Hostname: page-component-78c5997874-m6dg7 Total loading time: 0 Render date: 2024-11-18T08:18:02.822Z Has data issue: false hasContentIssue false

Bending Shear: The Rate-controlling Mechanism for Calving Ice Walls*

Published online by Cambridge University Press:  20 January 2017

Terence Hughes
Affiliation:
Institute for Quaternary Studies and Department of Geological Sciences, University of Maine, Orono, Maine 04469, U.S.A.
Masayuki Nakagawa
Affiliation:
Kanazawa Women’s Junior College, Kanazawa, Ishikawa 920–13, Japan
Rights & Permissions [Opens in a new window]

Abstract

Bending shear was observed to produce nearly vertical shear bands in a calving ice wall standing on dry land on Deception Island (lat. 63.0°S., long. 60.6 W.), and slabs calved straight downward when shear rupture occurred along these shear bands (Hughes, 1989). A formula for the calving rate was developed from the Deception Island data, and we have attempted to justify generalizing this formula to include ice walls standing along beaches or in water. These are environments in which a wave-washed groove develops along the base of the ice wall or along a water line above the base. The rate of wave erosion provides an alternative mechanism for controlling the calving rate in these environments. We have determined that the rate at which bending creep produces nearly vertical shear bands, along which shear rupture occurs, controls the calving rate in all environments. Shear rupture occurs at a calving shear stress of about 1 bar. Our results justify using the calving formula to compute the calving rate of ice walls in computer models of ice-sheet dynamics. This is especially important in simulating retreat of Northern Hemisphere ice sheets during the last deglaciation, when marine and lacustrine environments were common along retreating ice margins. These margins would have been ice walls standing along beaches or in water, because floating ice shelves are not expected in the ablation zone of retreating ice sheets.

Type
Research Article
Copyright
Copyright © International Glaciological Society 1989

Introduction

Slabs calve from ice walls along shear bands that rise vertically from the base of the ice wall and curve slightly toward the ice wall (Reference HughesHughes, 1989). Shear strain in shear bands increases from zero at the base, which is a rigid boundary, to a maximum at the surface, which is a free boundary. In this respect, slip in shear bands is analogous to slip between pages of a book when the book is bent around its binding, where the binding is a rigid boundary. Based on this mechanism, a formula for the calving rate of slabs from an ice wall was derived in which calving rate uc is:

(1)

where us is the horizontal surface velocity of ice at the top of the ice wall, с is the horizontal distance between the ice wall and transverse crevasses immediately behind the ice wall, h is the height of the ice wall, θ is the angle through which the ice wall bends to produce the curving shear bands, and Rh/θ is the radius of bending curvature of the shear bands (Reference HughesHughes, 1989). For steady-state calving, uc = û = ku s, where и is the mean forward velocity of the ice wall and k: is a constant. Therefore, с = khθkh 2/R in Equation (1).

By definition, ice walls are grounded in water whose depth ranges from zero to the depth needed to float ice having the height of the ice wall. Equation (1) was derived using data obtained from an ice wall standing on dry land. When an ice wall stands in the intertidal zone of a beach, a wave-cut groove exists along the base of the ice wall. This groove exists along the water line when the ice wall is grounded in water. In addition, inhomogeneous creep in the curving shear bands interacts with homogeneous creep between shear bands that is described by lines of maximum shear stress intersecting the ice wall at 45° angles and which constitute the slip-line field for plastic flow. These features are illustrated in Figure 1. They pose this question: is the rate of slab calving controlled by the rate at which bending creep produces curving shear bands, the rate at which shear rupture occurs along slip lines, or the rate at which grooves are produced by wave action? We wish to present our answer to that question.

Fig.1. The bending creep mechanism for shear rupture in calving ice walls. Ice walls are shown grounded on dry land (lop), at the shoreline of a beach (middle), and in deep water (bottom). Straight dashed lines intersecting the ice wall at 45° are the slip lines of maximum shear stress for homogeneous creep, curving solid lines rising vertically from the bed are shear bands produced by bending creep. Heavy lines are calving surfaces for shear rupture.

