Hostname: page-component-7c8c6479df-xxrs7 Total loading time: 0 Render date: 2024-03-29T11:46:56.668Z Has data issue: false hasContentIssue false

Finite Element Simulation of Steel Quench Distortion- Parametric Analysis of Processing Variables

Published online by Cambridge University Press:  28 February 2013

F. A. García-Pastor
Affiliation:
Cinvestav Unidad Saltillo, Carretera Saltillo-Monterrey Km 13, Ramos Arizpe, Coahuila, Mexico San Luis Rassini, Puerto Arturo No. 803, Piedras Negras, Coahuila, Mexico
R.D. López-García
Affiliation:
Cinvestav Unidad Saltillo, Carretera Saltillo-Monterrey Km 13, Ramos Arizpe, Coahuila, Mexico San Luis Rassini, Puerto Arturo No. 803, Piedras Negras, Coahuila, Mexico
E. Alfaro-López
Affiliation:
Cinvestav Unidad Saltillo, Carretera Saltillo-Monterrey Km 13, Ramos Arizpe, Coahuila, Mexico San Luis Rassini, Puerto Arturo No. 803, Piedras Negras, Coahuila, Mexico
M. J. Castro-Román
Affiliation:
Cinvestav Unidad Saltillo, Carretera Saltillo-Monterrey Km 13, Ramos Arizpe, Coahuila, Mexico San Luis Rassini, Puerto Arturo No. 803, Piedras Negras, Coahuila, Mexico
Get access

Abstract

Steel quenching from the austenite region is a widely used industrial process to increase strength and hardness through the martensitic transformation. It is well known, however, that it is very likely that macroscopic distortion occurs during the quenching process. This distortion is caused by the rapidly varying internal stress fields, which may change sign between tension and compression several times during quenching. If the maximum internal stress is greater than the yield stress at given processing temperature, plastic deformation will occur and, depending on its magnitude, macroscopic distortion may become apparent.

The complex interaction between thermal contraction and the expansion resulting from the martensitic transformation is behind the sign changes in the internal stress fields. Variations in the steel composition and cooling rate will result in a number of different paths, which the internal stresses will follow during processing. Depending on the route followed, the martensitic transformation may hinder the thermal stresses evolution to the point where the stress fields throughout the component may actually be reverted. A different path may support the thermal stresses evolution further increasing their magnitude. The cross-sectional area also affects the internal stresses magnitude, since smaller areas will have further trouble to accommodate stress, thus increasing the distortion. Additionally, the bainitic transformation occurring during relatively slow cooling rates may have an important effect in the final stress field state.

A finite-element (FE) model of steel quenching has been developed in the DEFORM 3D simulation environment. This model has taken into account the kinetics of both austenite-bainite and austenite-martensite transformations in a simplified leaf spring geometry. The results are discussed in terms of the optimal processing parameters obtained by the simulation against the limitations in current industrial practice.

Type
Articles
Copyright
Copyright © Materials Research Society 2013 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Totten, G.E. and Howes, M.A.H., Distortion of Heat Treated Components, chapter 5, Steel Heat Treatment Handbook, G.E. Totten and M.A.H. Howes, Ed., 1997, Marcel Dekker, p. 292.Google Scholar
Pietzsch, R., Brzoza, M., Kaymak, Y., Specht, E., & Bertram, A. Simulation of the Distortion of Long Steel Profiles During Cooling. Journal of Applied Mechanics, 74(3), 427 (2007). doi:10.1115/1.2338050 CrossRefGoogle Scholar
Nallathambi, A. K., Kaymak, Y., Specht, E., & Bertram, A. (2010). Sensitivity of material properties on distortion and residual stresses during metal quenching processes. Journal of Materials Processing Technology, 210(2), 204211. doi:10.1016/j.jmatprotec.2009.09.001 CrossRefGoogle Scholar
Lee, S. J., Lee, Y. K.. Finite element simulation of quench distortion in a low alloy steel incorporating transformation kinetics. Acta Materialia No. 56 (2008), p. 14821490. doi:10.1016/j.actamat.2007.11.039 CrossRefGoogle Scholar
San Martín, D., Rivera-Díaz-del-Castillo, P. E. J., & García-de-Andrés, C. In situ study of austenite formation by dilatometry in a low carbon microalloyed steel. Scripta Materialia, No. 58 (2008)., pp. 926929. doi:10.1016/j.scriptamat.2008.01.019 CrossRefGoogle Scholar
Jung, M., Kang, M., & Lee, Y.-K. (2012). Finite-element simulation of quenching incorporating improved transformation kinetics in a plain medium-carbon steel. Acta Materialia, 60(2), 525536. doi:10.1016/j.actamat.2011.10.007 CrossRefGoogle Scholar
Van Bohemen, S. M. C., & Sietsma, J. The kinetics of bainite and martensite formation in steels during cooling. Materials Science and Engineering: A, 527(24-25) (2010), pp 66726676. doi:10.1016/j.msea.2010.06.091 CrossRefGoogle Scholar