Hostname: page-component-848d4c4894-4rdrl Total loading time: 0 Render date: 2024-06-21T01:42:34.648Z Has data issue: false hasContentIssue false
  • English
  • Français

Superplasticity in P/M Aluminium Alloys

Published online by Cambridge University Press:  16 February 2011

K. Higashi ,
S. Tanimura  and
T. Ito
K. Higashi
Affiliation:
Department of Mechanical Engineering, College of Engineering, University of Osaka Prefecture, Mozu-Umemachl, Sakal, Osaka 591, Japan
S. Tanimura
Affiliation:
Department of Mechanical Engineering, College of Engineering, University of Osaka Prefecture, Mozu-Umemachl, Sakal, Osaka 591, Japan
T. Ito
Affiliation:
Department of Metallurgical Engineering, College of Engineering, University of Osaka Prefecture, Mozu-Umemachl, Sakal, Osaka 591, Japan
Get access

Abstract

Recent advances in the technologies of powder metallurgy lead to the development of some superplastic aluminium alloys containing a deliberate addition of a large amount of Zr and /or Cr and Mn that exhibit the high strain rates superplasticity. For a few alloy systems, the large elongation more than 500% has been observed over the strain rates of 1×10−1s−1, which rates are two or three orders of magnitude faster than those at which superplasticity is found in conventional superplastic aluminium alloys produced by ingot metallurgy. The high strain-rates superplasticity obtained in both type of fully static recrystallized and dynamic recrystallized P/M aluminium alloys. The decreasing of initial size of grains and/or sub-grains leads to the increasing the strain-rates for superplastic flow in both types of alloys. The refinement of grains or sub-grains size is one of necessary and important to obtain the high strain-rates superplasticity.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 196: Symposium T – Superplasticity in Metals, Ceramics, and Intermetallics , 1990 , 385
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Nieh, T.G.,Henshall, C.A. and Wadsworth, J., Scr. Metall.,18,1405(1984).Google Scholar
2. Nieh, T.G.,Gilman, P.S. and Wadsworth, J., Scr. Metall.,19,1375(1985).Google Scholar
3. Bieler, T.R.,Nieh, T.G., Wadsworth, J. and Mukherjee, A.K., Scr. Metall.,22,81(1988).Google Scholar
4. Sherby, O.D., ISIJ International,29,698(1989).Google Scholar
5. Matsuki, K.,Staniek, G.,Nakagawa, H. and Tokizawa, M.,Z. Metallkde, 79, 231 (1988).Google Scholar
6. Higashi, K.,Imamura, H.,Ito, T. and Tanimura, S.,“Superplasticity in Aerospace II”, ED., McNelley, T.R.. TMS,(1990). In Press.Google Scholar
7. Sherby, O.D. and Wadsworth, J., “Deformation Processing and Structure”, ED., Krauss, G., Am.Soc. Met., Metals Park,OH,355,(1984).Google Scholar
8. Arieli, A. and Mukherjee, A.K., Mater.Sci.Eng.,45,61(1980).Google Scholar
9. Rao, M.K. and Mukherjee, A.K., Mater.Sci.Eng.,80,181(1986).Google Scholar
10. Mukherjee, A.K.,Bieler, T.R. and Chokshi, A.H.,Proce. of 10th Riso Inter.Sympo., ED.,Bilde-Sorensen, J.B. et al., Riso National Laboratory, Demark, 207(1989).Google Scholar