Ice Walls Grounded on Dry Land

The role of shear rupture along slip lines was deduced from observations of a calving ice wall grounded on dry land in an eruption crater on Deception Island (Iat. 63.0 °S., long. 60.6 W.), which lies off the Antarctic Peninsula. Four tunnels were dug at various heights up the ice wall, and a shallow groove was cut down the entire height of the ice wall (Reference HughesHughes, 1989). These excavations revealed the bending shear mechanism shown schematically in Figure 2. The increase of bending shear with distance above the base of the ice wall was revealed by increasing offsets of ash and dust layers intersected by the shear bands. We determined crystal fabrics from ice samples taken from these excavations.

Fig.2. A cartoon of the crater produced by the 12 August 1970 subglacial volcanic eruption on Deception Island. Details of the up-slope ice wall show offsets of ash and dust layers by shear bands produced by a bending movement (from Reference HughesHughes. 1971).

An ice sample containing a shear band intersecting an ash layer is shown in Figure 3, and Figure 4 shows ice fabrics inside (Fig. 4a) and outside (Fig. 4b) of this shear band. Fabric (a) is the typical ice fabric in a shear band. It shows that optic axes (the crystallographic c-axes normal to easy-glide atomic planes of hexagonal symmetry) are strongly clustered near a pole at 90 to the plane of the shear band, and weakly clustered near a pole at 45° to this plane. Fabric (b) is the typical ice fabric between shear bands. It shows that optic axes are strongly clustered near a pole at 45 to the plane of the shear band and very weakly clustered near a pole at 0° to the plane of the shear band.

We interpret clustering of optic axes near the 90° pole as resulting from recrystallization within the shear band to produce an easy-glide ice fabric favoring inhomogeneous bending creep. We interpret clustering of optic axes near the 45 pole as resulting from homogeneous creep between shear bands to produce an easy-glide ice fabric favoring shear deformation along lines of maximum shear stress aligned at 45 to the ice wall (and, therefore, at nearly 45° to the shear bands), with this fabric predominating between shear bands and existing as a much weaker “ghost” fabric of unrecrystallized grains within shear bands. We interpret the very weak clustering of optic axes near the 0° pole observed between shear bands as resulting from basal traction, as this fabric becomes stronger in ice samples closer to the bed, and this pole is perpendicular to the bed, where basal traction tends to produce an easy-glide ice fabric having this pole orientation.

Fig.3. A dirt layer and air bubbles drawn into a shear band in the calving ice wall on Deception Island.

Fig.4. Ice fabrics in a thin section of the ice sample in Figure 3. Fabric (a) is contoured from 61 poles inside the shear band. Fabric (b) is contoured from SO poles outside the shear band. Numbers denote the per cent of c-axes per 1% of area in the Schmidt diagrams. The dirt layer in Figure 3 has the orientation shown.

Actual observations of slab calving on the Deception Island ice wall show that the easy-glide fabric for inhomogeneous bending creep in shear bands is superimposed on an older easy-glide fabric for homogeneous creep in the direction of the slip-line field (Reference HughesHughes, 1989). Slabs calve when easy glide in the shear bands drastically reduces coupling across shear bands and drastically enhances slip along shear bands. Since the shear bands are nearly vertical, up-glacier uncoupling means that virtually the entire weight of ice slabs between shear bands must be borne by ice at the base of these slabs. Shear rupture along a 45° plane near the base of the slab between the ice wall and the shear band will allow the slab to calve from the ice wall. Since the easy-glide ice fabric that exists in these 45° planes cannot lead to shear rupture until bending creep produces the easy-glide ice fabric in shear bands, bending creep is the rate-controlling process for slabs calved from ice walls grounded on dry land.

Ice Walls Grounded Along a Beach Shoreline

Along the northern Antarctic Peninsula, most calving ice walls are grounded in the intertidal zone of beaches. Similar ice walls may have extended along the beach shorelines of pro-glacial lakes during retreat of North American and Eurasian ice sheets after the last glacial maximum about 14 000 years ago. Hence, slab calving from these ice walls is the dominant ablation mechanism for glaciers on the northern Antarctic Peninsula today and may have been an important ablation mechanism during the last deglaciation.

The dominant features of intertidal ice walls along Antarctic beaches are a continuous shoreline groove at the base of the ice wall and large cavities in re-entrant angles of the ice wall. Both features are eroded by wave action in the intertidal zone between high and low tides, supplemented by waves that accompany storms. The grooves and cavities are everywhere, except for sections of the ice wall that are fresh un weathered fracture surfaces. Personal observations of calving events along these ice walls during November and December of 1988 showed that slab calving was caused by nearly vertical shear rupture along transverse crevasses immediately behind the ice wall. Moreover, the fresh surface exposed after a slab calved had the slight concave curvature that was observed in the nearly vertical shear bands produced by bending creep in the ice wall we studied in detail on Deception Island.

