzhou Nutrition and Health Study 2011–2013 and 2014–2017 with body composition measurements by dual-energy X-ray absorptiometry were included. A face-to-face questionnaire was used to collect general baseline information. After adjustment for potential confounders, multiple linear regression found that energy-adjusted dietary betaine intake was significantly and positively associated with relative changes (i.e. percentage loss or increase) in SMM of legs, limbs and appendicular skeletal mass index (ASMI) over 3 years of follow-up (β 0·322 (se 0·157), 0·309 (se 0·142) and 0·303 (se 0·145), respectively; P < 0·05). The ANCOVA models revealed that participants in the highest betaine tertile had significantly less loss in SMM of limbs and ASMI and more increase in SMM of legs over 3 years of follow-up, compared with those in the bottom betaine tertile (all Ptrend < 0·05). In conclusion, our findings suggest that elevated higher dietary betaine intake may be associated with less loss of SMM of legs, limbs and ASMI in middle-aged adults.

The Antarctic subglacial drilling rig (ASDR) is designed to recover 105 mm-diameter ice cores up to 1400 m depth and 41.5 mm-diameter bedrock cores up to 2 m in length. In order to ensure safe and convenient drilling, drilling auxiliaries are designed to support fieldwork and servicing. These auxiliaries are subdivided into several systems for power supply, drill tripping in the borehole, ice core and chip processing, and drill servicing and maintenance. The required equipment also includes two generators, a drilling winch with a cable, logging winch with a cable, control desk, pipe handler with a fixed clamp, chip chamber vibrator, centrifuge, emergency devices and fitting and electrical tools. Additionally, several environmental protective measures such as a new liquid-tight casing with a thermal casing shoe and a bailing device for recovering drilling fluid from the borehole were designed. Most of the auxiliaries were tested during the summer of 2018–2019 near Zhongshan Station, East Antarctica while drilling to the bedrock to a depth of 198 m.

A new, modified version of the cable-suspended Ice and Bedrock Electromechanical Drill (IBED) was designed for drilling in firn, ice, debris-rich ice and rock. The upper part of the drill is almost the same for all drill variants and comprises four sections: cable termination, a slip-ring section, an antitorque system and an electronic pressure chamber. The lower part of the IBED comprises an auger core barrel, reamers, a core barrel for ice/debris-ice drilling and a conventional geological single-tube core barrel or custom-made double-tube core barrel. First, the short and full-scale field versions of the IBED were tested at an outdoor testing stand and a testing facility with a 12.5 m-deep ice well. Then, in the 2018–2019 summer season, the IBED was tested in the field at a site ~12 km south of Zhongshan Station, East Antarctica, and a ~6 cm bedrock core was recovered from a 198 m-deep borehole. A total of 18 d was required to penetrate the ice sheet. The retrieved core samples of blue ice, basal ice and bedrock provided valuable information regarding the Earth's paleo-environment.