This Special Issue of the Robotica is on recent advances in field and service robotics with a focus on the use of robotic and autonomous technologies to handle tasks in harsh environments and tasks that involve the multirobot cooperation and human–robot interactions.

This paper presents a new approach for geometrically constrained path planning applied to the field of robotic grasping. The method proposed in this paper is based on the Fast Marching Square (FM $\, ^2$ ) and a path calculation approach based on an optimization evolutionary filter named Differential Evolution (DE). The geometric restrictions caused by the link lengths of the kinematic chain composed by the robot arm and hand are introduced in the path calculation phase. This phase uses both the funnel potential of the surroundings created with FM $\, ^2$ and the kinematic constraints of the robot as cost functions to be minimized by the evolutionary filter. The use of an optimization filter allows for a near-optimal solution that satisfies the kinematic restrictions, while preserving the characteristics of a path computed with FM $\, ^2$ . The proposed method is tested in a simulation using a robot composed by a mobile base with two arms.

This article presents modelling, simulation, and development of a wall-climbing robot based on coupled wheel and arm-type locomotion mechanism. The developed robot consists of two mobile modules connected with a robot arm mechanism. The actuation of the robot arm is inspired by inchworm locomotion, particularly during wall-to-wall transition, obstacle avoidance, and uneven surface locomotion. Easiness in the interchanging of wheel to arm and vice versa makes the robot more effective compared to previously developed wall-climbing robots. The kinematic and dynamic model for the proposed coupled wheel and arm locomotion concept has been established. A combination of particle swarm optimization (PSO) and proportional, integral, derivatives (PID) feedback control algorithm has been developed using MATLAB to simulate the different cases of robot motions. The developed prototype of the wall-climbing robot is used to verify the coupled wheel and arm locomotion concept in various wall climbing scenarios. The simulation and experimental findings show good comparisons and validate the model-based design of the wall-climbing robot.

“Picking out the impurities” is a typical scenario in production line which is both time consuming and laborious. In this article, we propose a target-oriented robotic push-grasping system which is able to actively discover and pick the impurities in dense environments with the synergies between pushing and grasping actions. First, we propose an attention module, which includes target saliency detection and density-based occluded-region inference. Without the necessity of expensive labeling of semantic segmentation, our attention module can quickly locate the targets in the view or predict the candidate regions where the targets are most likely to be occluded. Second, we propose a push–grasp synergy framework to sequentially select proper actions in different situations until all targets are picked out. Moreover, we introduce an active pushing mechanism based on a novel metric, namely Target-Centric Dispersion Degree (TCDD) for better grasping. TCDD describes whether the targets are isolated from the surrounding objects. With this metric, the robot becomes more focused on the actions around the targets and push irrelevant objects away. Experimental results on both simulated environment and real-world environment show that our proposed system outperforms several baseline approaches,which also has the capability to be generalized to new scenarios.

There has been an increasing interest in the application of robotic autonomous systems (RASs) for construction and mining, particularly the use of RAS technologies to respond to the emergent issues for earthmoving equipment operating in volatile environments and for the need of multiplatform cooperation. Researchers and practitioners are in need of techniques and developments to deal with these challenges. To address this topic for earthmoving automation, this paper presents a comprehensive survey of significant contributions and recent advances, as reported in the literature, databases of professional societies, and technical documentation from the Original Equipment Manufacturers (OEM). In dealing with volatile environments, advances in sensing, communication and software, data analytics, as well as self-driving technologies can be made to work reliably and have drastically increased safety. It is envisaged that an automated earthmoving site within this decade will manifest the collaboration of bulldozers, graders, and excavators to undertake ground-based tasks without operators behind the cabin controls; in some cases, the machines will be without cabins. It is worth for relevant small- and medium-sized enterprises developing their products to meet the market demands in this area. The study also discusses on future directions for research and development to provide green solutions to earthmoving.

In this paper, a novel self-adaptive underactuated robot hand with rigid-flexible coupling fingers (SAU-RFC hand) is proposed. The seven degrees of freedom (DOFs) SAU-RFC hand is driven by four servomotors, consists of three fingers, including two side-turning (ST) fingers and one non-side-turning finger. Specially, the ST fingers can perform synchronous reverse rotation laterally with each other. Each finger with three joints and two DOFs introduces a flexible structure, and the inner part of the proximal phalanx that makes most of the contact with the object is replaced by a flexible belt. The fingers can generate flexion/extension under the pull of the flexible belt, and the middle and distal phalanxes are mechanically coupled through a four-bar linkage. In particular, the flexible belt in the inner direction of the finger will deform, while it will not deform in the outer direction since the outer is a rigid structure. The flexible belt not only plays the role of transmitting power but also has the effect of uniformizing the contact force. Due to the rigid-flexible finger structure, the developed robot hand has a higher self-adaptive grasping ability for objects with different shapes, sizes, and hardness. In addition, the kinematic and kinetic analyses of SAU-RFC hand are performed. A contact force distribution model is established for the flexible belt, which demonstrates its effect of promoting uniform force distribution theoretically. In the end, experiments are conducted on different objects to verify the performance of SAU-RFC hand.

Today, demandsin industrial manufacturing mandate humans to work with large-scale industrial robots, and this collaboration may result in dangerous conditions for humans. To deal with this situation, this work proposes a novel approach for redundant large-scale industrial robots. In the proposed approach, an admittance controller is designed to regulate the interaction between the end effector of the robot and the human. Additionally, an obstacle avoidance algorithm is implemented in the null space of the robot to prevent any possible unexpected collision between the human and the links of the robot. After safety performance of this approach is verified via simulations and experimental studies, the effect of the parameters of the admittance controller on the performance of collaboration in terms of both accuracy and total human effort is investigated. This investigation is carried out via 8 experiments by the participation of 10 test subjects in which the effect of different admittance controller parameters such as mass and damper are compared. As a result of this investigation, tuning insights for such parameters are revealed.

Over the years, face recognition has been the research topic that has attracted many researchers around the world. One of the most significant applications of face recognition is the access control system. The access control system allows authorized persons to enter or exit certain or restricted areas. As a result, it will increase the security situation without over-investment in staff security. The access information can be the identification, time, and location, etc. It can be used to carry out human resource management tasks such as attendance and inspection of employees in a more fair and transparent manner. Although face recognition has been widely used in access control systems because of its better accuracy and convenience without requiring too much user cooperation, the 2D-based face recognition systems also retain many limitations due to the variations in pose and illumination. By analyzing facial geometries, 3D facial recognition systems can theoretically overcome the disadvantages of prior 2D methods and improve robustness in different working conditions. In this paper, we propose the 3D facial recognition algorithm for use in an access control system. The proposed algorithm includes the preprocessing, feature extraction, and classification stages. The application of the proposed access control system is the automatic sliding door, the controller of the system, the web-based monitoring, control, and storage of data.

At present, the study on autonomous unmanned ground vehicle navigation in an unstructured environment is still facing great challenges and is of great significance in scenarios where search and rescue robots, planetary exploration robots, and agricultural robots are needed. In this paper, we proposed an autonomous navigation method for unstructured environments based on terrain constraints. Efficient path search and trajectory optimization on octree map are proposed to generate trajectories, which can effectively avoid various obstacles in off-road environments, such as dynamic obstacles and negative obstacles, to reach the specified destination. We have conducted empirical experiments in both simulated and real environments, and the results show that our approach achieved superior performance in dynamic obstacle avoidance tasks and mapless navigation tasks compared to the traditional 2-dimensional or 2.5-dimensional navigation methods.