If development of shear bands by bending creep along the intertidal ice walls of the Antarctic Peninsula precedes undercutting of the ice wall by wave action, then the tidal groove and re-entrant cavities should be the exception rather than the rule for these ice walls, because shear rupture would occur as soon as the groove and cavities had undercut ice back to the shear band closest to the ice wall. On the other hand, if bending creep produced shear bands more slowly than wave action produced the groove and cavities, these intertidal features would be almost ubiquitous, because they would develop long before shear rupture in the shear bands produced calving events. Since intertidal grooves and cavities exist at the base of intertidal ice walls along nearly all shorelines of the Antarctic Peninsula, except where slabs have recently calved, we conclude that bending creep producing shear bands along which shear rupture occurs is the rate-controlling mechanism for slab-calving.

Ice Walls Grounded in Water

Calving ice walls standing in water exist along the margin of the Antarctic ice sheet everywhere except where the ice margin abuts mountains, forms an ice wall in the intertidal zone along beaches, or advances in water deep enough to float the ice and produce an ice shelf. Much of the Wilkes Land margin of the Antarctic ice sheet is an ice wall grounded in water. It is likely that retreating margins of the North American and Eurasian ice sheets during the last deglaciation often were ice walls grounded in sea-water along marine margins and in pro-glacial lakes along terrestrial margins. Slab calving is the dominant ablation mechanism where these ice walls exist in Antarctica today, and may have been an important ablation mechanism for retreating Northern Hemisphere ice sheets.

Wave-washed grooves form along the water line of ice walls grounded in water, and these grooves are enlarged into cavities in the re-entrant angles of the ice walls, where wave action is focused. Calving of ice slabs above the groove and cavities proceeds by the same mechanism that we observed for ice walls standing in the intertidal zone of beaches, where wave action produces a groove and cavities at the base of the ice wall. Under-water calving of ice beneath the wave-washed groove and cavities may also proceed by shear rupture along the shear bands produced by bending creep. The basic difference would be that shear rupture proceeds downward above the water line and upward below the water line.

In order for the calving rate to be the same above and below the water line, the downward gravity force and the upward buoyancy force that cause shear rupture above and below the wave-washed groove should produce identical calving stresses. Since the density of ice is about ten times the density difference between ice and water, slabs calved below the wave-washed groove must be about ten times larger than slabs calved above the groove if the upward and downward calving causes shear rupture at the same calving stress.

Calving Forces on Ice Walls

Nature abhors a vacuum, and air in front of an ice wall is a vacuum compared to ice in back of the ice wall, so a horizontal force exists that pulls the ice wall forward and opens transverse crevasses behind the ice wall. Shear rupture proceeds downward from these crevasses along shear bands produced by bending creep (Reference HughesHughes, 1989). For orthogonal axes with x horizontal and perpendicular to the ice wall, y horizontal and parallel to the ice wall, and z vertical, the horizontal pulling force Fx calving a slab of width w from an ice wall of height h standing in water of depth d is:

(2)

where ρ1 and ρw are ice and water densities and g is gravity acceleration. Pulling force Fx opens transverse crevasses behind the ice wall and induces a bending moment My (z) at the base of the ice wall that produces the shear bands extending upward from the base of the ice wall to the tips of surface crevasses, and along which shear rupture occurs. From Hughes (1989):

(3)

where z = 0 and z = h at the bottom and top of the ice wall, respectively. Notice that the bending moment decreases as water gets deeper, and vanishes at depth d = (ρIw)1/3A, which is greater than depth d = (ρ Iρw)h at which the ice wall floats and thereby creates an ice shelf. Hence, a bending moment exists so shear bands can form even after the ice floats.

For an ice wall grounded on dry land, a slab having height h, width w, and thickness с calves when a vertical gravity force Fz causes shear rupture across the shear bands produced by bending creep. The calving slab then slides across the plane in the slip-line field that intersects both the shear band and the ice wall at a 45 angle. Hence, shear rupture occurs only along distance h – с of the shear band and:

(4)

For an ice wall grounded in the intertidal zone of a beach, the basal groove and cavities eliminate shear rupture on the 45° planes and the calving force when the groove has radius r is:

(5)

For an ice wall grounded in water of depth d, the calving force above the wave-washed groove and cavities is:

(6)

and the calving force below the wave-washed groove and cavities is:

(7)

where C is the calving distance behind the submerged part of the ice wall.

