Hostname: page-component-8448b6f56d-cfpbc Total loading time: 0 Render date: 2024-04-20T02:45:00.893Z Has data issue: false hasContentIssue false
  • English
  • Français

Fabrication of Flexible One-Dimensional Porous Silicon Photonic Band-Gap Structures

Published online by Cambridge University Press:  01 February 2011

Natalya Tokranova ,
Bai Xu  and
James Castracane
Natalya Tokranova
Affiliation:
School of NanoSciences and NanoEngineering, University at Albany (SUNY)
Bai Xu
Affiliation:
School of NanoSciences and NanoEngineering, University at Albany (SUNY)
James Castracane
Affiliation:
School of NanoSciences and NanoEngineering, University at Albany (SUNY)
Get access

Extract

Photonic crystals are periodic dielectric structures that have a photonic band gap to control the propagation of light in a certain wavelength range. This property offers a means to manipulate photons in the same way as electrons can be controlled in an atomic lattice. Porous silicon is an ideal candidate fo r the fabrication of photonic crystals because of the availability of a variety of silicon micromachining techniques. One-dimensional photonic crystals with customized parameters can be economically fabricated using porous silicon multilayer structures with periodically modulated porosity. Despite the structural non-homogeneities, porous silicon fabricated on a p-type Si substrate has optical properties similar to a dielectric material with a single effective refractive index. The exact value of the refractive index for each layer depends on its porosity. An engineered porosity can be obtained by changing the etching currents during the anodization process. This results in a modulation of the refractive index. A stack of alternating layers with high and low porosity produces a distributed Bragg reflector (DBR). Various designs incorporating multilayer porous silicon structures with an optical Fabry-Perot resonator and coupled microcavities are under development and can serve as an optical filter. Prototypes of such free-standing structures with 21–200 stacked layers to be used as DBRs, Fabry-Perot resonators or coupled microcavities are being fabricated. These structures are coated with polystyrenesulfonate on their backsides to increase mechanical strength and at the same time maintain flexibility. In this work, reflectance spectra of these porous silicon multilayers with and without polymer on the backside were measured. Simulations of the multilayer one-dimensional photonic crystals were performed to predic t the reflectance spectrum and optimize their structures before the fabrication and to compare to experimental data.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 797: Symposium W – Engineered Porosity for Microphotonics and Plasmonics , 2003 , W1.3
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Lin, S. Y., Fleming, J. G., Hetherington, D. L., Smith, B. K., Biswas, R., Ho, K. M., Sigalas, M. M., Zubrzycki, W., Kurtz, S. R. and Jim, Bur “A three-dimensional photonic crystal operating at infrared wavelengths” Nature, 394, 251–253, 1998 Google Scholar
2. Blanco, A., Chomski, E., Grabtchak, S., Ibisate, M., John, S., Leonard, S.W., Lopez, C., Meseguer, F., Miguez, H., Mondia, J.P., Ozin, G.A., Toader, O., and Van Driel, H.M. “Large-scale synthesis of a silicon photonic crystal with a complete three-dimensional bandgap near 1.5 micrometers” Nature, 405, 437–440, 2000 Google Scholar
3. Birner, A., Wehrspohn, R.B., Gosele, U.M., Busch, K. “Silicon-based Photonic Crystals” Adv.Mater., 13, 377–388 (2001)Google Scholar
4. Scalora, M., Flynn, R. J., Reinhardt, S. B., Fork, R. L., Bloemer, M. J., Tocci, M. D., Bowden, C. M., Ledbetter, H. S., Bendickson, J. M., Dowling, J. P., Leavitt, R. P. “Ultrashort pulse propagation at the photonic band edge: Large tunable group delay with minimal distortion and loss” Phys. Rev. E 54, 1078–1081 (1996)Google Scholar
5. Kashkarov, P.K., Golovan, L.A., Fedotov, A.B., Efimova, A.I., Kuznetsova, L.P., Timoshenko, V.Y., Sidorov-Biryukov, D.A., Zheltikov, A.M., Haus, J.W. “Photonic bandgap materials and birefringent layers based on anisotropically nanostructured silicon” J. Opt. Soc. Amer. B 19, 2273–2281 (2002)Google Scholar
6. Centini, M., Sibilia, C., Scalora, M., D'Aguanno, G., Bertolotti, M., Bloemer, M. J., Bowden, C. M., and Nefedov, I. “Dispersive properties of finite, one-dimensional photonic band gap structures: Applications to nonlinear quadratic interactions” Phys. Rev. E 60, 4891–4898 (1999)Google Scholar
7. Lugo, J.E., Lopez, H.A., Chan, S. and Fauchet, P.M. “Porous multilayer structures: A photonic band gap analysis” J. Appl. Phys., vol. 91, 8, p.4966–4972 (2002)Google Scholar
8. Pavesi, L., Mulloni, V. “All porous silicon microcavities: growth and physics” Journal of Luminescence 80 (1999) pp. 43–52 Google Scholar
9. Halimaoui, A., in “Properties of Porous Silicon”, edited by Canham, L.V. (INSPEC, London, 1997), Vol. 18, p. 18 Google Scholar
10. Pavesi, L., Panzarini, G., Andreani, L.C. “All-porous silicon-coupled micricavities: Experiment versus theory” Phys. Rev. B 56, p. 15 794–15 800 (1998)Google Scholar
11. Ghulinyan, M., Oton, C.J., Bonetti, G., Gaburro, Z., and Pavesi, L. “Free-standing porous silicon single and multiple optical cavities” J. Appl. Phys., 93, p.9724–9729 (2003)Google Scholar