To contribute to the treatment decision and optimize coagulase-negative staphylococcus (CNS) control programs, we conducted a meta-analysis to investigate the epidemiology and antimicrobial resistance rates of coagulase-negative staphylococcus associated with bovine mastitis in China. Three databases (PubMed, Google scholar and China National Knowledge Infrastructure database) were utilized to obtain relevant publications. A total of 18 publications were included in our research, and 3 of them included antimicrobial resistant (AMR) test. The pooled prevalence of coagulase-negative staphylococcus was 17.28%. Subgroup analysis revealed that the prevalence was higher in South China than in North China, was higher in 2011–2020 than in 2000–2010 and was higher in clinical bovine mastitis cases than in subclinical cases. The pooled AMR were most resistant to β-lactams, followed by tetracyclines, quinolones, nitrofurans, lincosamides, sulfonamides, amphenicol and aminoglycosides. The pooled AMR rate of coagulase-negative staphylococcus was lower in 2011–2020 than in 2000–2010. Although the prevalence of CNS showed an increasing trend over 20 years, the AMR rate showed a decreasing trend, and the clinical type of mastitis was the most frequent and the prevalence was highest in South China. Finally, CNS was most resistant to β-lactams amongst the eight groups of antimicrobial agents.

We numerically and experimentally investigate the multi-pulsing mechanism in a dispersion-managed mode-locked Yb-doped fiber laser. Multi-pulsing occurs primarily owing to the inherent filtering effect of the chirped fiber Bragg grating. The spectral filtering effect restricts the spectral broadening induced by self-phase modulation and causes extra loss, leading to a decreased pump power threshold for the multi-pulsing state. Numerical simulations show that multi-pulsing emerges at a lower pump power when the spectral filter bandwidth becomes narrower. In the experiment, the spectral width increases as the net cavity dispersion approaches zero. Pulses with wider spectral widths experience more loss from the spectral filtering effect, leading to a decreased pump power threshold for multi-pulsing. Therefore, the net cavity dispersion also has an impact on the multi-pulsing threshold. Based on this conclusion, we devise a strategy to obtain single-pulsing operation with the shortest pulse width and the highest pulse energy.

A deep ice core was drilled at Dome A, Antarctic Plateau, East Antarctica, which started with the installation of a casing in January 2012 and reached 800.8 m in January 2017. To date, a total of 337 successful ice-core drilling runs have been conducted, including 118 runs to drill the pilot hole. The total drilling time was 52 days, of which eight days were required for drilling down and reaming the pilot hole, and 44 days for deep ice coring. The average penetration depths of individual runs were 1 and 3.1 m for the pilot hole drilling and deep ice coring, respectively. The quality of the ice cores was imperfect in the brittle zone (650−800 m). Some of the troubles encountered are discussed for reference, such as armoured cable knotting, screws falling into the hole bottom, and damaged parts, among others.

In this paper, CNTs reinforced foam aluminum matrix composites with small pore diameter were prepared by powder metallurgy method. When the mass fraction of CNTs was 0.75%, the tensile strength, flexural strength and compressive yield strength of the materials were 3.4 times, 2.4 times and 2.4 times of pure foam aluminum, respectively, reaching the maximum value, which obviously improved the mechanical properties of aluminum foam. The tensile property model of foam aluminum matrix composites was built to predict the properties of the composites, and the effects of defects and reinforcement on the mechanical properties of the composites were compared. The results show that the tensile fitting is consistent with the measured results when the mass fraction of CNTs is less than 0.75%, but the weakening effect of defects on the strength of aluminum foam is much greater than the enhancement of CNTs. With the increase of CNTs mass fraction, the damping loss factor of foam aluminum composites increases, dislocation damping and grain boundary damping play a role in advance, and the damping peak moves to the low temperature region.

In the present study, the effect of Al addition on microstructure evolution, mechanical properties, and wear performances of a newly developed Ni–Si-containing complex brass was studied. The results showed that with increasing Al content from 0 to 3 wt%, the corresponding strengthening phase evolves from δ-Ni2Si to [Ni(Al)]2Si phases. Simultaneously, it is of great interest that the increasing Al addition also brings about a remarkable change in morphology of the secondary strengthening phase from dendrite and thin rod to regular block. Additionally, the hardness, yield strength and tensile strength of complex brass effectively increase with increasing Al content, and the fracture mechanism transforms from cleavage failure and microvoids accumulation fracture to cleavage failure. It was also found that the brass with adding 3 wt% Al exhibits the solidification microstructure with the uniform distribution of the block-shaped strengthening phase and has the best wear resistance. This present study provides a potential strategy for further improving the comprehensive performance of existing complex brass.

Iron carbide (Fe1−xCx) thin films were successfully grown by plasma-enhanced atomic layer deposition (PEALD) using bis(N,N′-di-tert-butylacetamidinato)iron(II) as a precursor and H2 plasma as a reactant. Smooth and pure Fe1−xCx thin films were obtained by the PEALD process in a layer-by-layer film growth fashion, and the x in the nominal formula of Fe1−xCx is approximately 0.26. For the wide PEALD temperature window from 80 to 210 °C, a saturated film growth rate of 0.04 nm/cycle was achieved. X-ray diffraction and transition electron microscope measurements show that the films grown at deposition temperature 80–170 °C are amorphous; however, at 210 °C, the crystal structure of Fe7C3 is formed. The conformality and resistivity of the deposited films have also been studied. At last, the PEALD Fe1−xCx on carbon cloth shows excellent electrocatalytic performance for hydrogen evolution.

We demonstrate a nonlinearity optimization method by altering distribution of passive fibers in a dissipative-soliton mode-locked fiber laser to level up output parameters. In the numerical simulation, we found that the passive fiber segment after gain fiber characterizes the highest average B-integral among fiber segments. By reducing the length of this fiber section and keeping the total passive fiber length as constant, the output pulse energy can be effectively scaled up while maintaining a short dechirped pulse duration, resulting in boosting peak power. With this method, 37-nJ pulses are generated from a dissipative-soliton mode-locked cladding pumped ytterbium-doped single-mode fiber laser in the experiment. The pulse can be dechirped to 66 fs with 350 kW peak power. Moreover, the pulse pedestal is suppressed by a vector-dispersion compressor.

We demonstrate an all polarization-maintaining (PM) fiber mode-locked laser seeded, hybrid fiber/solid-slab picosecond pulse laser system which outputs $40~\unicode[STIX]{x03BC}\text{J}$, 10 ps pulses at the central wavelength of 1064  nm. The beam quality factors $M^{2}$ in the unstable and stable directions are 1.35 and 1.31, respectively. $15~\unicode[STIX]{x03BC}\text{J}$ picosecond pulses at the central wavelength of 355 nm are generated through third harmonic generation (THG) by using two $\text{LiB}_{3}\text{O}_{5}$ (LBO) crystals, in order to get better processing efficiency on polycrystalline diamonds. The high pulse energy and beam quality of these ultraviolet (UV) picosecond pulses are confirmed by latter experiments of material processing on polycrystalline diamonds. This scheme which combines the advantages of the all PM fiber mode-locked laser and the solid-slab amplifier enables compact, robust and chirped pulse amplification-free amplification with high power picosecond pulses.