Calving Stresses on Ice Walls

The calving stress on an ice wall would be calving force Fc divided by the area across which shear rupture occurs. For an ice wall grounded on land, this would be area w (h – c) of the shear band produced by bending creep and area (2)½ cw of the plane that lies in the slip-line field and intersects both the ice wall and the basal part of the shear band at a 45 angle. Since the rate of slab calving is controlled by shear rupture across the shear band, which has the larger area and therefore the lower stress for shear rupture, the calving stress is:

(8)

For an ice wall grounded in the wave-washed zone of a beach, shear rupture occurs only across shear bands produced by bending creep so that:

(9)

For an ice wall grounded in water, shear rupture above the water line occurs for:

(10)

and shear rupture below the water line occurs for:

(11)

where Equations (10) and (II) must be equal for the calving rate to be the same above and below the wave-washed groove and cavities, so that:

(12)

Since с = 10m is a typical slab thickness between fhe ice wall and the first transverse crevasse, Equations (8) through (11) give ∣τ0∣ 1 = 1 bar = 100kPa for the absolute value of the calving stress. Hence, it appears that a bending shear stress of about 1 bar is required to generate the easy-glide ice fabrics in shear bands that facilitate shear rupture.

Our only evidence that Equation (12) holds was our observation of a submarine calving event on San Rafael Glacier in the Chilean fjords on 21 November 1988. The submarine block that rose to the surface was about ten times larger than slabs calved above a wave-washed groove 3 m deep. The ice wall extended 100 and 50 m above and below sea-level near the fjord walls, and 130 and 120 m above and below sea-level near the center of the fjord, where the calving event occurred. Setting ρ1 = 920 kg/m3 for ice and ρw = 1020 kg/m3 for sea-water gives C = 9.2c in Equation (12). Other evidence that blocks calved below sea-level are much larger than slabs calved above sea-level for ice walls grounded in water is Figure 28 from Reference Post and LaChapellePost and LaChapelle (1971), a photograph showing these blocks and slabs floating in front of the South Sawyer Glacier calving ice wall in south-east Alaska.

We conducted laboratory creep experiments in which simple shear predominated, and we determined the shear stress needed to create an easy-glide ice fabric in a shear band of the same thickness as those produced by bending shear on the Deception Island calving ice wall. A poly-crystalline ice specimen having a random orientation of crystal grains was produced by packing snow into a mold 75 mm by 75 mm by 220 mm, saturating the snow with cold water, and freezing the mixture. This produced grains of about 1 mm in diameter. The sample was then removed from the mold and each end was frozen into twin box grips, 75 mm long, 75 mm wide, and 100 mm deep, of the creep machine shown schematically in Figure 5. Weights hung on the chain from the large-diameter wheel transmitted a constant shear stress to the 75 mm by 75 mm cross-section of ice exposed between the two box grips, by means of a chain from the small-diameter wheel.

As seen in Figure 5, the box grips moved in nearly frictionless ball-bearing housings, with vertical motion of one box grip allowing simple shear in the exposed specimen and horizontal motion of the other box grip suppressing uniaxial tension in the exposed specimen. Taking rectilinear axes with x horizontal and normal to the plane of shear, y horizontal, and z vertical and both parallel to the plane of shear, as shown in Figure 6, the exposed volume of the ice specimen was V = LXLYLZ , where LX could be varied, but LY = Lz = 75 mm is constant. The plane of shear initially had about 75 grains along Lz making the production of an easy-glide ice fabric independent of the initial grain-size. When a load was applied, one box grip underwent vertical translation uz and the other box grip underwent horizontal translation ux. Vertical motion introduces shear stress τ,χ in volume V and causes shear strain Ɛzx where 2ƐZx = tan ᵧ = u Z/L x Horizontal motion suppresses a tensile stress that would otherwise stretch volume V by an amount (sec ᵧ − 1)L x The only stresses are shear stress T zx and bending stress σ χχ , where volume V is bent near the box grips because the box grips do not rotate during translation uz (Reference DehlingerDehlinger, 1950; Reference ReadRead, 1950).

Fig.5. A schematic diagram showing the configuration of specimen grips and the applied load for simple shear-creep experiments. The creep machine is designed to conduct creep experiments in simple shear, uniaxial tension, uniaxial compression, and torsion, with constant stress in the uniaxial tests maintained using a variable lever-arm (Reference Garofalo, Richmond and DomisGarofalo and others. 1962).

The distribution of σ xx and T zx along L z is provided by beam theory. For elastic deformation σ xx varies linearly from σ xx = σ m for maximum tension (convex bending) or compression (concave bending) at z = ±Lz /2, to σxx = 0 at z = 0. For plastic deformation, δ xx = σm along L7, but changes abruptly from tension to compression at z= 0. For elastic deformation, Tzx varies parabolically from τ zx = 0 at z = ±LZ12 to Τ.χ = Tm for maximum shear at z = 0. For plastic deformation, Tzx = Tm along most of Lz except at z = ±LZ-/2, where an abrupt drop to τzx = 0 occurs.

Fig.6. Stresses and deformation of an ice specimen mounted in the simple shear-creep configuration shown in Figure 5. Top: the distribution of elastic shear stress τzx and bending stress σxx in response to shear force Fz and bending moment My at the onset of creep deformation. Bottom: the distribution of viscoplaslic shear and bending produced by strain γ at the conclusion of creep deformation. Bending is suppressed when Lx << Lz.

If simple shear is to produce an easy-glide fabric in exposed volume V of the specimen, τzx must dominate σχχ during creep deformation. A creep test began with elastic deformation producing the linear σxx and parabolic τ distribution along Lz shown in Figure 6. The ratio of exposed specimen lengths Lx and Lz needed for Tzx to dominate σxx can be computed readily for this situation. If σ is the average absolute value of σxx, then:

(13)

The bending moment about My у at the box grips is therefore:

(14)

where lever-arms

act on forces
, and
. If
is the average value of τ zx , then:
(15)

The bending moment about y at the box grips is therefore:

(16)

Equating Equations (14) and (16) for equilibrium gives:

(17)

The creep test was ended when recrystallization produced an easy-glide ice fabric that mimicked plastic deformation (Reference HughesHughes, 1977, fig. 23). Hence,

except at z = 0 and
except at z = ±L./2. Therefore:
(18)

for which

(19)

We conclude from Equations (17) and (19) that τzx will dominate σxx if Lz » Lx.

We conducted “creep experiments with Lx = 10mm and Lx = 20 mm, both for Lz = 75 mm. Recrystallization produced an easy-glide fabric in both cases. Slight bending at the box grips was observed for Lx = 20 mm, but none for Lx = 10 mm. Bending was monitored by freezing cross-hair threads into the ice specimen in order to compare local shear strain εzx = ½ (∂u z / ∂ x + Qux/z) = t\uz/2ALx midway between the box grips with shear strain tzx = i tan γ = uz/2Lx between the box grips. Box grips were used to prevent bending from detaching the specimen from the grips where bending stress σχχ was tensile and produced convex bends, as observed by Rigsby (1958).

Our laboratory creep experiments were conducted at −3°C, the mean annual temperature on Deception Island, and recrystallization invariably occurred when the applied shear stress approached 1 bar (100 kPa) and shear strain approached 10%. To illustrate this, Figure 7 compares creep data at −3°C for Tzx = 55 kPa and Tzx = 117kPa. At 55 kPa, recrystallization had not begun after 4 months, the time between the 12 August 1970 volcanic eruption that produced the ice wall on Deception Island and our initial observations of shear bands in the ice wall. In Figure 7, 1100 h of creep at 55 kPa had produced ε = 0.05 and a steady-state strain-rate of εzx = 0.40/a. At 117 kPa, recrystallization began at ε zx = 0.08 after 300 h of creep and ended at zzx = 0.40 after 300 additional hours of creep, to produce a steady-state strain-rate of i.x = 1.9/a before recrystallization and έ. = 24/a after recrystallization.

Fig.7. Creep curves for simple shear of laboratory polycrystalline ice conducted at −3°C using the creep configuration in Figure 5 to duplicate the shear hands in the calving ice wall on Deception Island. Curve A: τzx = 117 kPa; curve Β: Tzx = 55 kPa.

Measurements of the size and fabric of grains after recrystallization showed that ice in deformed volume V had an average grain diameter of 5 mm, compared to 1 mm before recrystallization, and that recrystallization had converted the random grain fabric into a single-maximum fabric in which optic axes were clustered tighly about a pole lying 90° from the plane of shear. Figures 8 and 9 show the grain-size and fabric after recrystallization. Even with a 5 mm diameter, sheared length L- of the specimen includes about 15 grains, so the increase in grain-size should not invalidate the creep experiments. Interestingly, the 5 mm diameter of recrystallized grains was also the most common grain-size in the Deception Island ice wall, both in and between shear bands. As is seen by comparing Figures 4 and 9, the single-maximum fabric for easy glide was much stronger in our laboratory creep experiments than in the Deception Island shear bands, even though total strain was much greater in the Deception Island shear bands. This may be because the original fabric was random in our laboratory ice but had a single-maximum fabric at 45 to the shear bands in Deception Island ice, a fabric that was retained between shear bands and even survived recrystallization in the shear bands, where it was weakened but not detroyed.

Fig.8. Grain-sizes in a thin section made from the ice specimen sheared in a laboratory creep experiment to produce the data for curve A in Figure 7. Recrystallization in the plane of shear was accompanied by grain growth.

Fig.9. The ice fabric in the recryslallized part of the thin section in Figure S. A single-maximum fabric exists in the plane of shear. Numbers denote the per cent of c-axes per 1% of area in the Schmidt diagram for 165 poles inside the shear band.

Recrystallization in the laboratory ice increased the strain-rate over ten-fold, from

to
5.5 × 10−3/h; that is, from έzx = 1.88/a to έ = 24.1/a.

We believe a drastic strain-rate increase of this order leads to shear rupture and slab calving along the ice wall on Deception Island, an increase that takes place in only about 300 h when the shear stress is about 1 bar. This is the shear stress for slab calving that is predicted by Equations (8) through (10) for ice walls when crevasses open about 10 m behind the wall, a common occurrence, and by Equation (11) for under-water block calving.

Our creep data allow a calculation of viscoplastic exponent n and hardness parameter A in the flow of ice for our close approximation to simple shear:

(20)

Using the creep data in Figure 7 as an example, if the two minimum strain-rates and applied shear stresses before recrystallization are designated by subscripts I and 2, respectively, Equation (20) gives η = In[(έzx)1/(έzx)2]/ In(Tzx)1 (Tzx) 2] = 2.07. This value of η is then used to obtain A =86.3 kPa a1/n and A = 25.2kPaa1/,! before and after recrystallization, respectively, from Equation (20) and the two sets of έ and Tzx data in Figure 7.

Our creep experiments gave η ≅ 2, which can be interpreted in two ways. First, following Reference WeertmanWeertman (1983), perhaps η S 1 for Tzx < 10kPa, η ≅ 3 for 10 kPa > τ > 100 kPa, and n>≅ 1 for τ > 100 kPa. On this basis, we should expect « S 3 in our experiments. Secondly, following Reference HughesHughes (1981), perhaps η ≅ 1 for transient creep and η ≅ 3 for steady-state creep. In this case, η at 2 implies that recrystallization began during transient creep in our creep experiment at 117 kPa, so that in Figure 7 the minimum creep rate at 117 kPa was not the true steady-state creep rate, whereas the minimum creep rate at 55 kPa was the true steady-state creep rate because recrystallization did not occur. Favoring this interpretation is the observation from polar ice sheets and ice shelves that η = 1 when transient creep is important (Reference Doake and WolffDoake and Wolff, 1985; Reference WeertmanWeertman, 1985), and a component of transient creep would exist in our ice specimens because the distribution of Tzx across Lz changes from parabolic to nearly constant during the creep test even though the applied was constant. Opposing this interpretation are the creep data by Reference DuvalDuval (1976), who found that η s 3 for both transient and steady-state creep (Reference HughesHughes, 1985). Although both field and laboratory studies give η≅ 3 as the most common value (Reference PatersonPaterson, 1981), lower values have been reported. Reference Colbeck and EvansColbeck and Evans (1973) obtained η = 1.3 for Blue Glacier, for example.

Our creep experiments gave unusually low values of hardness parameter A, both before and after recrystallization. Most published creep data report a softness parameter B, which is obtained from the flow law in our creep experiments, so that B = A “ from Equation (20). Converting A into B from our data for η = 2.07 gives B = 3.15 χ 1012 kPa−n s−1 before recrystallization and B = 4.02 χ 10−11RPa−wS−1 after recrystallization. Equivalent values for η = 3 would be B = 3.74 × 10−14 kPa−n s−1 before recrystallization and B = 4.77 χ 10−13 kPa−n s−1 after recrystallization. Reference PatersonPaterson (1981, table 3.1) presented field data from temperate glaciers ranging from η = 2.8 and B = 8.85 χ 1015 kPa a−1 to η = 5.2 and B = 5.06 × 10−20 kPa−n a−1. Reference PatersonPaterson (1981, table 3.2) presented laboratory data for the minimum creep rate in our stress range at or near —2 C. These data give a mean value of B = 2.7 ×10−15 kPa−ns−1 standardized for η = 3, but the largest value was ten times the smallest value. Our values of B standardized for η = 3 are outside the upper end of that range by a factor of 2.8 before recrystallization and by a factor of 35 after recrystallization. We conclude that our value of B is close to the usual range for minimum creep rates before recrystallization, but is unique after recrystallization.

The differences between our laboratory creep data and those tabulated by Reference PatersonPaterson (1981) may be explained by the different states of stress. The Reference PatersonPaterson (1981) data were for creep in uniaxial compression, in which the compressive stress was uniform across the specimen cross-section. Our data were for creep in simple shear, in which the shear stress varied across the specimen cross-section from zero at the sides to a maximum at the center, and only became relatively uniform after recrystallization. Consequently, recrystallization was not uniform; it began in the center and spread to the sides.

Conclusions

Calving ice walls are found grounded on dry land, along beaches, and in water. We have concluded that (1) in all these environments the rate-controlling calving mechanism is bending creep that produces nearly vertical shear bands in the ice wall, and leads to shear rupture along these bands, (2) the calving rate is accurately predicted by a calving formula based on this mechanism, using data from a calving ice wall on Deception Island, and (3) calving follows shear rupture at a shear stress of about 1 bar.

These results are fortunate because they (1) extend the calving formula developed for the Deception Island ice wall to all calving ice walls in all environments, (2) spare us from addressing turbulent flow, the one great unsolved problem of classical physics because, without bending creep, wave action would control the calving rate in beach and aquatic environments, and (3) allow us to incorporate the calving rate along with the melting rate in computer models that simulate advance and retreat of continental ice sheets in polar, lacustrine, and marine environments, where ice walls are grounded on land, along beaches, or in water.

Acknowledgements

Our field and laboratory studies of the Deception Island calving ice wall were conducted during 1970–74, H. Brecher, R. Curl, C Parkinson, and M. Scholz assisting in the field work. The calving mechanism and its universal application to ice walls emerged when one of us (Т.Н.) had opportunities to revisit the Deception Island ice wall and other ice walls along the Antarctic Peninsula and in the Chilean fjords during the 1982–83 and 1988–89 austral summers, through the courtesy of Salén Lindblad Cruises and Society Expeditions Cruises. This work was supported by U.S. National Science Foundation grants GV-36510 and DPP-8312196, and by Battelle, P.N.L., subcontract B-R7112-A-E.

Footnotes

page 260 note *

See Annals of Glaciology, Vol. 12, 1989, p. 204 for an extended abstract.

References

Colbeck, S.C. Evans, R.J.. 1973 A flow law for temperate glacier ice. J. Glaciol., 12(64), 7186.CrossRefGoogle Scholar
Dehlinger, U. 1950 The experimental and theoretical results of plasticity at normal speeds of strain. In Symposium on Plastic Deformation of Crystalline Solids. Pittsburgh, Mellon Institute, 103110.Google Scholar
Doake, C.S. Wolff, M.E.W.. 1985 Flow law for ice in polar ice sheets. Nature, 314(6008), 255257.CrossRefGoogle Scholar
Duval, P. 1976 Lois du fluage transitoire ou permanent de la glace polycristalline pour divers états de contrainte. Ann. Geophys., 32(4), 335350.Google Scholar
Garofalo, F. Richmond, O. Domis, W.F.. 1962 Design of apparatus for constant–stress or constant–load creep tests. J. Basic Eng., 84, 287293.CrossRefGoogle Scholar
Hughes, T. 1971 Nonhomogeneous strain studies on Antarctic glaciers. Antarct. J. U.S., 6(4), 8990.Google Scholar
Hughes, T. 1977 West Antarctic ice streams. Rev. Geophys. Space Phys., 15(1), 146.CrossRefGoogle Scholar
Hughes, T. 1981 Lithosphere deformation by continental ice sheets. Proc R. Soc London. Ser. A, 378(1775), 507527.Google Scholar
Hughes, T. 1985 Thermal convection in ice sheets: we look but do not see. J. Glaciol., 31(107), 3948.CrossRefGoogle Scholar
Hughes, T. 1989 Calving ice walls. Ann. Glaciol., 12, 7480.CrossRefGoogle Scholar
Paterson, W.S.B. 1981 The physics of glaciers. Second edition. Oxford, etc., Pergamon Press.Google Scholar
Post, A. LaChapelle, R.. 1971 Glacier ice. Seattle, University of Washington Press.Google Scholar
Read, W.T. 1950 Discussion following paper by U. Dehlinge, 1950: The experimental and theoretical results of plasticity at normal speeds of strain. In Symposium on Plastic Deformation of Crystalline Solids, Pittsburgh, Mellon Institute, 111112.Google Scholar
Rigsby, G.P. 1958 Effect of hydrostatic pressure on velocity of shear deformation of single ice crystals. J. Glaciol., 3(24), 273278.CrossRefGoogle Scholar
Weertman, J. 1983 Creep deformation of ice. Annu. Rev. Earth Planet. Sci., 11, 215240.CrossRefGoogle Scholar
Weertman, J. 1985 Unsolved problems of creep. Nature, 314(6008), 227.CrossRefGoogle Scholar
Figure 0

Fig.1. The bending creep mechanism for shear rupture in calving ice walls. Ice walls are shown grounded on dry land (lop), at the shoreline of a beach (middle), and in deep water (bottom). Straight dashed lines intersecting the ice wall at 45° are the slip lines of maximum shear stress for homogeneous creep, curving solid lines rising vertically from the bed are shear bands produced by bending creep. Heavy lines are calving surfaces for shear rupture.

Figure 1

Fig.2. A cartoon of the crater produced by the 12 August 1970 subglacial volcanic eruption on Deception Island. Details of the up-slope ice wall show offsets of ash and dust layers by shear bands produced by a bending movement (from Hughes. 1971).

Figure 2

Fig.3. A dirt layer and air bubbles drawn into a shear band in the calving ice wall on Deception Island.

Figure 3

Fig.4. Ice fabrics in a thin section of the ice sample in Figure 3. Fabric (a) is contoured from 61 poles inside the shear band. Fabric (b) is contoured from SO poles outside the shear band. Numbers denote the per cent of c-axes per 1% of area in the Schmidt diagrams. The dirt layer in Figure 3 has the orientation shown.

Figure 4

Fig.5. A schematic diagram showing the configuration of specimen grips and the applied load for simple shear-creep experiments. The creep machine is designed to conduct creep experiments in simple shear, uniaxial tension, uniaxial compression, and torsion, with constant stress in the uniaxial tests maintained using a variable lever-arm (Garofalo and others. 1962).

Figure 5

Fig.6. Stresses and deformation of an ice specimen mounted in the simple shear-creep configuration shown in Figure 5. Top: the distribution of elastic shear stress τzx and bending stress σxx in response to shear force Fz and bending moment My at the onset of creep deformation. Bottom: the distribution of viscoplaslic shear and bending produced by strain γ at the conclusion of creep deformation. Bending is suppressed when Lx << Lz.

Figure 6

Fig.7. Creep curves for simple shear of laboratory polycrystalline ice conducted at −3°C using the creep configuration in Figure 5 to duplicate the shear hands in the calving ice wall on Deception Island. Curve A: τzx = 117 kPa; curve Β: Tzx = 55 kPa.

Figure 7

Fig.8. Grain-sizes in a thin section made from the ice specimen sheared in a laboratory creep experiment to produce the data for curve A in Figure 7. Recrystallization in the plane of shear was accompanied by grain growth.

Figure 8

Fig.9. The ice fabric in the recryslallized part of the thin section in Figure S. A single-maximum fabric exists in the plane of shear. Numbers denote the per cent of c-axes per 1% of area in the Schmidt diagram for 165 poles inside the shear band.